User's Guide

ManualsBrandsTyco Safety Products/Sensormatic ManualsElectronicsWIRELESS LR-WPAN IN 2.4 GHz BAND USING DIGITAL SS.

ZBAMB2070 MOBILE HANDHELD DEACTIVATOR 8200-0958-05, REV. A

INSTALLATION AND USER GUIDE

1 of 5

ZBAMB2070

Mobile Handheld

Deactivator

For use with a Motorola MT2070

handheld barcode scanner

User Guide

The ZBAMB2070 Mobile Handheld

Deactivator combines a Motorola MT2070

barcode scanner with a rechargeable

battery-operated deactivator coil.

This guide covers:

• Using the device

• Charging the battery

• Replacing the battery.

If you need assistance...

Contact your Sales Representative.

Safety

WARNING:

• No serviceable parts! Opening

the deactivator may expose

you to electric shock! If the

deactivator appears defective,

have your loss prevention

manager or IT specialist return

it to the distributor.

• Never use a damaged

deactivator.

WARNING:

• The deactivator is not to be

used for scanning a person.

Always keep a distance of at

least 35cm (14in) between the

deactivation coil and another

person. Refer to the Safety

Notice on page 5.

• Ensure safety instructions

within this manual are observed

during the installation and/or

operation of the deactivator.

• For proper charging, rest the

deactivator in the Motorola

Base Charging Station exactly

as shown in the image. Resting

the deactivator any other way

will affect its operation.

Motorola MT2070

Handhe

ld Scanner

Motorola MT2070

Base

Charging Station

ZBAMB2070 EAS Deactivator

Module

Assembly (dark

shaded parts)

Summary of content (5 pages)

PAGE 1
Safety ZBAMB2070 Mobile Handheld Deactivator WARNING: • No serviceable parts! Opening the deactivator may expose you to electric shock! If the deactivator appears defective, have your loss prevention manager or IT specialist return it to the distributor. For use with a Motorola MT2070 handheld barcode scanner User Guide The ZBAMB2070 Mobile Handheld Deactivator combines a Motorola MT2070 barcode scanner with a rechargeable battery-operated deactivator coil. • Never use a damaged deactivator.
PAGE 2
3. Swirl the deactivator coil in 2.54cm (1in) circles no more than 11.4cm (4.5in) from the barcode. Observe deactivation indications. Using the Device 1. Remove the scanner/deactivator from the Motorola Base Charging Station. 2. Aim the scanner at the barcode and: a) Pull the trigger. The scanner will beep indicating a successful scan. IIIIIIIIIIIIIIIIIIIII b) Release the trigger; the LEDs on the deactivator will flash yellow for 3 seconds. Within this window, perform step 3.
PAGE 3
Battery Charging Indicators Charging the Battery The handheld deactivator has a rechargeable battery. LEDs on the deactivator will flash green when the battery is charging or red if the battery charge is low. Both LEDs Indicate Flashing green Charging Solid green Fully charged IMPORTANT! To maintain the battery charge, rest the deactivator in the Motorola Base Charging Station exactly as shown below when not in use.
PAGE 4
2. Remove the battery and disconnect it. Replacing the Battery To replace the battery, see your loss prevention manager or IT specialist. WARNING: Risk of explosion if the battery is replaced with an incorrect size and type. WARNING: Recycle or dispose used batteries according to local or state requirements. DO NOT mutilate the battery or expose it to flame. Before recycling or disposing, insulate exposed battery wires with electrical tape. 1.
PAGE 5
Declarations Other Declarations WARRANTY DISCLAIMER: Sensormatic Electronics, LLC makes no representation or warranty with respect to the contents hereof and specifically disclaims any implied warranties of merchantability or fitness for any particular purpose. Further, Sensormatic Electronics, LLC reserves the right to revise this publication and make changes from time to time in the content hereof without obligation of Sensormatic Electronics, LLC to notify any person of such revision or changes.