Install Guide

ManualsBrandsTyco Safety Products/Sensormatic ManualsElectronicsANTI THEFT DEVICE

Preliminary

AMS-9030 CONTROLLER 8200-0344-02, REV. 0

INSTALLATION GUIDE

1 of 16

AMS-9030 Controller

Installation Guide

ZE9030

Contents

About this Guide .................................................... 1

Controller Overview ............................................... 2

Installation Requirements ...................................... 2

Mounting the Controller ......................................... 3

Connecting Antennas ............................................4

Connecting Remote Alarms................................. 12

Connecting External Devices to Controller Relays

............................................................................. 12

Connecting Noise Canceling Antennas ............... 13

Connecting Multiple 9030 Controllers.................. 13

Connecting a Service Laptop .............................. 14

Connecting a SyncLink Device............................14

Connecting an Ultra*Link Device......................... 15

Connecting Power to the Controller..................... 15

Specifications....................................................... 15

Declarations......................................................... 16

About this Guide

This installation guide explains how to install the

AMS-9030 controller. Other related documents are:

• Planning Guide, 8200-0344-01

• Installation Guide, AMS-9030 Key Switch

Option Kit, 8200-0344-05

• Installation Guide, AMS-9030 Plenum Option

Kit, 8200-0344-06

• Setup and Service Guide, 8200-0344-08

• Reference Guide, 8200-0344-09

Note: Because customer requirements dictate the

placement of system components, your

Sensormatic representative will supply this

information separately.

Note to the Installer: If this product was installed

in a European Union or European Free Trade

Association member state, please give the

Declaration of Conformity included with this

product to the manager or user. By law, this

information must be provided to the user.

Note: There may be restrictions on the installation

of certain antennas in certain countries. Please see

the antenna installation guides for documentation

of the restriction.

Summary of content (16 pages)

PAGE 1
Preliminary AMS-9030 Controller About this Guide Installation Guide This installation guide explains how to install the AMS-9030 controller.
PAGE 2
Preliminary Controller Overview Installation Requirements ® An AMS-9030 controller is part of an Ultra•Max security label detector. The controller supports the following system components, some of which are shown in Figure 1: • Two transceiver antennas or two pairs of Tx/Rx antennas for tag and label detection. • One remote alarm (optional), but the controller supports two-alarm configurations with two internal relays.
PAGE 3
Preliminary Controller G The controller can be placed on a shelf or mounted on a wall. It can be hidden in a remote location such as a back room or basement. G Provide a minimum of 20cm (8") of unobstructed space around the controller for ventilation. G Use the appropriate power cord based on the country of use. USA-IEC 320, 18/3, 125V, 10A, 7.5ft. 0351-0547-01 Schuko-IEC 320, 1mm sq., 250V, 10A, 2.5m 0351-0547-02 UK-IEC 320, 1mm sq., 250V, 10A, 2.5m 0351-0547-03 Japan-IEC 320, 2mm sq.
PAGE 4
Preliminary 2. Drill holes into the wall and insert anchors. Note: The mounting method must be able to support 23.5 kg (52 lbs). Connecting Antennas Currently you can only connect Ultra*Post Pluscompatible antennas to the AMS-9030 controller. The controller contains some connectors reserved for future antennas. The table below shows where you connect the cables. Figure 5 shows the locations of the connectors. 3. Secure the mounting bracket to the controller using the four screws provided.
PAGE 5
Preliminary CAUTION: Do not connect ferrite receivers (for example, Rangers, Satellite receivers) to the transceiver connectors P13 and P16. They must only be connected to receiver ports P22 and P23. The following two tables show how to connect the +5V and +12V antennas; antennas without alarms do not connect to P15 and P18. Note that depending on how the controller motherboard has been configured, pin 3 provides either +5v or +12V for the antenna alarm lamp.
PAGE 6
Preliminary • Quad – a two-controller system with four antennas. Both controllers have two transceiver antennas connected to P13 and P16. If the antennas are near each other, a wired sync cable is required. Configurations The following list describes the basic ways that antennas can be configured with the controller. Figure 3 and Figure 4 show examples of these configurations. • Single – one transceiver (XCVR) antenna connects to P13 (A) or P16 (B).
PAGE 7
Preliminary Figure 3. Single and dual antenna configurations Single Single with one receiver Transceiver (XCVR) Tx Rx XCVR Rx Dual Single with two receivers Rx AMS-9030 CONTROLLER INSTALLATION GUIDE Rx Dual with two receivers Rx XCVR Tx XCVR Tx Rx Tx 8200-0344-02, REV.
PAGE 8
Preliminary Figure 4. Split, triple, and quad antenna configurations Split Tx Rx Tx Tx Split (or Triple) Rx Tx XCVR Triple with three receivers Rx Tx AMS-9030 CONTROLLER INSTALLATION GUIDE Rx Tx XCVR XCVR Quad Rx XCVR XCVR XCVR XCVR XCVR 8200-0344-02, REV.
PAGE 9
Preliminary Figure 5.
PAGE 10
Preliminary Figure 6.
PAGE 11
Preliminary Figure 7. Front of controller IEC320 Power connector Status LED AMS-9030 CONTROLLER INSTALLATION GUIDE Fuse holder SyncLink port Service port 8200-0344-02, REV.
PAGE 12
Preliminary 2. Connect the remote alarm to the Remote Alarm connector (P29) on the controller. Figure 6 shows the location of P29 and Figure 9 shows how to connect the remote alarm. Note that the black and red wires are connected to different pins than other controllers. Connecting Remote Alarms The AMS-9030 controller provides the power and control signals for a single remote alarm (ZC30ADS/ZC35-ADS) at P29. (This is the only powered alarm port.
PAGE 13
Preliminary Figure 10. Connecting a remote alarm to P20 Connecting Multiple 9030 Controllers Remote alarm (ZC30/ZC35) black } COM red 17V green Arm white N.O. silver Ground Trans If you install adjacent (within 1.1m (3.5’)) antennas former } P19/ P20 Table 6. Connecting remote alarm A Alarm Wire Connector Pin Signal Black Com 1 V Alarm Ret Red 17V 2 +V Alarm Green P19 1 A - Arm White P19 2 A – N.O.
PAGE 14
Preliminary Figure 11. Wired sync wiring diagram Connecting a Service Laptop Master Controller To use the configurator on your service laptop to configure the controller, connect your laptop to the female RJ22 port labeled “Service” on the controller. See Figure 7. 1 Sync signal P9 2 Ground You can also connect a service laptop remotely over a network. For information on connecting a laptop remotely, refer to the Setup and Service Guide.
PAGE 15
Preliminary Connecting an Ultra*Link Device Specifications Electrical Ultra*Link devices are connected to the controller at the Service port on the controller and at the COMM1 port on the Ultra*Link device. The location and pinout of the Service port is shown in Figure 1. Note: if the controller has an Ultra*Link device on its Service port, it cannot communicate with a laptop connected there or on an antenna. Power Supply Primary Input ....................................
PAGE 16
Preliminary Mechanical purpose. Further, Sensormatic Electronics Corporation reserves the right to revise this publication and make changes from time to time in the content hereof without obligation of Sensormatic Electronics Corporation to notify any person of such revision or changes. Controller Length ...............................................36.8cm (14.5") Width.................................................32.8cm (12.