Fire 4100U Fire Indicator Panel Fire Alarm System, Installation & Maintenance Australian Australian Installation & Installation Maintenance Manual Manual LT0350
Copyrights and Trademarks 2004 Tyco Safety Products Westminster, Westminster, MA 01441-0001 USA. All specifications and other information shown were current as of document revision date, and are subject to change without notice. Tyco, Simplex, the Simplex logo, MAPNET II, IDNet, TrueAlarm, SmartSync, WALKTEST, MINIPLEX, and TrueAlert are trademarks of Tyco International Services AG or its affiliates in the U.S. and/or other countries. VESDA is a trademark of Vision Products Pty Ltd.
Non-Disclosure Agreement Tyco (THE COMPANY) and the User of this/these document(s) desire to share proprietary technical information concerning electronic systems. For this reason the company is disclosing to the User information in the form of this/these document(s).
Model Number & Firmware Revision This manual applies to product with the following: Model number : 4100U Firmware revision : 11.08 and on Document Document Name : LT0350 4100U Installation & Maintenance Manual Cross Reference : 574-848 4100U Installation Manual (USA) Issue : 1.0-G 14 May, 2004 Amendment Log 14 May, 2004 Issue 1.0.
Cautions, Warnings, and Regulatory Information READ AND SAVE THESE INSTRUCTIONS. Follow the instructions in this installation manual. These instructions must be followed to avoid damage to this product and associated equipment. Product operation and reliability depends upon proper installation. DO NOT INSTALL ANY SIMPLEX® PRODUCT THAT APPEARS DAMAGED. Upon unpacking your Simplex product, inspect the contents of the carton for shipping damage.
Table of Contents Copyrights and Trademarks ................................................................................ i Approvals............................................................................................................. i Manufacture......................................................................................................... i Product / Site .......................................................................................................
4100U PIDs ..................................................................................................... 1-9 Overview...................................................................................................... 1-9 Assemblies, Cards & & Modules ................................................................. 1-9 Kits ............................................................................................................. 1-10 Labels .....................................................
Step 6. Installing LED/Switch Modules into Expansion Bays (4100U).......... 2-20 Overview.................................................................................................... 2-20 The LED/Switch User Interface ................................................................. 2-21 LED/Switch Controller Card.......................................................................2-21 LED/Switch Modules..................................................................................
Local Mode Specifications ........................................................................... 4-5 LEDs ............................................................................................................4-6 Card Specifications...................................................................................... 4-6 MINIPLEX System Guidelines (4100U)........................................................... 4-7 Overview.........................................................................
Wiring Illustrations ..................................................................................... 5-17 Wired Media, Style 7 Wiring .....................................................................5-17 Fiber Optic, Style 7 Wiring ........................................................................ 5-18 Wired Media and Fiber Optic, Style 7 Wiring............................................ 5-19 Chapter 6 The System Power Supply & Alarm Relay Card..... 6-1 Introduction .......................
SPS Auxiliary Power Wiring ............................................................................ 7-8 Overview...................................................................................................... 7-8 Guidelines.................................................................................................... 7-8 Wiring........................................................................................................... 7-9 SPS Relay Wiring .......................................
Chapter 9 PC Software Connections ........................................ 9-1 Introduction .................................................................................................. 9-1 In this Chapter ............................................................................................. 9-1 Software Modes............................................................................................... 9-2 Overview.................................................................................
Appendix A The Device Configuration DIP Switch..................A-1 Overview......................................................................................................A-1 Appendix B Programming Requirements ................................B-1 Introduction ..................................................................................................B-1 In this Chapter .............................................................................................B-1 Required Features ...........
Appendix G Compatible Batteries............................................ G-1 Appendix H 4100U Specifications.............................................H-1 General ....................................................................................................... H-1 Fuses .......................................................................................................... H-1 Firmware Features......................................................................................
List of Figures Figure 1-1. Figure 1-2. Figure 1-3. Figure 1-4. Figure 2-1. Figure 2-2. Figure 2-3. Figure 2-4. Figure 2-5. Figure 2-6. Figure 2-7. Figure 2-8. Figure 2-9. Figure 2-10. Figure 2-11. Figure 2-12. Figure 2-13. Figure 2-14. Figure 2-15. Figure 2-16. Figure 2-17. Figure 2-18. Figure 2-19. Figure 2-20. Figure 3-1. Figure 3-2. Figure 3-3. Figure 3-4. Figure 3-5. Figure 3-6. Figure 3-7. Figure 4-1. Figure 4-2. Figure 4-3. Figure 4-5. Figure 5-1. Figure 5-2. Figure 5-3. Figure 5-4. Figure 5-5.
Figure 8-2. Figure 8-3. Figure 8-4. Figure 8-5. Figure 8-6. Figure 9-1. Figure 9-2. Figure 9-3. Figure 10-1. Figure D-1. Figure G-1. Mounting onto the Power Distribution Interface......................... 8-4 Mounting into 4100 (legacy) Bay ............................................... 8-5 DIP Switch SW1......................................................................... 8-6 Class A Wiring ........................................................................... 8-8 Class B Wiring ................
xvi
Chapter 1 Introduction to the 4100U Fire Alarm System Introduction The 4100/4100U is an expandable fire alarm system that can be used as a standalone system with one host panel, or as a wide-ranging system with several remote cabinets, with or without multiple host panels. This chapter is an overview of standalone, MINIPLEX, and network 4100 system concepts. In this Chapter Refer to the page number listed in this table for information on a specific topic.
System Configurations Overview The 4100U is available as a standalone system with one host panel, or as an expansive system with several remote back boxes, with or without multiple host panels. The type of configuration used depends on the size of the site into which it is being installed. The following types of configurations are offered: Standalone. Comprised of one FACP and its assorted warning devices, initiating devices, and signaling line circuit devices. MINIPLEX.
Standalone Configuration Overview The standalone version of the 4100U is used for smaller or single-building applications. A standalone system is ideally placed into a small building that requires a limited number of notification appliances and initiating devices. If a small building is being expanded, or if other buildings are being constructed in the same general area (as in a campus application), the standalone 4100U can be expanded into one of the larger systems described later.
MINIPLEX Configuration Overview The MINIPLEX version of the 4100 Fire Alarm System, which is designed for moderately larger applications than the standalone configuration, allows up to 1000 monitor and/or control points and 2000 annunciator points to be controlled by a single FACP. Like the standalone system, only one CPU is used. Remote Unit Interface (RUI) data, and optionally power is distributed from the host panel to remote boxes called transponder cabinets.
MINIPLEX Configuration, Continued RUI Communication The 4100 internal comms bus may be used to carry data from the CPU in the main cabinet to expansion equipment in a co-located cabinet. 4100 data from the CPU may be routed to remote cabinets (RTUs) in a MINIPLEX system by using the external RUI comms bus. An RUI line, routed from either the CPU Motherboard in the 4100U, or the RUI card in the 4100, allows the data to travel long distances.
Network Configuration Overview The 4100 can be expanded to a network system by using network interface cards (NICs). When a NIC is installed into a 4100 host panel, it is used to connect to other network nodes. Nodes may consist of other host 4100 panels, or they may be completely different: Graphical Command Centers (GCCs), and Visual Command Centers (VCCs) are all examples of what could be used as nodes.
Network Configuration, Continued Connecting Loops Network loops can be joined via physical bridge cards. There may be no more than two Style 7 network loops (two hub configurations) connected in tandem. For every two loops that are interconnected (using one physical bridge), there can be a maximum of three physical bridges used in a star configuration. See Figure 1-4.
4100 PIDs (Non-4100U) The following is a list of existing 4100+/A cards and modules that may be used with 4100U.
4100U Cabinet Part Identification Numbers (PIDs) Overview This section lists all cabinet (back box) PIDs for the 4100U Fire Alarm System.
4100U PIDs, Continued Kits • 4100-0625 Transponder Interface Card • 4100-0160 Internet Interface Module (566-355). • 4100-9848AU System Power Supply, Australian version.
