TYCON TP-SSW5(-NC) 5 port PoE Endspan (Switch) USER’S MANUAL TYCON POWER SYSTEM
User’s Manual TYCON TP-SSW5(-NC) 1. General Information.............................................................. 3 2. Hardware Description........................................................... 3 LED Indicators....................................................................................... Power Wiring ........................................................................................ Ethernet Port Wiring.............................................................................
User’s Manual TYCON TP-SSW5(-NC) 1. General Information The PoE (Power Over Ethernet) Switch support four ports 10/100 TX ports with PoE injector plus one 10/100TX up-link port. The switch provide Power over Ethernet functions to deliver 35Watts power budget to powered device(PD), which is in compliance with IEEE802.3af/at standard to deliver both of Ethernet data and DC power through the traditional UTP or STP cable to the PD. This manual will help you install and maintain the PoE switch.
User’s Manual TYCON TP-SSW5(-NC) *PWR Indicator LED Power STATUS Description Green LED ON if power input has valid power apply. Red LED ON if the following condition happens. *Power input under voltage (Vin<10V) *Power input over voltage (Vin>59V) *PoE over current (2A/per port) the indicator is used on current model only.
User’s Manual TYCON TP-SSW5(-NC) *PoE LED(the left indicator on RJ45) LED STATUS P1~P4 Yellow Description LED ON if with PoE output. PoE Off No PoE output. *Power wiring The PoE switch family includes 2 models, be used for different ranges of input voltage as, Current model (2A maximum) ……….full range voltage (10 to 57VDC) (TP-SSW5-NC) 802.3af/at model…………………………48VDC typical (44 to 57VDC) (TP-SSW5) For 802.3af/at model operation, make sure your power supply may offer at least 75W for 4x 802.
User’s Manual TYCON TP-SSW5(-NC) Rear panel terminal block wiring detail: You could use the TP-SSW5(-NC) with our adaptor products as the below: (OPTION) Maximum output PSHP-18 PSHP-24 PSHP-48 18VDC/7.5A 24VDC/6.25A 48VDC/3.125A 135W 134.5W 134.5W Max. Output Power of the TP-SSW5-(NC) *Ethernet Port Wiring The PoE Switch supports Port 1 to Port 5 with automatic MDI/MDI-X crossover, autosense of the speed and duplex for 10Base-T or 100Base-TX connections.
User’s Manual TYCON TP-SSW5(-NC) Straight-through Cabling Pin 1 Pin 1 Pin2 Pin 2 Pin3 Pin 3 Pin6 Pin6 Cross-over Cabling Pin 1 Pin 3 Pin 2 Pin 6 Pin 3 Pin 1 Pin 6 Pin 2 Connect an Ethernet cable into any switch port and connect the other side to your attached device. The green Link/Act LED will light up when the cable is correctly connected. Refer to the LED Indicator section for descriptions of each LED indicator.
User’s Manual TYCON TP-SSW5(-NC) *PD Port Wiring Port 1 to 4 provide PoE inject function with maximum 35W(or 2A max.) ability to power up the powered device use the straight-through or cross-over Ethernet cable. The PoE switch follows the IEEE802.3af Alternative B mode connector assignment. The following table shows pin assignment of alternative A and B for the Power Source Equipment.
User’s Manual TYCON TP-SSW5(-NC) Flow control IEEE802.3x(full-duplex),back pressure(half-duplex) Data transmission rate 148800pps for 100base-T, 14880pps for 10base-T Address table 1K MAC address table, self-learning Connect RJ-45 PoE port Port 1-4, auto power management Pin assignment: TX(1,2), RX(3,6), V+(4,5), V-(7,8) Maximum PoE power IEEE802.3af – 16.8W IEEE802.3at – 35W Current limited – 2A PoE disconnect mode DC disconnect PoE auto detection IEEE802.3af & IEEE802.
User’s Manual TYCON TP-SSW5(-NC) Operating temperature -40℃~ 85℃ Operation humidity 90% relative humidity, non-condensing Storage temperature -55℃~+105℃ Dimension 40mm(H)x116mm(W)x90mm(D) (main body) 10 TYCON POWER SYSTEMS
