User's Manual

ManualsBrandsTyco Safety Products/Sensormatic ManualsElectronicsANTI-PILFERAGE DEVICE

Table Of Contents

AMS-9040 Controller

AMS-9040 CONTROLLER 8200-0367-02, REV. E

INSTALLATION AND SERVICE GUIDE

1 of 22

AMS-9040 Controller

Installation and Service Guide

ZE9040, ZE9040-68K

Contents

To the Installer....................................................... 1

About the Product.................................................. 2

Basic Operation and Setup ................................... 2

Device Connections .............................................. 3

Installation Features.............................................. 7

Service Features ................................................... 8

Installation Requirements...................................... 9

Installation Procedure.......................................... 10

AC Hookup.......................................................... 12

System Setup...................................................... 14

Redistributing the Load ....................................... 15

Special Rules for Floor Antennas........................ 16

Troubleshooting................................................... 17

Fuse Replacement .............................................. 19

Specifications ...................................................... 20

Declarations ........................................................ 21

Appendix A: Auto Synchronization...................... 22

To the Installer

The AMS-9040 detection system consists of a

ZE9040 controller and the following antennas:

Non-European Installation

Antenna Type

Digital Euro Pro-Max 4 AMS-3003 System

Digital Pro-Max 4 AMS-3004 System

Digital Door-Max 4 AMS-3010 System

Digital Floor-Max 4 AMS-3030 System

AMS-3000 System AMS-3031 System

European Installation

Antenna Type

Digital Euro Pro-Max 4

Digital Pro-Max 4

Digital Door-Max 4

Digital Floor-Max 4

CAUTION: Ultra•Loop antennas cannot

be installed with the AMS-9040 controller

in EU countries.

This installation and service guide explains how to

install, setup, and service the AMS-9040 controller.

Parts required to install this system are:

• AMS-9040 Controller

• Digital AM intelligent antennas (various)

• AMS-9040 Service Configurator Software.

Other documents that may be required for

installation are:

• AMS-9040 Detection System Planning Guide,

8200-0367-01

• Antenna Installation Guide (various)

• AMS-9040 Controller Key Switch, 8200-0367-04

• AMS-9040/Digital 216 Controller

Air Handling Kit, 8000-2693-11.

Regulatory Restriction: In certain

countries, there may be installation

restrictions on the antennas. See antenna

installation guides for restrictions, if any.

Intended Use: Only install this device as

described in this guide.

Declaration of Conformity: If this product

was installed in a European Union or

European Free Trade Association member

state, give the Declaration of Conformity

included with this product to the manager or

user. By law, this information must be

provided to the user.

• Because customer requirements dictate the

placement of system components, your

Sensormatic representative will supply this

information separately.

• Because of the number of antennas and

accessories that can connect to this controller,

methodically install this system to avoid

problems. See “System Setup” in this guide for

guidance on how to setup antennas.

• Never restart or boot up a computer connected

to an active controller. Doing so disables the

mouse function on the computer.

Summary of content (22 pages)