Chapter 2 Installing 4100U FACP Components Introduction 4100U cabinets are available in one-, two-, and three-bay sizes. Each can be equipped with a solid or perspex door. This chapter describes how to mount all types of 4100U cabinets to a wall, and how to mount system card bays into the cabinets, modules to bays, etc. FACPs are assembled to order within the factory. Steps 2 to 6 below are therefore not typically required in the field, but are included in case of in-field system expansion.
Introduction to FACPs (4100U) Overview 4100U FACPs cabinets contain the CPU, operator interface, system power supply (SPS), backup batteries, and any additional modules that the panel requires. The FACP is the central hub (often referred to as a host panel) of a standalone or MINIPLEX fire alarm system. In a networked system, the FACP can be connected to other system FACPs, so that each host panel is a node on the network.
Introduction to FACPs (4100U), Continued Master Motherboard The 4100U Master motherboard that houses the CPU card is central to the 4100U system. It mounts in the first bay, occupying four inches of space on the right hand side. Neither has a card address DIP switch (the CPU is address 0).
Introduction to FACPs (4100U), Continued Master Controller Daughter Card The master controller daughter card mounts onto the master motherboard. The master controller daughter card contains a service port, a direct drive user interface connection, and a port for a service modem.
Introduction to FACPs (4100U), Continued Master Controller Daughter Card LEDs The master controller daughter card LEDs indicate Bootloader status as shown in the table below. Table 2-1. Master Controller LEDs 1 through 4 Status Condition LED4 LED3 LED2 LED1 On (0.25s), Off (0.25s) On (0.25s), Off (0.25s) On (0.25s), Off (0.25s) On (0.25s), Off (0.
Introduction to FACPs (4100U), Continued Operator Interface The operator interface lets a user operate the panel. It provides alarm, trouble, and isolate status alerts, and lets the user review historical logs and perform diagnostics. Figure 2-3. Operator Interface Additional CPU Bay Modules The CPU bay can be equipped with many additional types of modules. The cards listed below are limited to the CPU bay only. 4100-6030 Service Modem Card. CPU mezzanine card.
Introduction to FACPs (4100U), Continued System Power Supply (SPS) In the USA, a number of variants of power supply are available, e.g. SPS, RPS, XPS, XCharger each with different portions of circuitry (eg NACs, Battery Charger, IDNet) fitted or not fitted. In Australia, only one variant (SPS) is currently available, and it has hardware and software that are specific to Australia. This unit is used as the main power supply, but may also be fitted directly to a card bay as an expansion supply.
Introduction to FACPs (4100U), Continued System Power The FACP is powered by the SPS (System Power Supply), which gets its primary power from the AC mains and its secondary power from the backup batteries. The 24Vdc bulk power on the SPS is unregulated, and is divided into three feeds, i.e. 24V Card, 24V Signal, and 24V Aux Power. 24V Card which supplies the cards, and Aux power, which is accessible on screw terminals, are each rated at 2A and protected by a PTC. The 27.
Step 1. Mounting Cabinets (4100U) Overview The important aspects of mounting the cabinet are: Access for the operator; Height of displays and controls; Free space for door opening; Cable entry for field wiring. Refer to AS1670 for the height requirement and minimum access requirements. In general, 18U – 28U cabinets will need to be wall mounted. Mounting holes and cabinet dimensions are shown in drawing 1919-22b. Door opening left/right should be specified with the order.
Step 3. Configuring Cards (4100U) Overview The CPU, SPS, and all other modules to be mounted in the FACP cabinets must be configured to operate correctly in the system via their DIP switch and jumper ports. This section describes the hardware configuration for the CPU and SPS, since they will always be used in the CPU bay. Master Motherboard Configuration The CPU motherboard must be jumpered as follows: P9 determines whether the RUI SHIELD signal is connected to 24 C or Earth.
Step 3. Configuring Cards (4100U), Continued PDI Configuration P4/P5: The PDI can be configured to draw its power from different sources via P4 and P5. • To draw power from an XPS on the PDI, set jumpers on P4 and P5 to position 2 – 3. • To draw power from P1 (from the previous PDI or SPS), set jumpers on P4 and P5 to position 1 – 2 (default). • To remove power from the PDI, remove the jumper from P4.
Step 4. Interconnecting Modules and Bays, Continued Card Interconnections in the CPU Bay Card Interconnections Within Expansion Bays Basic Bay-To-Bay Interconnections Use the following directions to connect the CPU to the SPS and other motherboards. 1. Connect P3 on the SPS to P1 on the CPU motherboard using the 8 wire harness with eight-position Molex minifit connector (provided). 2.
Step 4. Interconnecting Modules and Bays, Continued Basic Bay-To-Bay Interconnections (continued) Figure 2-7, below, shows the interconnections between three bays in a host panel. From Previous PDI P1 HARNESS 734-008 4100 POWER DISTRIBUTION INTERFACE ASSY 566-084 P2 P3 P4 P5 P6 P7 P3 P1 4100 POWER DISTRIBUTION INTERFACE ASSY 566-084 P2 P3 P4 P5 P6 P7 Figure 2-7.
Step 4. Interconnecting Modules and Bays, Continued Connecting to Motherboards (continued) 2. Connect the other end of the harness to the leftmost motherboard in the next bay, as described below. Make sure to route the wiring on the left side of the bay. • Insert the harness connector with the blue wire into the P2 connector. Note that the P2 connector has eight pins. Insert the harness connector on either the top four pins or the bottom four pins, not in the middle.
Step 5. Installing Modules into Expansion Bays (4100U) Overview This section contains guidelines and instructions on installing 4”x 5” cards and traditional motherboards into 4100U card bays. IMPORTANT: This section applies to aftermarket modules for expansion bays only. If you do not need to install any aftermarket modules at all, and if you have followed Steps 1 through 6, you have completed the panel installation and can apply AC power.
Step 5. Installing Modules into Expansion Bays (4100U), Continued • Up to eight 2” (51 mm) x 11 ½” (292 mm) motherboards can be installed in an expansion bay if no 4”x 5”modules are installed in the bay, and if the pins on the left connector (usually P1) on the leftmost motherboard are removed. Motherboards are mounted on top of the PDI in expansion bays. The data and power that would normally be bussed via the PDI is instead routed across the boards via ribbon cable from one board to the next.
Step 5. Installing Modules into Expansion Bays (4100U), Continued As shown in the figure below, motherboards can be installed alongside 4”x 5” cards, if necessary.
Step 5. Installing Modules into Expansion Bays (4100U), Continued Installing 4” X 5” Cards The power distribution interface (PDI) is mounted to the back of each expansion cabinet. The PDI contains slots for up to eight 4”x 5” slave cards. Since the PDI carries power and data across the entire bay, it solves most interconnection issues, especially between 4”x 5” cards. Use the following instructions and the figure below to mount 4”x 5” slave cards to an expansion cabinet. 1.
Step 5. Installing Modules into Expansion Bays (4100U), Continued Installing Motherboards Use the following procedure when installing motherboards in an expansion bay. Start with the second slot from the left and fill to the right. The mounting items are available as KT0468. 1. Orient the motherboard with the connector labeled J1 on the right and the header labeled P1 on the left. 2. Attach four metal threaded standoffs and lockwashers into the screw holes on the chassis. 3.
Step 6. Installing LED/Switch Modules into Expansion Bays (4100U) Overview The LED/switch user interface consists of a variety of modules, mounted to the front of an expansion bay, which are configured via the 4100 Programmer. Each display module contains between 8 and 24 switches and LEDs, each one separately configurable. User interface functionality is driven by the 64/64 LED/Switch Controller Card, which mounts behind two of the display modules (typically in positions 3 and 4).
Step 6. Installing LED/Switch Modules into Expansion Bays (4100U), Continued The LED/Switch User Interface Below is an illustration of a LED/switch bay from the user’s perspective. Figure 2-14. LED/Switch Modules The LED/switch controller card is a 4100 slave that mounts behind two LED/switch modules. The LED/switch controller handles up to 64 switches and 64 LEDs on the modules and communicates their status to the 4100 CPU.
