Install Guide

Preliminary
ZBAMB9010-IPS EAS LABEL DEACTIVATION CONTROLLER 8200-0747-24 REV. 3A
INSTALLATION GUIDE
6 OF 7
Specifications
Electrical
Voltage input
to power supply............................ 100–240Vac,
50/60Hz (±5%)
Voltage input
from power supply ....................... 22.5Vdc
AC line current ............................. 2.5Arms max.
Scan I/O port:
Maximum input voltage ............ +25Vdc (±5%)
Input 1+ and Input 2+:
Input voltage ......................... ±5–12Vdc typical,
greater than 12V
observing the 32mA
maximum
Input current ......................... 10mA source minimum
Minimum pulse duration ....... 100ms
Detect out ............................. Open-collector side of
an opto-isolator
Maximum pull-up voltage ..... +25Vdc
This output remains in
the open state until
label detection occurs.
It then shorts to the
Detect Common for a
minimum of 39ms
based on label vicinity
to the antenna plus 7
detection windows
(5.555 x 7 = 39mS).
Detect common .................... Emitter side of the
Detect Out opto-
isolator. It normally
should be tied to D
Ground (J8, Pin 6).
Maximum current limit:
6.3mA @ Vce < 10V
2mA @ Vce < 0.4V
Environmental
Operating temperature ................. 0 to 40°C
(32° to 104°F)
Non-operating temperature .......... –40° to 70°C
(–40° to 158°F)
Relative humidity ......................... 0 to 90%
non-condensing
Mechanical
Height .......................................... 10.1cm (4in)
Width ........................................... 26.2cm (10.3in)
Depth ........................................... 22.1cm (8.7in)
Weight ......................................... 2.5kg (5.5 lbs)
Connector Inputs/Outputs
Each Network RS485 Port (8 pin modular jack)
Pin 1: RS485 HI (RS-485 Driver A)
Pin 2: RS485 LO (RS-485 Driver B)
Pin 3: Universal Sync A (RS-485 Driver A)
Pin 4: +5V* (Configurator controlled on/off, 250mA max.)
Pin 5: Spare +5V* (Configurator controlled on/off, 250mA
max.)
Pin 6: Universal Sync B (RS-485 Driver B)
Pin 7: D Ground
Pin 8: D Ground
*Can be +12V if powered by an LDM II.
Scanner Port (8-pin modular jack)
See specs opposite.
Pin 1: +5Vdc (125mA max.)
Pin 2: Scan In + (390 ohms in series with opto LED
anode)
Pin 3: Scan In – (opto LED cathode)
Pin 4: Detect Open Emitter (usually tied to D Ground, pin
6)
Pin 5: Detect Open Collector (0.15-0.4V @ 2mA output
low level when Detect OE grounded)
Pin 6: D Ground
Pin 7: RXD POS (RS-232 levels)
Pin 8: TXD POS (RS-232 levels)
Service RS-232 Port (4-pin modular jack)
Note: The Service Port should not be used for POS
applications. Use the Scanner Port.
Pin 1: RXD
Pin 2: TXD
Pin 3: D Ground
Pin 4: Not Connected
Remote Port (6-pin Modular Jack)
Pin 1: +22V (75mA max.)
Pin 2: Red LED
Pin 3: Green LED
Pin 4: Audio
Pin 5: Key Switch
Pin 6: P Ground
Antenna Out Ports
Pin 1: X
Pin 2: Y
Pin 3: X Ret
Pin 4: Y Ret
Pin 5: Chassis Ground
Pin 6: EEPROM Signal