PAGE 1
European Installation AMS-9040 Controller Antenna Type Digital Euro Pro-Max 4 Digital Pro-Max 4 Digital Door-Max 4 Digital Floor-Max 4 Installation and Service Guide CAUTION: Ultra•Loop antennas cannot be installed with the AMS-9040 controller in EU countries. This installation and service guide explains how to install, setup, and service the AMS-9040 controller.
PAGE 2
About the Product U-shaped opening for power cord Cable Tray The four-channel AMS-9040 controller is part of an EAS detector used to detect EAS tags/labels at store exit(s). Controller Features • Inputs for up to eight intelligent or non-intelligent antennas (four of which can be transceivers), up to four auxiliary receiver antennas, and up to four noise coils. Antenna coils can be set for phase flipping (default), aiding, or figure-8 operation.
PAGE 3
General-Purpose Auxiliary Connections (P27, P29, P31, P33) Device Connections Connector pin assignments are listed on pages 4 and 5.
PAGE 4
A label inside the controller identifies connectors. SERVICE (RS-232) (Behind Cover) Cables pass into enclosure through here.
PAGE 5
Continued from previous page REMOTE ALARMS (P7) Pin 1 - 12V Return (Alarm 0) Pin 2 - 12V (Alarm 0) Pin 3 - Alarm 0 Pin 4 - Shield (Alarm 0) Pin 5 - 12V Return (Alarm 1) Pin 6 - 12V (Alarm 1) Pin 7 - Alarm 1 Pin 8 - Shield (Alarm 1) RELAYS C-D (P12) Pin 1 - C (Relay C) Pin 2 - NC (Relay C) Pin 3 - NO (Relay C) Pin 4 - 'X' (Relay C shield) Pin 5 - C (Relay D) Pin 6 - NC (Relay D) Pin 7 - NO (Relay D) Pin 8 - 'X' (Relay D shield) WIRED Tx SYNC (P2) Pin 1 - Black (Tx burst high) Pin 2 - Red (Tx burst low) Pi
PAGE 6
Beacon Lamp Connections (P10) Wireless AC Sync Connection (On Controller) This connector controls up to two beacon lamps, and supplies up to 12V at 1A to power each lamp. Protected by a cover plate, this connector: • Receives a cable from a Sync Link device which, when connected, is used as the timing reference for system functions instead of ac synchronization. See “Automatic AC Line Synchronization” on page 7. Also, see Appendix A. • Can also be used instead to transmit the timing reference.
PAGE 7
Auto sync status is displayed on the service configurator. Installation Features Note: If a Sync Link device is connected to the controller, the controller uses its signal as the timing reference instead. The service configurator indicates that Sync Link is active. Installation features are as follows: • • • • Automatic detect and setup functions Controller-assisted antenna tuning Transmitter current control Shelf, wall, or ceiling mounting. See additional information in “Appendix A”.
PAGE 8
• Separate a problem into one of three categories: controller, environment, or the device connected to the controller, such as antennas or remote alarms. Note: If default settings are changed, you do not need to turn the controller off and on to store them. Mounting the Controller ! Do not mount controller with its fan or cable tray face up. Using the cable tray/mounting bracket assembly supplied, the controller can be mounted as follows: • On a shelf. • On a wall.
PAGE 9
CAUTION: A 10A, 2-pole, ganged disconnect device, which also provides short circuit and overload protection, and has a minimum 3mm open circuit clearance, in accordance with the National Electric Code and applicable local codes must be installed by a licensed electrician at a location readily accessible to the equipment. Installation Requirements Installer/Contractor • Have electrical work comply with the latest national electrical code, national fire code, and all applicable local codes and ordinances.
PAGE 10
People with Implanted Medical Devices Installation Procedure Although this anti-theft system complies with all applicable safety standards, place the system in such a way that customers: This section describes installation procedures for when the controller is to rest on a shelf, or attach to a wall or ceiling. • do not linger near or lean on its antenna(s) while making their purchase 1. Remove the cover from the top of the controller.
PAGE 11
4. If using cable clamps: Thread a clamp into each hole used. Run cables (except power) through clamps leaving about 30cm (1ft) of excess cable on the other side. Tighten clamps. 6. Mount the controller partially onto the mounting bracket and connect cables. a. Attach connectors supplied to the cables. b. Route cables through the rectangular opening in the controller housing. If using conduit: Attach conduit to the cable tray and run cables to the controller. c.
PAGE 12