Step 6. Installing LED/Switch Modules into Expansion Bays (4100U), Continued LED/Switch Controller Card, (continued) If more than 64 LEDs or 64 switches are used, a second controller may be installed. LED/Switch Modules All types of modules are mounted to the front of a bay, and are connected to each other via a ribbon cable. Each module operates by the same rules: when a button is pressed, the controller card sends the CPU the information, and the event programmed for that button occurs.
Step 6. Installing LED/Switch Modules into Expansion Bays (4100U), Continued Mounting LED/Switch Modules to the Expansion Bay Refer to the figure below to mount the display cards to the front of the expansion box. #6 UNC NUTS ADDITIONAL LED/SWITCH CONTROLLER LOCKWASHERS GROUND CONNECTION Controller assemblies can only be installed into these two slots GROUND CONNECTION Figure 2-16.
Step 6. Installing LED/Switch Modules into Expansion Bays (4100U), Continued Mounting the Controller Card Assembly Refer to the figures and instructions below to mount the controller card assembly to the back of one of the LED/switch cards. 4. Use four 322-123 Nuts and four 268-009 Washers to secure the 637-141 Bracket to the inside front of the expansion box. Note that there are only two locations where the bracket can be mounted, as shown in Figure 2-16. 5.
Step 6. Installing LED/Switch Modules into Expansion Bays (4100U), Continued Changing Display Card LEDs, (continued) Figure 2-18. Assembling / Disassembling the LED Display Card Interconnecting Cards User interface wiring consists of connecting the LED/switch controller card to the expansion bay’s power distribution interface (PDI), and connecting display cards to each other. This section describes both procedures.
Step 6. Installing LED/Switch Modules into Expansion Bays (4100U), Continued Wiring Instructions The following directions are complete instructions on interconnecting display cards and connecting the controller card to a power source. 1. Use Harness 734-008 to connect P2 on the controller card to one of the 4-pin connectors on the PDI. 2. If there are multiple controller cards, use Harness 734-036 to connect P3 on the controller card to P2 on another controller card. 3.
The Terminal Block Utility Module (4100U) Overview The 4100-0632 Terminal Block Utility Module is an all-purpose terminal block that mounts to an expansion bay, above or below the power distribution interface (PDI). Each module utilizes one block of mounting space. The terminal block utility module has two 16-position terminal blocks that accept up to a maximum of 12 AWG (3.309 mm2) wire.
2-28
Chapter 3 Installing 4100 MINIPLEX Components (Non-4100U) Introduction 4100 host panel and remote locations. This chapter describes the transponder installation procedure for all MINIPLEX systems in non-4100U systems. In this Chapter Refer to the page number listed in this table for information on a specific topic.
Introduction to MINIPLEX Systems (Non-4100U) Overview The 4100 MINIPLEX Fire Alarm System uses transponder cabinets containing remote interface cards (RICs) to extend power and communication across large areas. MINIPLEX transponders allow the system to provide applications for up to 1000 monitor and/or control points and 2000 annunciator points (see note).
Introduction to MINIPLEX Systems (Non-4100U), Continued Overview (Continued) Seventh floor MINIPLEX transponder with solid door Legend: Sixth floor Speaker NAC TrueAlarm sensors and MAPNET II addressable circuits Fifth floor Audio riser wiring, twisted pair RUI communications wiring, twisted, shielded pair Fourth floor MINIPLEX transponder with LED/switch modules on door panel Third floor ACKNOWLEDGE Second floor FACP First floor Figure 3-1.
MINIPLEX System Components (Non-4100U) Overview The 4100 MINIPLEX system is comprised of a host panel containing everything required in a standalone cabinet (see Chapter 2), plus: • An RUI module in the master controller bay • One or more remote MINIPLEX transponder cabinets • A RIC II card in each transponder cabinet This section describes each component in turn.
MINIPLEX System Components (Non-4100U), Continued The Remote Interface Card (RIC) Remote interface cards (RICs) in the transponder cabinets allow for data, power, and audio interconnections between the 4100 host panel and remote locations. They support RUI connections in Style 4 and Style 7 wiring configurations.
MINIPLEX System Guidelines (Non-4100U) Overview The rules on this page apply exclusively to MINIPLEX systems. Review each guideline before installing a MINIPLEX 4100 system. Guidelines • The Style 4 RUI card supports MINIPLEX transponders and 4602/4603 serial annunciators on the same signaling line circuit.
Installing Modules into Cabinets (Non-4100U) Overview Guidelines Installing the RUI Motherboard This section contains guidelines and instructions for mounting the RUI and RIC II modules into 4100 cabinets. • The RUI motherboard mounts into the CPU bay or, if necessary, an expansion bay. • The RIC II mounts into expansion bays only. Review the following guidelines before installing a motherboard into a cabinet.
Installing Modules into Cabinets (Non-4100U), Continued Installing the RIC II Motherboard The RIC II motherboard is installed into a remote transponder cabinet. Review the following guidelines before mounting RIC II motherboard. • If a power supply is installed in the bay, it must be installed on the far right of the bay and any relay modules must be installed in the slots immediately to its left. • Relay cards must be installed in the rightmost possible slots.
Installing Modules into Cabinets (Non-4100U), Continued Connecting the 733-525 Harness If you need to connect a 733-525 Harness to a motherboard, refer to Figure 3-6 and follow these steps. Make sure to route the power and communication wiring on the left side of the bay. 1. Connect one end of the harness to a motherboard in an adjacent bay. If the adjacent bay is a master controller bay, connect the harness to the P2 and P3 connectors of the master controller motherboard and continue to step 2.
Installing Modules into Cabinets (Non-4100U), Continued TO 24 VDC RIC II RIC(565-233) II (565-233) Connector with Blue Wire Goes to P2 (OPTIONAL) UNIVERSAL POWER SUPPLY Connector with White Wire Goes to P3 733-525 Harness 733-672 Harness Figure 3-6.
MINIPLEX Wiring (Non-4100U) Overview The RIC must be connected to the host panel via RUI cabling. This section explains how to wire the two together, and how to set up a system with multiple transponders connected to the same host panel. Wiring Configurations RUI cabling can be accomplished either through Class A or Class B wiring. Class A wiring allows transponder cabinets to communicate with the FACP even in the event of an open circuit somewhere in the loop.
MINIPLEX Wiring (Non-4100U), Continued Wiring Illustration The illustration below applies to Class A and Class B wiring. 4100 MINIPLEX MASTER 562-856 W/565-217 RUI COMMS "A" +24 V 24 C COMMS "B" T B 1 T B 1 8 II RIC 11 565-233 CLASS B MINIPLEX TRANSPONDER CLASS A T B 1 1 See Note 1 8 MINIPLEX TRANSPONDER Figure 3-7. MINIPLEX Wiring Notes: 1. Power wiring is not shown. Connect the RIC II card to the UPS or expansion power supply in the transponder cabinet. 2.
Chapter 4 Installing 4100U MINIPLEX Components Introduction MINIPLEX transponder interface cards (TICs) allow for data and power interconnections between the 4100 host panel and remote locations. This chapter describes the transponder installation procedure for 4100U MINIPLEX systems. In this Chapter Refer to the page number listed in this table for information on a specific topic.
Introduction to MINIPLEX Transponders (4100U) Overview The 4100U MINIPLEX system is comprised of a host panel containing everything required in a standalone cabinet (see Chapter 1), plus: • One or more remote MINIPLEX transponder cabinets • A transponder interface card (TIC) in each transponder cabinet This section describes each component in turn.
Introduction to MINIPLEX Transponders (4100U), Continued The Local Mode TIC (Not currently available in Australia). The local mode TIC contains an RUI input, port for connecting to other transponder modules, and terminal block for connecting to an optional Local Mode Controller. Local Mode Controllers are mounted remotely from the transponder. Installation instructions are supplied with the controller.
Introduction to MINIPLEX Transponders (4100U), Continued TIC Illustrations Below is an illustration of the various TIC and audio riser circuit boards.
