User's Manual

ManualsBrandsTyco Safety Products/Sensormatic ManualsElectronicsAnti-Theft Auxiliary Device

Preliminary

AMC-4010 SYNCHRONIZATION MODULE INSTALLATION AND SERVICE GUIDE (8200-0183-01, REV. 03)

1 of 5

ZPSYNC4010 Wireless ZPSYNC4010 Wireless

Sychronization Sychronization

ModulesModules

Setup GuideSetup Guide

Wireless synchronization modules can significantly

reduce electrical interference between Sensormatic

EAS systems timed to the AC line. A module

system includes a module designated as a

transmitter and one or more modules designated

as receivers.

IMPORTANT! Ensure EAS devices can support

wireless synchronization.

IMPORTANT! The maximum distance between the

transmit module and any receive module is

approximately 60.1m (200 feet), but keep in mind

that the range depends upon the environment in

which the module is used. Many factors can limit

the range, thus it would be impossible to list them.

For best performance, please follow these

instructions carefully.

Parts SuppliedParts Supplied

Sync Link Module 1 0304-0029-01

Cable Ties 3 ?

Cable 1 ?

Mechanical SpecificationsMechanical Specifications

Dimensions: 82mm (L) x 60mm (W) x 30mm (D)

Weight: 2.5 oz

Transmit FrequenciesTransmit Frequencies

North America Frequency Hop: 903.2–914.8 MHz

Europe Single Low frequency: 869.8 MHz

Europe Single High frequency: 869.9 MHz

Setting Up the TransmitterSetting Up the Transmitter

1. Find the EAS device that is central and within

60.1m (200 feet) of the others. Designate this

device for use with the transmit module.

IMPORTANT! DO NOT designate a mobile

checkout stand or use with the transmit

module. Only receive modules can be used

with mobile checkout stands.

2. Configure one module as the transmitter by

opening it and setting switch 7 to OFF (see

Table on page 3). To access the switch,

remove the holding screw and carefully

separate the top and bottom covers (the side

label serves as a hinge between the two

covers. DO NOT remove this label).

Summary of content (5 pages)

PAGE 1
Preliminary For best performance, please follow these instructions carefully. ZPSYNC4010 Wireless Sychronization Parts Supplied Sync Link Module Cable Ties Cable Modules Setup Guide 1 3 1 0304-0029-01 ? ? Mechanical Specifications Dimensions: 82mm (L) x 60mm (W) x 30mm (D) Weight: 2.5 oz Transmit Frequencies North America Frequency Hop: 903.2–914.8 MHz Europe Single Low frequency: 869.8 MHz Europe Single High frequency: 869.9 MHz Setting Up the Transmitter 1.
PAGE 2
Preliminary 5. Mount the transmit module: • IMPORTANT! Ensure the module will be within 60.1m (200 feet) of the transmit module. Switch 7 4. As high as possible and in a location near the designated EAS device. The length of the cable supplied determines the distance the module can be from the device. • In such a way that the two LEDs on the module can be readily see from below.
PAGE 3
Preliminary Setting Up a Receiver 1. Verifying Operation Mount each receive module: • Transmit Module As high as possible and in a location near the designated EAS device. The length of the cable supplied determines the distance the module can be from the device. Look at the transmit module. The green LED blinking with the red LED off is normal. Receiver Module(s) IMPORTANT! Ensure the module will be within 60.1m (200 feet) of the transmit module. Look at each receive module.
PAGE 4
Preliminary Receive Receive Module(s) Troubleshooting If the red LED is glowing steadily or flickering, this indicates that the module is either not receiving a signal from the transmit module or the signal is weak. Try moving the receiver 15.5 cm (6 inches) up or down the pole to allow it to receive a stronger signal. Transmit Module If the red LED is blinking, this means that the power line connected to the EAS device it is connected to has noise on it.
PAGE 5
Preliminary Other Declarations Declarations WARRANTY DISCLAIMER: Sensormatic Electronics Corporation makes no representation or warranty with respect to the contents hereof and specifically disclaims any implied warranties of merchantability or fitness for any particular purpose.