Power Cord AC Hookup Referring to the figure below: Ac power connects to the controller using a power cord or hardwired cable. 1. Choose a power cord for the country of use. Power cords come in .9m (3ft), 2.7m (9ft), 3.7m (12ft), and 4.6m (15ft) lengths. • The power source can be 100-120Vac or 200-240Vac. 2. Route the power cord through the slot in the cable tray. • The controller automatically senses the voltage so no jumper settings are required.
PAGE 13
4. Plug the cord into the IEC320 receptacle in the controller housing. Hardwired Cable CAUTION: Use only copper wire. Referring to the figure below: 1. Remove one of the three knockouts accessing the ac connection area in the cable tray. Thread a cable clamp into the hole. 2. Route the ac cable through a cable clamp, leaving about 15.2cm (6in) out the other side. Tighten the clamp around the cable. IEC320 Receptacle 5. Plug the power cord into the ac outlet.
PAGE 14
PROCEDURE System Setup 1. Ensure the controller is off. The AMS-9040 controller requires field personnel to setup the controller for the environment. For a successful installation, follow the two rules below: 2. Connect antenna Tx/Rx cables to the controller according to how the antennas are intended to perform. If the antenna is intelligent, set the rotary switch on its cap board to match the address on the controller for the Rx input.
PAGE 15
3. Connect the communication cable from each intelligent Tx/Rx antenna to the communication connector associated with that antenna. Redistributing the Load The AMS-9040 system typically handles receiver multiplexing by assigning each antenna connected to the controller to a receiver channel. There are eight receive channels for up to eight antennas. 4. Turn on the laptop computer and bring up the AMS-9040 service configurator.
PAGE 16
Rule 2: When three Floor antennas are used in a Special Rules for Floor Antennas Follow these five rules for Floor-Max antennas: single doorway, cap boards for antennas A and B must share a single box, and a single key switch must control both antennas. The switch must connect to the lowest letter antenna. For example, for Floor antennas (A and B), connect the key switch to A. The cap board for antenna C will be in a box by itself with its own switch.
PAGE 17
Alert Codes Troubleshooting System Status Alert Codes The Status LED on the controller displays system status alert codes (also called error codes). When an alert code occurs, the LED changes color and pattern. Red is used for serious alerts while yellow is used for those less serious. • The number of yellow or red flashes identifies a digit in a two-digit alert code (for example, four flashes is the number four). The start of an alert code is indicated by a long LED interval.
PAGE 18
Controller-Assisted Tuning cannot be Performed Local Diagnostics You can troubleshoot and change controller parameters using your laptop computer and AMS-9040 service configurator software. If controller-assisted tuning cannot be performed, a message indicating the cause is posted on the service configurator.
PAGE 19
Remote Diagnostics Fuse Replacement The AMS-9040 controller enables you to use an RS-485 network to troubleshoot and adjust the controller from a remote site. To connect to the network, connect the laptop, modem and accessories as shown below. The controller contains two 5A, 250V, slow-blow fuses. To replace the fuse(s) in the controller, do the following: Fuses (2) Laptop Modem DB-25 male to DB-9 male adapter Null modem adapter RS-232/RS-485 converter 1. Detach the controller from the cable tray.
PAGE 20
Environmental Specifications Ambient temperature................ 0°C to 50°C (32°F to 122°F) Electrical Relative humidity...................... 0 to 90% non-condensing Power Supply Primary input ............................100-120Vac or 200-240Vac @ 50–60Hz Mechanical Primary power fuse...................5A, 250V, slo-blow, hi-breaking Length ...................................... 50.8cm (20in) Current draw.............................4.0Arms @ 120Vac Width without bracket............... 32.
PAGE 21
Regulatory Compliance FCC COMPLIANCE: This equipment complies with Part 15 of the FCC rules for intentional radiators and Class A digital devices when installed and used in accordance with the instruction manual. Following these rules provides reasonable protection against harmful interference from equipment operated in a commercial area.
PAGE 22
Appendix A: Auto Synchronization Auto synchronization occurs during power up or system reset. Auto sync can have four different outcomes depending on whether nearby EAS transmitters are detected, they are properly aligned to the ac-derived timing of the controller, or too much ambient noise exists. No transmitters detected. During initialization, the controller determines if EAS transmitters are nearby.