Introduction to MINIPLEX Transponders (4100U), Continued Local Mode Specifications Local mode is supported by the following: • 4100-3101/3104/3105 IDNet Card • 4100-5101/5102/5103 Expansion Power Supply NACs (including TrueAlert Non-Addressable SmartSync appliances) • 4100-5111/5112/5113 System Power Supply NACs (including TrueAlert NonAddressable SmartSync appliances) • 4100-5125/5126/5127 Remote Power Supply NACs (including TrueAlert NonAddressable SmartSync appliances) • 4100-5120/5121/5122 True
Introduction to MINIPLEX Transponders (4100U), Continued LEDs The TICs have the following LEDs: LED1. Illuminates to indicate communication loss with the CPU. LED2. Illuminates when an RUI ground fault search is active. LED3. Illuminates when Local Mode is active. LED4. Illuminates to indicate an RUI Style 7 primary trouble. LED5. Illuminates to indicate an RUI Style 7 secondary trouble. Refer to Figure 5-1 to see which LEDs are included on which TIC. Most TICs do not contain all LEDs.
MINIPLEX System Guidelines (4100U) Overview The rules on this page apply exclusively to MINIPLEX systems. Review each guideline before installing a MINIPLEX 4100U system. Guidelines • All wiring is 18 AWG (0.8231 mm2) (minimum) and 12 AWG (3.309 mm2) (maximum). • All wiring is supervised and power-limited. • All wiring that leaves the building requires overvoltage protection. Install module inside an UL-Listed electrical box wherever wire enters or exits the building.
Configuring Cards (4100U) Overview The TIC and all other cards to be mounted in the transponder cabinet and attached expansion bays must be configured to operate correctly in the system via their DIP switch and jumper ports. The CPU motherboard may have to be configured as well. CPU Motherboard DIP Switch P9 on the CPU motherboard determines whether the RUI SHIELD signal is connected to 24 C or Earth. • Position 1 – 2: SHIELD to 24 C (default). • Position 2 – 3: SHIELD to Earth.
TIC/Riser Mounting (4100U) Overview All TICs are mounted like any 4-inch (102 mm) X 5-inch (127 mm) card. This section describes the TIC/audio riser card mounting procedure, which is identical to that of other 4-inch (102 mm) X 5-inch (127 mm) cards. Mounting Instructions Use the following instructions and Figure 4-2, below, to mount 4”x 5” slave cards to an expansion cabinet. IMPORTANT: • The TIC must be mounted in the upper left position of the bay.
TIC/Motherboard Interconnections (4100U) Use Figure 4-3 to connect the TIC to a motherboard in another bay. RUI TMPR SW 24C INPUT PRI SHLD SEC P6 TB2 TB3 LED4 LED5 SPS OR RPS SW1 HARNESS 734-078 4100 COMM LOSS RUI G.F.
RUI Wiring (4100U) Overview The TIC must be connected to the host panel via RUI cabling. This section explains how to wire the two together, and how to set up a system with multiple transponders connected to the same host panel. Wiring Configurations RUI cabling can be accomplished either through Class A or Class B wiring. Class A wiring allows transponder cabinets to communicate with the FACP even in the event of an open circuit somewhere in the loop.
4-12
Chapter 5 Networking Introduction A standalone or MINIPLEX 4100 system becomes a network node when a 4100 Network Interface Card (NIC) or other compatible network card is installed and connected to another network node. How network cards connect to each other depends on the type of media network cards being used. In this Chapter Refer to the page number listed in this table for information on a specific topic.
Getting Started Overview This chapter describes how to turn a standalone or MINIPLEX FACP into a network node. This process consists of the following: Step 1. Configuring cards for operation (using DIP switches and jumper ports) Step 2. Mounting media cards to the network interface card (NIC) Step 3. Mounting network cards Step 4. Wiring network cards Each step is described in this chapter.
Introduction to the 4100 Network Interface Card (NIC) Overview The Network Interface Card (NIC) is a slave card that uses the standard 4100 serial bus to communicate with the master. The NIC connects FACPs in a network, allowing for communication between each panel via fiber, modem, or twisted shielded pair wire. The NIC is designed to be connected in a point-to-point arrangement, so that one wire fault does not cause the entire system to fail.
Introduction to the 4100 Network Interface Card (NIC), Continued Network Module Illustrations DATA TRANSMIT/ RECEIVE LEDs (LED2 THROUGH LED5) MEDIA CARD 40-PIN CONNECTORS (P5, P6) DATA RATE JUMPER PORT (P3) DATA PROTOCOL JUMPER PORT (P3) MOTHERBOARD CONNECTOR (P4) ADDRESS DIP SWITCH (SW2) YELLOW LED (LED1) DIAL-UP SERVICE MODEM CONNECTOR (P2) RESET SWITCH (SW1) Figure 5-1. 4100-6014 Network Interface Card NIC Card LED Indications The 4100-6014 NIC has the following LEDs: LED1 (yellow).
Introduction to the 4100 Network Interface Card (NIC), Continued NIC Motherboards The figures below are illustrations of two motherboards apart from the default CPU motherboard that can be used with the 4100 NIC. • The 565-274 Master Motherboard holds two daughter cards: the 4100 master controller card and the 4100 NIC. • The 565-275 Class B Motherboard holds the 4100 NIC by itself.
Introduction to the 4100 Network Interface Card (NIC), Continued NIC Media Cards There are two approved modules that can be plugged into the 4100-6014 NIC: • 4100-6057 Fiber-Optic Media Card (565-261) • 4100-6056 Wired Media Card (565-413) Each module is shown below. FIBER-OPTIC DATA: TRANSMIT (U1), RECEIVE (U2) 40-PIN NETWORK INTERFACE CARD CONNECTOR (J1) Figure 5-4. The 4100/4120-0143 Fiber-Optic Media Card 40-PIN NETWORK INTERFACE CARD CONNECTOR (P1) RESERVED (TB1) Figure 5-5.
Introduction to the 4100 Network Interface Card (NIC), Continued Requirements and Limitations Table 5-1. 4100 NIC & Media Cards - Electrical and Environmental Specifications Electrical Specifications Network Interface Card Startup, no media cards: 8 VDC @ 110 mA Nominal, no media cards: 20 to 32 VDC @ 0 mA Fiber Media Card Using 24 V power supply: 20 VDC @ 140 mA max. Using 5 V power supply (GCC/NPU): 5 VDC @ 130 mA max. Wired Media Card 4.75 to 5.25 VDC @ 170 mA max.
Step 1. Configuring Network Cards, Continued NIC Card Jumper Settings There are two shunt jumper ports on the NIC card that need to be set: P3 and P4. P3: Determines the NIC data transmission rate, 57.6 kbits/second or 9600 bits/second. • Position 1 – 2 (the right two pins) or no pins jumpered: 57.6 kbits/second. • Position 2 – 3 (the left two pins): 9600 bits/second. P4: Determines the data protocol, 8-bit or 9-bit, that the NIC card is using.
Step 2. Mounting Media Cards to the NIC Overview The 4100-6014 Network Interface Card (NIC) uses media cards to connect to other NICs. This section describes how the media cards are mounted onto NICs. Media Card Mounting NICs connect to each other via the three types of media cards. The types of media cards in the right and left ports are determined by the type of wiring that is being used across cards.
Step 3. Mounting Network Cards The 4100 NIC daughter card, shown in Figure 6-8 below, inserts into motherboards as follows: • If the 565-274 Master Motherboard is being used, the NIC daughter card is inserted into connector J1. • If the 566-227 Master Motherboard or 565-275 Motherboard is used, the NIC daughter card is inserted into connector J2. Figure 5-7.
Step 4. Wiring Network Cards Overview The nodes in the network now have to be wired together, so that the NIC in one host panel connects to the NIC in the next panel. This section contains guidelines and instructions for NIC wiring. Wiring Guidelines Refer to the following guidelines whenever field wiring the NICs. • Network nodes must be wired right to left port, regardless of the media type selected. • Style 7 protection is achieved by wiring the nodes in a loop fashion.
Step 4. Wiring Network Cards, Continued • 655-158 Transient Suppressor (ordered as part of 748-599) is required for each modem-to-telephone line connection. From Modem Transient Suppressor Assembly (655-158) added to RJ-31x as shown. If connecting to a terminal block, cut off one end of the cable. Strip back the cable to connect the two center wires, normally red and green, to the red and green wires in the block. 1 8 7 2 6 3 4 5 Grn Telephone Line Figure 5-8.
