User's Manual

ManualsBrandsTyco Safety Products/Sensormatic ManualsElectronicsRFID READER

AGILE2 READER 8200-0222-08, REV. A

INSTALLATION AND SERVICE GUIDE

1 of 13

Agile2 Reader

Installation and Service Guide

IDRDR2A4UNA 4 Port UHF NA

IDRDR2A8UNA 8 Port UHF NA

IDRDR2B2UNA 2 Port UHF - NA 1/0

IDRDR2B4UNA 4 Port UHF - NA 1/0

The Agile2 Reader uses RFID (radio frequency

identification) technology to read data stored on

RFID tags and labels. The reader operates as an

SQL (structured query language) server, providing

tag data in response to requests from another

application. A separate software application may

be used to direct its operation and provide a user

interface.

The reader supports UHF (ultra high frequency)

antennas, which are available separately. The

reader supports multiple configurations of UHF

antenna ports and transfers data to a remote

computer either through a wired 10/100 Ethernet

connection.

The content of this document was developed by

ThingMagic LLC.

If you need assistance...

Call the RFID support line at 800-543-9740.

Contents

About this Guide.............................................................1

Before You Begin ...........................................................2

Installation Requirements........................................2

Performance Considerations...................................2

Product Configurations and Part Numbers.....................3

Authorized Antennas......................................................3

Reader Installation .........................................................4

Install the Reader....................................................4

Install the Antennas ................................................4

Connect the Reader................................................4

Antenna Connection Options ..................................5

Configure the Reader..............................................6

Service ...........................................................................7

Using the Browser-Based Interface ........................7

Rebooting the Reader...........................................11

Using Safe Mode ..................................................11

Specifications ...............................................................12

Declarations .................................................................13

About this Guide

This installation and service guide explains how to

install the Agile2 Reader and use the browser-

based interface.

Use the instructions provided with the antennas to

install and service the antennas.

Other related Agile2 Reader documents are:

• Regulatory Information for the User,

8200-0222-16

• Query Protocol Reference Guide,

8200-0222-09

• Industrial Enclosure Installation Guide,

8200-0222-11

Antenna Documents:

• OmniPoint Antenna Mounting Instructions,

8200-0314-02

• OmniWave Antenna Mounting Instructions,

8200-0314-03

Note: Because customer requirements dictate the

placement of reader and antenna components,

your Sensormatic representative will supply this

information separately.

Summary of content (13 pages)

PAGE 1
Contents Agile2 Reader About this Guide.............................................................1 Before You Begin ...........................................................2 Installation Requirements........................................2 Performance Considerations...................................2 Product Configurations and Part Numbers.....................3 Authorized Antennas......................................................3 Reader Installation ...........................................
PAGE 2
Tag Variables Before You Begin There are several variables associated with tags that can affect reader performance: Installation Requirements • The reader is shipped with a certified limited power source with a cable length of 1.8m (6ft). • Use only authorized antennas and cables to maintain FCC approval (see Product Configurations and Part Numbers on page 3).
PAGE 3
Product Configurations and Part Numbers Agile2 Reader Description / Part Number Analog Addressable Modules Read Points Protocol Support Class 1 Class 0 ISO 18000-6B UHF 4-Readpoint IDRDR2A4UNA 1 4 Yes Yes UHF 8-Readpoint IDRDR2A8UNA 2 8 Yes Yes UHF 2-Readpoint IDRDR2B2UNA 1 2 Yes Yes Yes UHF 4-Readpoint IDRDR2B4UNA 2 4 Yes Yes Yes Authorized Antennas IDANT10CNA25 OmniWave Antenna CAUTION: Use only 7.6m (25ft) cables (0652-0147-02) with the OmniPoint and OmniWave antennas.
PAGE 4
Install the Antennas Reader Installation The antennas can be mounted directly to a variety of surfaces. Follow the installation instructions provided with the antennas. The following parts are provided with the reader: Part Qty.
PAGE 5
4. Plug the transformer provided with the reader into the DC power input connector. Then connect the transformer to a power outlet. While the reader is powering up, one green, one yellow, and one red light will be on. After approximately 30 seconds, all lights except the green one should go out; the green light will blink after the reader finishes its power-on selftest. The reader is now ready for operation.
PAGE 6
Configure the Reader IMPORTANT: Do not disconnect power until the save process is complete. In some cases, the application software may provide support for reader configuration. If so, follow the instructions provided with the application. 7. Verify that the settings shown are correct. Then, restart the reader by disconnecting the power cable and then reconnecting it (see Rebooting the Reader on page 11).
PAGE 7
Service Using the Browser-Based Interface Navigation menu The Agile2 Reader tag reader browser-based interface communicates directly with the RFID reader. It includes several tools that let you monitor reader performance, change reader settings, and upgrade reader firmware. A navigation menu provides access to the following pages: Status Page The Agile2 Reader Status page shows the current settings of the reader. • Status—displays basic operational settings.
PAGE 8
• Bignum checkbox (when checked) displays the total number of unique tags read. The total is displayed in large red numbers directly over the tags read list. Operating mode pull-down list The following operating modes are available for use with the Query page: Selection Description • Show Raw button changes the tag data display into a hexadecimal format and changes the button to Hide Raw.
PAGE 9
Write Page To read data from a tag: Use the Write page to replace the EPC data that is encoded on a 915 MHz EPC Class 1 tag. 1. Display the Write page (click the Write link on the navigation menu). 2. Click the Make Select button. A query designed to read data from the antenna connected to UHF1 appears in the center pane. 3. Place the tag to be read within the detection zone of the antenna. 4. Click the Submit Query button to read tag data. Query results appear in the bottom pane.
PAGE 10
Firmware Upgrade Page Instructions for Modifying the Settings Changing these parameters changes the values used on startup. The set of variables that can be changed affects both the network settings and radio settings. Even though basic validity checking is performed, care must be taken to use correct values.
PAGE 11
Diagnostics Page Help Page The diagnostics page provides a wealth of information including the current settings of the reader, comprehensive version information, and current status of network interfaces. Use the Help page to view descriptions of system operations. Rebooting the Reader Use this procedure to recover from a reader error. 1. Disconnect power from the reader. 2. Re-connect reader power. Wait for at least 60 seconds for the reader to boot up.
PAGE 12
Although the browser-based interface pages are displayed in red when operating in Safe mode, the reader is fully functional. In most cases, the reader will need to be reconfigured for operation with the reader application after starting in Safe mode. Specifications Electrical Reader UHF operating frequency....................902–928MHz Input voltage ........................................ 24Vdc, 3.0A 1. Disconnect power from the reader. 2.
PAGE 13
Declarations Regulatory Compliance EMC............................................... 47 CFR, Part 15 RSS210 Safety .......................................................UL 60950 Can/CSA C22.2 No 60950 EN 60950 FCC COMPLIANCE: This equipment complies with Part 15 of the FCC rules for intentional radiators and Class A digital devices when installed and used in accordance with the instruction manual.