User's Manual

ManualsBrandsTyco Safety Products/Sensormatic ManualsElectronicsANTI-PILFERAGE DEVICE

Preliminary

AMS-9060 CONTROLLER 8200-1014-01, REV. 1A

INSTALLATION GUIDE

1 of 13

AMS-9060 Controller

Installation Guide

ZE9060

ZE9060-2C

TYPE: AMS-9060

Contents

AMS-9060 Controller ............................................. 1

About this Guide .................................................... 1

To the Installer ....................................................... 1

About the Product .................................................. 2

Installation Requirements ...................................... 3

Controller Installation ............................................. 4

Specifications ...................................................... 12

Declarations ........................................................ 12

About this Guide

This installation and setup guide explains how to

install the AMS-9060 controller.

At least one but no more than four of the hybrid

series-parallel versions of the following antennas

can be connected to this controller:

 Ultra•Exit (AMS-1090 Series / AMS-1100 Series)

 Pro-Max 5

Options that connect to this controller are:

 AMS-1060 digital remote alarm

 Passive relays

 Noise canceling antennas

 Wired synchronization

 CBC-4020-216 (UltraLink) or CBC-4055 (LDM II).

Other documents that may be required for

installation are:

 AMS-9060 Planning Guide, 8200-1014-02

 Pro-Max 5 Pedestals Installation Guide, 8200-1014-

 Ultra•Exit Transceiver Antennas Installation Guide

(AMS-1090/AMS-1100 Series), 8200-0537-16

 AMC-1060 Digital Remote Alarm Installation Guide,

8200-0505-01

 CBC-4055 Local Device Manager II Installation

Guide, 8200-0858-01

 Wired Sync Hookup Installation Guide, 8200-0537-

07.

To the Installer

Regulatory Restriction: In certain

countries, there may be installation

restrictions on the antennas. See antenna

installation guides for restrictions, if any.

Regulatory Restriction: Except for

power input connector all connections are

class 2.

Regulatory Restriction: For indoor use

only.

Intended Use: Only install this device as

described in this guide.

Declaration of Conformity: If this

product was installed in a European

Union or European Free Trade

Association member state, give the

Declaration of Conformity included with

this product to the manager or user. By

law, this information must be provided to

the user.

 Because customer requirements dictate the

placement of system components, your

Sensormatic representative will supply this

information separately.

 Because of the number of antennas and

accessories that can connect to this controller,

methodically install this system to avoid

problems. See “Connecting Pedestals” in this

guide for guidance on how to setup antennas.

Do Not Discard!

This document may be needed by code inspectors.

Leave it at the site until the installation is complete and

the system has been approved.

Summary of content (13 pages)

PAGE 1
Do Not Discard! This document may be needed by code inspectors. Preliminary Leave it at the site until the installation is complete and the system has been approved. AMS-9060 Controller Other documents that may be required for installation are: Installation Guide       ZE9060 ZE9060-2C TYPE: AMS-9060 To the Installer Regulatory Restriction: In certain countries, there may be installation restrictions on the antennas. See antenna installation guides for restrictions, if any.
PAGE 2
Preliminary No transmitters detected. During initialization, the controller determines if EAS transmitters are nearby. If none are found, transmitter delay is set to zero at initial power on, or set to the value stored in the controller if not the initial power on. About the Product The AMS-9060 controller is part of an EAS system that:  Includes Ultra•Exit or Pro-Max 5 antennas used to detect tags/labels at exits or in food store checkout aisles.
PAGE 3
Preliminary WARNING! This device is not suitable for an IT power distribution system where impedance exists between neutral and protective earth contacts. Installation Requirements Verifying Equipment and Unpacking  Verify that all equipment has arrived. Ensure the system configuration is correct for the site. CAUTION: When using a power cord, install a socket-outlet near the controller in an easily accessible location.
PAGE 4
Preliminary Implanted Medical Devices Controller Installation This anti-theft system complies with all applicable safety standards. However, people with implanted electronic medical devices may ask if the store has an anti-theft system and its location. Although most anti-theft systems are easily seen, some can be concealed.
PAGE 5
Preliminary WARNING—RISK OF ELECTRIC SHOCK! The ac power cord may carry 120Vac or 240Vac. Connecting AC Power The controller can receive AC power either through a power cord or through a hardwired connection. CAUTION: When using a power cord, a socket-outlet must be installed near the controller and in an easily accessible location.
PAGE 6
Preliminary 6. Remove one of the knockouts accessing the ac connection area. Thread a cable clamp into the hole. Connecting Pedestals Transceiver pedestals connect to the AMS-9060 controller with two cables: Transceiver (Tx/RX) cables and Alarm/Communication cables. They connect to the controller at the following connectors: 7. Route the ac cable through a cable clamp, leaving about 15.2cm (6in) out the other side. Tighten the clamp around the cable. 8.
PAGE 7
Preliminary  To accept a noise canceling coil, the auxiliary input must be in noise canceling mode (set using service configurator software). Save adjustments to default settings if they are to be used on the next power cycle or system reset.
PAGE 8
Preliminary Figure 1.
PAGE 9
Preliminary Table 1. Exit System Note: Numbers 1, 2, 3, and 4 under mode column indicate the pedestals used. 1-2_3-4 indicates that 1 and 2 pedestals are in one exit, and 3 and 4 pedestals are in another. 1-2-3-4 indicates all pedestals are in one exit. Note: Disregard receiver settings when using antennas as transceivers. EXIT SYSTEM MODE Exit 1 Exit 2 PED 1 Connections PED 2 Connections PED 3 Connections PED 4 Connections Auto Config.
PAGE 10
Preliminary Setting Dip Switches Connecting Optional Devices IMPORTANT! DIP S1 and DIP S2 are located on the circuit board of the controller. When connecting antennas, set switches 1–8 of each DIP according to the number and type of antennas used. Connect any optional devices to their connectors.
PAGE 11
Preliminary Configuring the System Verifying Operation The AMS-9060 controller enables you to change controller parameters using your laptop computer and the ADS 4 service configurator. 1. Pass an active security tag by each antenna to verify antenna performance. Refer to Help if monitoring or adjustments are necessary. 2.
PAGE 12
Preliminary Specifications Declarations Electrical TYPE: AMS-9060 Model: AMS-9060 (4 channel controller) Model: AMS-9060-2C (2 channel controller) Power Supply Primary input ........................................... 100-120Vac or 220-240Vac @ 50–60Hz Primary power fuse ...................... 3.15A, 250V, slo-blow, hi-breaking Current draw (120V) ........................................ <2.1Arms Current draw (240V) ........................................ <0.9Arms Input power (120V) ..................
PAGE 13
Preliminary EQUIPMENT MODIFICATION CAUTION: Equipment changes or modifications not expressly approved by Sensormatic Electronics, LLC, the party responsible for FCC compliance, could void the user's authority to operate the equipment and could create a hazardous condition. See “About the Product” on page 2.