Step 4. Wiring Network Cards, Continued Fiber-Optic Wiring Connectors U1 (transmitter) and U2 (receiver) on the 4100-6057 Fiber-Optic Media Card are used to connect 4100-6014 NICs across parts of a network. Note: ST connectors with long strain relief boots are to be used with the fiber optic cable. Figure 6-10 shows how two network nodes are connected via fiber-optic cable. Fiber-Optic Cable U1 U2 U1 U2 U1 U2 U1 U2 FIBER MEDIA CARD 4100-6014 NETWORK INTERFACE CARD Figure 5-9.
Step 4. Wiring Network Cards, Continued 4190-9010 Coupler Requirements The 4190-9010 Coupler (271-012) is used with the 565-261 Fiber Optic Media Board, revision “C” or higher. Two 4190-9010 Bi-Directional Couplers are required per connection, one at each node. The 4190-9010 is equipped with type ST connectors. To make type ST to type ST connections, an ST to ST coupler, by others, is required.
Step 4. Wiring Network Cards, Continued 4190-9010 Coupler Requirements (continued) The illustration below shows coupler wiring. Figure 5-10. Coupler Wiring Wiring with the Wired Media Card Refer to the guidelines and figures in this topic to use wired media cards. IMPORTANT: TB1 on the wired media card must not be used when it is connected to the 4100-6014 NIC. • When the 565-413 Interface Card is used with 565-516, -407, or –409 Network Card, TB1 on the 565-413 Interface Card cannot be used.
Step 4. Wiring Network Cards, Continued Wiring with the Wired Media Card (continued) The Table below lists the 4100U master motherboard connections for the wired media card. Table 5-5.
Step 4. Wiring Network Cards, Continued Wiring Illustrations The figures below show how to wire the NIC. The illustrations use the 565-274 and 565275 motherboards only. If you are using the 4100U motherboard, refer to Figure 5-11 along with the figures below. Wired Media, Style 7 Wiring SEE NOTE 3 SEE NOTE 3 Notes: SEE NOTE 5 1. Refer to general wiring precautions in this chapter, as well as Field Wiring Specifications: document 900-082 for 4100; 900-242 for 4100U. 2.
Step 4. Wiring Network Cards, Continued Fiber Optic, Style 7 Wiring SEE NOTE 5 SEE NOTE 5 SEE NOTE 5 Notes: 1. Refer to general wiring precautions in this chapter, as well as Field Wiring Specifications: document 900-082 for 4100; 900-242 for 4100U. For specific information about fiber optic wiring, refer to the 900-143 Fiber Tutorial. 2.
Step 4. Wiring Network Cards , Continued Wired Media and Fiber Optic, Style 7 Wiring SEE NOTES 7 and 8 SEE NOTE 6 SEE NOTE 5 Notes: 1. Refer to general wiring precautions in this chapter, as well as Field Wiring Specifications: document 900-082 for 4100; 900-242 for 4100U. For specific information about fiber optic wiring, refer to the 900-143 Fiber Tutorial. 2.
5-20
Chapter 6 The System Power Supply & Alarm Relay Card Introduction The SPS is described in Chapter 2. A picture is shown in Figure 2.4. This chapter has the current and voltage ratings of the system power supply (SPS) and describes how it is installed and configured by the factory. It also describes the Alarm Relay Card that mounts onto the SPS to provide 3 extra relays. In this Chapter Refer to the page number listed in this table for information on a specific topic.
SPS Specifications Input/Output/Battery Specifications The following table summarizes the specifications for the SPS. Table 6-1. SPS Input and Output Specifications AC Input Specifications SPS in Standard Australian FACP 4100-9848AU 2 A Maximum 240 VAC + 6% -10% @ 50 Hz DC Output Specifications Nominal 28VDC Minimum: 19.5 VDC Maximum: 32 VDC Ripple: 2 VDC p-p @ full load (9A) Voltage 9A alarm load. Includes: NACs (+24V Sig); +24V Card; +24V Aux; SPS card power including on-board IDNet.
SPS Specifications, Continued SPS Current Consumption • +24V Sig is used to supply the NACs. It can be made accessible by configuring a NAC as an aux power output (normally energized). The PDI has a 24V Sig bus that is only powered when an SPS is plugged directly on to it. (Not in standard configuration). The 4100 MXP is the only Australian approved card that takes power from this bus. All other cards draw power from +24V Card. • The battery circuit is supervised every 29 seconds.
SPS Specifications, Continued Environmental Requirements The range of possible temperatures under which the SPS may function are between 0° C and 50° C (120° F). The SPS operates normally under non-condensing humidity conditions up to 93% with relative humidity at 32° C. SPS Configuration Overview This section contains information about SPS jumpers, DIP switches and potentiometers. Jumper Settings P2: If the SPS IDNet outputs are being used, you may change P2 to configure the IDNet shield connection.
SPS LED Indications LEDs The SPS has the following LEDs: LED1 (yellow). Illuminates when NAC 1 is ON or in Fault. LED2 (yellow). Illuminates when NAC 2 is ON or in Fault. LED3 (yellow). Illuminates when NAC 3 is ON or in Fault. LED4 (yellow). Illuminates to indicate a communications loss with the system CPU; normally off. If this LED is blinking, try re-loading the software to FLASH. LED5 (yellow). Indicates IDNet status. • Slow blink: Class A open circuit Fault. • Fast blink: Short circuit Fault.
Troubleshooting on SPS Overview This section contains explanations of fault messages that may appear on the 4100U display when using the SPS. Heading text in the left margin shows the error message, while the paragraph next to it describes the likely cause of the message. IDNet Power Monitor Trouble There is no output voltage from the power supply. Refer to Chapters 2 and 6 for information on power supplies. Extra Device Appears if one or more extra devices (i.e.
The Alarm Relay Card Overview The Alarm Relay Card mounts on, and is driven by, the SPS. It has 3 relays each providing one set of voltage-free contacts. The relays are able to be configured under custom control, but the default operation is for system status, i.e. Fault (Trouble), Isolate (Supervisory), and Alarm, respectively. These are commonly used to drive the Brigade signalling.
The Alarm Relay Card, Continued Configuration The relays have one set of voltage-free contacts (see note below) connected to one pair of terminals via a header. The two terminals are configured for normally closed or normally open by positioning a jumper on the header. Table 6-3.
Chapter 7 SPS Field Wiring (4100U) Introduction This chapter shows how various devices are wired to an SPS. It includes connection to NACs, IDNet, relays, and power circuits. In this Chapter Refer to the page number listed in this table for information on a specific topic.
General Field Wiring Guidelines General Guidelines Make sure these guidelines are accounted for before wiring: • All field wires must be 0.75 mm2 or greater and comply with AS1670.1 and the wiring code. • Conductors must test free of all grounds. • All wiring must be done using copper conductors only, unless noted otherwise. • If shielded wire is used, - the metallic continuity of the shield must be maintained throughout the entire cable length.
SPS NAC Field Wiring Guidelines Overview Each of the 3 NACs has two pairs of driven outputs (A+/A-, B+/B-) which operate together. NAC B outputs have polarity reversal supervision and expect a 10k EOLR. Each connected device must have a suitably rated blocking diode. NAC A outputs have an integral 10k to accommodate Class A (loop) wiring. Class A wiring is not mandatory under AS1670.1. The 3A max rating applies to each NAC, B + A outputs combined. NAC load current may be read on the LCD.
SPS NAC Field Wiring Guidelines, Continued Class A NAC Wiring To connect the SPS to reverse-polarity, non-addressable notification appliances using Class A wiring, read the following instructions and refer to the figure below. 1. Route wire (between 0.75 mm2 and 4 mm2) from the “B+”, “B-”, outputs on TB2 of the SPS to the appropriate inputs on a peripheral notification appliance. Use NAC1, NAC2, or NAC3 as configured.. 2. Route wire from the first appliance to the next one. Repeat for each appliance.
Class B NAC Wiring To connect the SPS to appliances using Class B wiring, read the following instructions and refer to the figure below. 1. Route wire (between 0.75 mm2 and 4 mm2) from the B+, B- outputs on TB2 of the SPS to the appropriate inputs on a peripheral notification appliance. Use NAC1, NAC2, or NAC3, as configured. 2. Route wire from the first appliance to the next one. “T” tapping is not allowed. Repeat for each appliance. 3.
Class A NAC Wiring Table Table 7-1 lists the maximum distances from the NAC terminal block to the last appliance in a Class A configuration, depending on wire gauge and current. Use Table 7-1 to calculate wire distances for your application if you are using Class A wiring. Table 7-1. Class A Wiring Distances Alarm Current @ 24 V Max Distance w/ 18 AWG (0.8231 mm2) Max Distance w/ 16 AWG (1.309 mm2) Max Distance w/ 14 AWG (2.081 mm2) Max Distance w/ 12 AWG (3.309 mm2) 0.25 A 420 ft. (128 m) 667 ft.
Power Supply Wiring Distances, Continued Class B NAC Wiring Table Table 7-2 lists the maximum distances from the NAC terminal block to the last appliance in a Class B configuration, depending on wire gauge and current. Use Table 7-2 to calculate wire distances for your application if you are using Class B wiring. Table 7-2. Class B Wiring Distances Alarm Current @ 24 V Max Distance w/ 18 AWG (0.8231 mm2) Max Distance w/ 16 AWG (1.309 mm2) Max Distance w/ 14 AWG (2.081 mm2) Max Distance w/ 12 AWG (3.
SPS Auxiliary Power Wiring Overview The panel, battery-backed, unregulated dc bulk power is available from the SPS via the NAC and the 24V Aux power terminals (1 pair only, ref fig 7-4). NACs not configured as switched outputs may be configured as auxiliary power point type in the 4100 Programmer. All of these are power-limited. Guidelines Review the following guidelines before using the SPS for auxiliary power. • Voltage rating: 24 VDC (nominal), 2 V P-P ripple (maximum).
SPS Auxiliary Power Wiring, Continued Wiring The SPS can connect to auxiliary power appliances via the dedicated auxiliary power tap (TB3). If more power is needed, any of the three NAC outputs can be used for EMC auxiliary power. AUXILIARY POWER 2 0.75 mm to 4 mm AUXILIARY POWER AUXILIARY POWER Ferrite bead required for EMC compliance. Use SX0005 or kit 4100-5129.
SPS Relay Wiring Overview The SPS has one programmable relay, Aux 1, with one set of voltage-free contacts (see below). It also has provision for mounting a 4100-6033 Alarm Relay that has 3 relays, each with one set of normally open (or normally closed) contacts available on a screw terminal block (see fig 6.1). Aux 1 Relay • The relay must be configured in the Programmer. • The relay circuit is rated to switch 2 A at 30 VAC or 32 VDC, resistive load.
SPS Auxiliary Relay Wiring, Continued Relays The Figure below shows the SPS relays. TB2 B+ B- A+ A- B+ B- A+ A- B+ B- A+ A- SPS ALARM RELAY MODULE Dedicated Auxiliary 1 relay terminal block P7 TB4 P4 NO C NC TERMINAL BLOCK Figure 7-5.
SPS IDNet Wiring Overview This section describes how the IDNet on the SPS connects to addressable devices/detectors. The guidelines governing IDNet wiring guidelines are covered in chpt 8, IDNet Installation. IDNet Wiring Up to 250 IDNet initiating devices are supported on the SPS IDNet channel. The SPS supports both Class A (loop) and Class B(string) wiring. Class A wiring is mandatory for connection to more than 40 devices.
SPS IDNet Wiring, Continued Class A Wiring To connect addressable devices/detectors to the SPS IDNet using Class A wiring, read the following instructions. 1. 2. Ferrite beads are required on the SPS IDNet cables (ref Fig 7.1). Route wire (between 0.75 mm2 and 4 mm2) from the B+, B- outputs on TB1 of the SPS to the appropriate inputs on a peripheral IDNet device. 3. Route wire from the first IDNet device to the next one. Repeat for each device. 4.
SPS IDNet Wiring, Continued Class B Wiring To connect addressable devices/detectors to the SPS IDNet using Class B wiring, read the following instructions. 1. 2. 3. Under AS1670.1 Class B wiring is allowed only for a maximum of 40 addressable devices. A ferrite bead is required on the SPS IDNet cable. On TB1, jumper B+ to A+, and jumper B- to A-. 4. Route wire (between 0.75 mm2 and 4 mm2) from the B+, B-. The illustration below shows Class B wiring.
Chapter 8 Installing 4100U IDNet & 4100MXP Cards Introduction Two loop cards are available in the 4100U 4”x 5”card format. These plug directly onto the PDI and form an intelligent interface between the 4100U CPU and one loop of addressable detectors/devices. The IDNet Card uses Mapnet Protocol and communicates with existing Mapnet detectors/devices plus the new IDNet devices. The 4100MXP communicates with the Tyco MX range of detectors/devices.
The IDNet Card Overview The 4100U IDNet card receives 24V power (+24V Card Supply bus) and coms (i.e. communication with the CPU) via the PDI. There are several versions, configured by links soldered on the pcb. The 4100-3101 used in Australia, communicates with up to 250 devices. An IDNet card may be fitted to a 4100 (non-U) bay in an upgrade panel by use of a bracket and interface pcb plus 4100 style power and coms wiring harness. The part number for the IDNet card, plus Interface bracket is KT0452.
The IDNet Card, Continued LEDs The IDNet card has the following LEDs: LED1. Normally off. Turns on steady if the IDNet card is not communicating with the 4100 CPU. LED2. Normally off. Illuminates to indicate a problem with the IDNet lines. • Steady on indicates channel failure. • One repetitive blink indicates a line short. • Two repetitive blinks indicate a Class A failure or an open line. Specifications Table 8-1.
Installing the IDNet Card onto the PDI Overview The 4100-series IDNet card is designed to be mounted on the PDI in a 4100U expansion cabinet. The card can be mounted on any of the PDI connectors. Use connector P2, labeled on the back side of the IDNet card, to connect to any of the eight PDI connectors as shown in the figure below. WASHERS STANDOFFS SCREW RETAINERS IDNet CARD #6 SCREWS PDI CONNECTOR (reverse side) PDI Figure 8-2.
Installing the ID-Net into a 4100 Card Bay Overview If a 4100 is upgraded to 4100U, IDNet cards can be fitted to existing 4100 bays by use of the Interface Card plus bracket. The bracket mounts to the bay as a 4100 card motherboard does and takes up 1 slot.
Configuring the Card Overview Configuring the card consists of selecting the shield tie point, and setting the device address.. Setting the Shield Tie Point If a shielded cable is used, connect the cable shield to the dedicated terminal on TB1 and use jumper port (P1) to select where the shield will be tied. Setting the Address • Position 1 - 2 connects the shield to 0 V. • Position 2 - 3 connects the shield to Earth.
Wiring to IDNet Devices Overview Up to 250 IDNet slave devices, such as smoke detectors and manual call points, can be connected to the IDNet card using Class A (loop) or Class B (line) wiring, with the following restrictions. Class A wiring allows the devices to communicate with the IDNet card even in the event of an open circuit somewhere in the loop. Class A wiring requires that two wires are routed from the IDNet card to each IDNet device, and then back again to the IDNet card. Under AS1670.
Wiring to IDNet Devices, Continued Table 8-2 Cable Run Lengths 0.75 mm2 385 m 769 m Wire Size Distance Distance Notes 1 mm2 513 m 1,026 m 1.5 mm2 769 m 1,538 m 2.5 mm2 1,282 m 2,565 m 4 mm2 2,052 m 4,104 m Resistance 20Ω 40Ω 1. The circuit allowance per device on the loop is 0.5mA with the LED off, 2mA with the LED on. A maximum of 20 LEDs get turned on at one time by IDNet Card (i.e. in alarm). 2. The minimum voltage allowed at the furthest device to guarantee operation is 24.9Vdc.
Wiring to IDNet Devices, Continued Class B Wiring To connect the IDNet card to appliances using Class B wiring, read the following instructions. 1. On TB1, jumper IDNetB+ to IDNet A+, and jumper IDNetB- to IDNetA-. If the jumper is absent, a Class A Trouble will be indicated on LED 2. 2. Route wire between 0.75 mm2 and 4 mm2 from the IDNetA+, IDNetA-, (or B+, B-) outputs on TB1 of the IDNet card to a junction box. Begin “T” tapping at the junction box. 3. Up to 40 devices maximum. 4.
Troubleshooting on IDNet Overview This section describes the messages that may appear on the 4100 display when using the IDNet card. Trouble messages appear on the left as titles, and possible causes are listed to the right in the text. IDNet Power Monitor Trouble There is no output voltage from the IDNet power supply. Replace the IDNet card. Extra Device Appears if one or more extra devices (i.e.
The 4100MXP Introduction Power Connection The 4100MXP is a 4” x 5” card, similar to the IDNet, but allows the 4100U to communicate with a Loop of MX devices. The firmware in the 4100U sees the 4100MXP as an IDNet, and all the MX devices are matched to the nearest Simplex device. The main difference of 4100MXP from IDNet is that it has a nominal 40V loop supply voltage and is capable of supplying up to 1A of loop current.
8-12
Chapter 9 PC Software Connections Introduction The service port on the door with the Operator Interface enables the 4100U to connect to PCs running important utilities, such as diagnostics, programming, CPU firmware downloading, and channel monitoring. In this Chapter Refer to the page number listed in this table for information on a specific topic.
Software Modes Overview The 4100U can connect to PCs running important utilities, such as diagnostics, programming, CPU firmware downloading, and channel monitoring. It connects to PCs running all of these utilities via the service port on the CPU daughter card. When a PC is located remotely from the FACP, the 4100-9832 Service Modem is used.
Software Modes, Continued Software Modes (continued) Master Bootloader Interface Mode. This mode downloads the Master CPU Exec firmware and the CFG.TXT file to the CPU via the serial port. serial download cable Laptop/PC running Laptop/PC running terminal emulation software programming file transfer 4100 Panel running Bootloader Figure 9-3.
9-4
Chapter 10 Australian Version Specifics Introduction This chapter provides detail on format and components that are specific to the Australian version 4100U that complies with AS4428. In this Chapter Refer to the page number listed in this table for information on a specific topic.
Summary Of Australian Version Specifics Overview The Australian fire alarm standards differ from those in the USA. Shipping costs from USA to Australia are significant, and the Australian market is small compared to the USA market. It is therefore necessary to: • • • AS4428 Requirements have an Australian specific panel format that differs from the standard USA panel format; have some Australian specific components; limit the number of system components available in the Australian version.
Australian Panel Format Overview The main difference with the Australian panels is that they are assembled in the Australian (Tyco) range of rack cabinets. Australian / USA Differences Some further specific differences follow: • Only the Expansion Bay is used, with the Controller CPU and Motherboard mounted in the right hand side of the first one. The standard US Controller Bay is not used. • The Operator Interface is fitted to an Australian specific 4U hinged bracket mounted above the first bay.
4100U Fan Control Module Overview ME0456 is a 4100U style Switch/LED display module specifically designed for fan control. It complies with the requirements of AS1668.1, 1998. It has rotary switches and LEDs for 4 fans. In order to accommodate the required rotary switches, the front plate is joggled forward so that it protrudes through the trim. Labeling The Fan Control switch positions of ON, AUTO and OFF, as per the standard, are permanently marked on the faceplate label.
Figure 10-1.
Brigade Interfaces Overview The Alarm Relay Card is typically used to provide a Brigade Interface. The default configuration is for the three relays to operate on Fault (Trouble), Isolate (Supervisory) and Alarm, respectively. The connection drawings for the Centaur ASE, Western Australia AIU and Queensland PPU are included in the appendix. Format These relays are normally de-energised and energise on the respective status.
Chapter 11 Installation Checklist, Commissioning & Maintenance Introduction When a branch designs a system and orders a 4100U panel, a “Configuration Sheet” is prepared. The factory builds the panel to the configuration sheet. This includes fitting, connecting and configuring cards and modules. The factory programs and tests the panel to the configured sheet. The CPU Card and any 4100 style (legacy) cards that are fitted to motherboards are then removed and packaged with the panel for shipping.
Installation Checklist Overview The following checklist should be completed by the installer. (Note that all pcbs are electronically tested and adjusted before being fitted to the FIP). 1. A) B) C) D) F) G) H) I) J) K) L) M) N) O) 2.
Alignment & Adjustment Overview All the 4100U cards and modules (pcbs) are tested and aligned in the factory before being supplied to the customer or fitted to a FIP. The only field adjustment that may be necessary is to set the battery charger voltage. (Note this has been set and should not need re-adjusting). R341 Battery Charger Voltage Should the battery charger voltage need adjusting, the method is as follows: 1.
Power Up & Placing into Operation To place the 4100U FACP into operation, perform the following steps: STEP 1 Ensure that the Mains Isolate Switch is OFF. STEP 2 Ensure that 240 VAC is connected to the panel from the mains distribution switchboard. STEP 3 and link Ensure that the Lithium battery is fitted to battery holder on the CPU card, P3 is fitted to the BAT ON position. Turn the Mains Isolate Switch ON. STEP 4 Check that the green "MAINS ON" LED indicator is on.
Maintenance The 4100U system must be kept free from faults and tested on a weekly, monthly and annual basis to verify that it is operating correctly. The tests required by part 8 of the standard AS1851 Maintenance of Fire Protection Equipment are detailed in the 4100U Operator’s Manual, LT0351. The Operator’s manual also provides detail of report printing and performing tests that are useful for checking the system.
11-6
Appendix A The Device Configuration DIP Switch Overview Addressable cards include a bank of eight DIP switches. From left to right (see Figure A1, below) these switches are designated as SWx-1 through SWx-8. The function of these switches is as follows: • SWx-1. This switch sets the baud rate for the internal 4100 communications line running between the card and the CPU. Set this switch to ON. • SWx-2 through SWx-8. These switches set the card’s address within the 4100 FACP.
Overview, (continued) Table A-1.
Appendix B Programming Requirements Introduction This appendix identifies the programming that is required to comply with AS4428. It does not provide equations or detail of programming. The separate 4100 Programming Unit Manual tells how to use the PC-based 4100U Programmer. In this Chapter Refer to the page number listed in this table for information on a specific topic.
Appendix C Checking System Wiring Overview This appendix contains instructions on how to use a volt/ohm meter to check system wiring. Using the Volt/ Ohm Meter When using the volt/ohm meter to check each circuit, make sure to adhere to the notes and instructions below. Notes: A. No Voltage B. Open Circuit • Ensure that no power is applied to the 4100U fire alarm panel and that all wiring is properly connected (terminal blocks, LED/switch module ribbon cables, etc.).
Appendix C: Checking System Wiring, Continued Meter Readings Table C-1 lists the correct meter readings for indicating appliances and initiating devices. Table C-1. Acceptable Zone and Signal Circuit Meter Readings Circuit Type Meter Reading Class B/Style B Initiating Device (Zone) Circuit From zone + to zone – (each zone) 3.
Appendix D Earth Fault Detection Overview This appendix contains instructions on how to use the Earth Fault Search feature of the 4100U diagnostics menus. Earth Fault Search is a diagnostic search of external field wiring that assists in locating circuits with earth faults. An earth fault occurs when an electrical circuit is shorted to ground. Although most circuits operate with a single earth fault, multiple earth faults can disable communications.
General Guidelines Review the guidelines below before initiating an Earth Fault Search. • The Detect Earth Fault jumper must be installed at each SPS, RPS, TPS, IPS, or 4009T for earth fault detection to occur. • Only one power supply per location is configured to detect earth faults. • For more reliable earth fault searching: - Use a Firefighter Telephone NAC for each telephone riser connection to a transponder.
Earth Fault Searching from the Front Panel Overview This section describes how to conduct an Earth Fault Search, from selecting the appropriate access code to correcting the fault. Access Level Selection The panel must be at the appropriate access level (1, 2, 3, or 4) in order to run diagnostics. To get to the correct access level, 1. Press the Menu button.
Earth Fault Searching from the Front Panel, Continued Starting the Earth Fault Search, Continued 8. Press the Enter button. The following options become available when you press the Next and Previous buttons: Press or to scroll Location Search Press or to scroll IDNet Channel Search Press or to scroll Last Search Result The search types are described below.
Earth Fault Searching from the Front Panel, Continued Search Option B: Select Channel If you select the IDNet Channel Search menu item, a list of IDNet channels to search becomes available. Use the Next and Previous buttons to scroll through the list. When the IDNet channel you want to search is shown and "Press to start search" displays, the search is ready to start. A sample screen is shown below.
Search Results Overview There are several types of results that can display at the end of an Earth Fault Search. This section covers all types of results. IMPORTANT: Once you have been directed to an earth ground fault and corrected it, it is recommended that you restart the system (warm- or coldstart). Non-Point Faults A non-point fault indicates a ground that cannot be traced to an addressable point (for example, a shield or an audio riser).
Search Results, Continued Point Faults, Continued 4009 IDNet NAC Extender/TrueAlert Addressable Controller faults. The message below shows a fault detected on the 4009 IDNet NAC Extender before the repeater connected to that circuit is turned on: CARD 2, IDNET CARD (250 POINTS) M1-18, 4009A NAC EARTH FAULT Conversely, the following example shows a fault detected after the repeater connected to that circuit is turned on: CARD 2, IDNET CARD (250 POINTS) M1-18, 4009A REPEATER EARTH FAULT IDNet isolator fault.
Earth Fault Search Example The illustration below shows a MINIPLEX system with one transponder that has three earth faults: • SPS NAC on the SPS in the Main Panel • RPS AUXPWR output on the RPS in Transponder 1 • IDNet channel in Transponder 1 SPS NAC 2 SPS Main Panel RPS AUXPW R RPS RUI Transponder 1 = Ground Fault IDNet Iso 1 Iso 2 IDNet Channel M2 Figure F-1. Earth Fault Example The panel reports two earth faults—one for each power supply. The third fault is as yet unreported.
Search Results, Continued B. Find and repair the indicated fault on Transponder 1. 1. Select Location Search. 14. Select the RPS located in Transponder 1 (this selects Transponder 1 as the location for the search). 15. When prompted, select exclusion of AUXPWR circuits. 16. Start the search. (The panel turns on the earth fault search trouble pseudo-point and the keypad inactivity utility pseudo-point to disable timeout during the search). 17. The search completes.
Appendix E Related Documentation The following manuals are relevant. Other Australian 4100 manuals may be found on the TSP website. Book Part Number Title LT0293 4100A FIP AS4428 Operators Manual LT0294 4100A FIP AS4428 Installation Manual LT0295 4100A FIP AS4428 Technical Manual LT0307 4100 Field Wiring Diagrams LT0313 4100 MXP Engineering/Technical Manual LT0314 4100 MXP Installation Instructions LT0351 4100U Operators Manual (For ordering, LT0351 is A5, LT0351A4 is A4.
Appendix E: Related Documentation, Continued Book Part Number (cont.) Title (cont.
Appendix E: Related Documentation, Continued Book Part Number (cont.) Title (cont.
Appendix F Compatible Actuating Devices Introduction This appendix describes the following: • • In this Chapter It lists devices that have been approved as compatible devices for use with the 4100A/4100U FIP. It lists the devices approved for use with the IDNet and shows the number allowed per loop. Refer to the page number listed in this table for information on a specific topic.
List of Approved Devices, Continued Hochiki Range - Conventional Detectors DCA-B-60R MK V DCC-A DCC-C DCD-A DCD-C DFE-60B DCA-B-90R MK 1 DFE-90D DFG-60BLKJ DFJ-60B DFJ-90D SPA-AB SIH-AM SIF-A MK 1 SIJ-ASN SLK-A SLG-A MK 1 SLG-AM MK 1 SLR-AS HF-24A MK 1 YBC-R/3A YBF-RL/4AH4 Type A heat detector Heat Type A Heat Type C Heat Type A Heat Type C Type B heat detector Type C heat detector Type D heat detector Type B heat detector Heat Type B Heat Type D Beam type smoke detector Ionisation smoke detector Smoke Smo
List of Approved Devices, Continued Brooks Range - Conventional Detectors PFS-A PFS-B PFS-C PFS-D PFS-P PFS-P MK II PFS-I PFS-I MK II Heat detector Type A Heat detector Type B Heat detector Type C Heat detector Type D Photoelectric smoke detector Photoelectric smoke detector Ionisation smoke detector Ionisation smoke detector Cerberus Range - Conventional Detectors D01191A DL01191A Beam Beam The following range of detectors may be used with MAPNET Modules.
List of Approved Devices, Continued Simplex MAPNET 2 Range – Addressable Field Devices 2190-9156 2190-9162 2190-9164 2190-9169 2190-9172 2190-9173 Module 4099-9032NL Mapnet 2 Monitor ZAM Mapnet 2 Signal ZAM Mapnet 2 Control ZAM Mapnet 2 Line Powered Short Circuit Isolator Mapnet 2 Supervised IAM Mapnet 2 Loop powered 2 Point Input / Output Mapnet 2 Addressable Manual Call Point Compatible Detectors, IDNET The following lists the detectors approved for use with IDNet and shows current rating and numbers a
Compatible Addressable Field Devices, IDNet The following lists the addressable devices approved for use with IDNet and shows current rating and numbers allowed per loop. Device Type Operating Current mA 4090-9116 IDNet Comms Isolator 4090-9118 Relay IAM with T-sense 4090-9117 Addressable Power Isolator 4090-9118 Relay IAM with T-Sense Input 4090-9119 Relay IAM with unsupervised Input 409-9120 6 Point I/O 4090-9001 Supervised IAM 0.5 (2 with LED on) 0.5 (2 with LED on) 0.
Appendix G Compatible Batteries The following batteries are compatible with the 4100U.
Appendix H 4100U Specifications General System Capacity 2,000 points of addressable points, plus 2,000 points of annunciation. Expansion Up to capacity above. Up to 119 Addressable cards Cabinet Size Dependent on system configuration Cabinet Material 1.
Voltage & Current Ratings of Modules & Assemblies The DC input voltage range of the following modules is 18-33Vdc. The current listed is nominal for 24Vdc, and may be used for battery capacity calculations.
Appendix I Power Supply & Battery Capacity Calculations Power Supply Part of the system design includes calculating that the quiescent load and the alarm load are each less than the rating of the power supply. Note that the quiescent load includes devices such as door holders that are normally energized, but get switched off during alarm. The SPS rating is included in the specifications in Chapter 6. Refer to AS1670.1 Section 8.2.3 for a definition of the loads to be calculated.
Appendix J Cable Characteristics IDNet The IDNet cabling requirements are detailed in Chapter 8 of this manual. 4100 MAPNET II Line Characteristics Note: In the following paragraphs the term "MAPNET channel" is used to mean those lines connected to any one Mapnet Transceiver board. Parallel runs from the same board do not constitute separate channels. The term "continuous run" refers to the loop distance from the primary output, through all devices and back to the secondary output.
Network, Continued Fibre Optic Cable Characteristics All fibre cables shall be multimode, graded index. ST style connectors must be used. No physical strain shall be put on the cables. There must be no cable bends of less than a 50mm radius. Two methods are available for joining fibre cable. Splices provide a permanent, very low loss, fibre-to-fibre connection. Couplers provide temporary connection between two ST style connectors with a loss of 1.2dB. Both methods are permitted on a fibre Network.
Appendix K List of Drawings The following drawings are included and are referred to in the manual or are considered relevant.
©2004 Tyco Safety Products Westminster, Westminster, MA 01441-001 USA. Specifications and other information shown were current as of publication, and are subject to change without notice.
