Integration Manual
Table Of Contents
- Document Information
- Contents
- 1 System description
- 1.1 Overview
- 1.2 Architecture
- 1.3 Pin-out
- 1.4 Operating modes
- 1.5 Power management
- 1.6 System functions
- 1.7 RF connection
- 1.8 (U)SIM interface
- 1.9 Serial communication
- 1.9.1 Serial interfaces configuration
- 1.9.2 Asynchronous serial interface (UART)
- 1.9.2.1 UART features
- 1.9.2.2 UART signal behavior
- 1.9.2.3 UART and power-saving
- 1.9.2.4 UART application circuits
- Providing the full RS-232 functionality (using the complete V.24 link)
- Providing the TxD, RxD, RTS, CTS and DTR lines only (not using the complete V.24 link)
- Providing the TxD, RxD, RTS and CTS lines only (not using the complete V.24 link)
- Providing the TxD and RxD lines only (not using the complete V24 link)
- Additional considerations
- 1.9.3 USB interface
- 1.9.4 SPI interface
- 1.9.5 MUX protocol (3GPP TS 27.010)
- 1.10 DDC (I2C) interface
- 1.11 Audio Interface
- 1.12 General Purpose Input/Output (GPIO)
- 1.13 Reserved pins (RSVD)
- 1.14 Schematic for LISA-U2 module integration
- 1.15 Approvals
- 1.15.1 European Conformance CE mark
- 1.15.2 US Federal Communications Commission notice
- 1.15.3 Innovation, Science, Economic Development Canada notice
- 1.15.4 Australian Regulatory Compliance Mark
- 1.15.5 ICASA Certification
- 1.15.6 KCC Certification
- 1.15.7 ANATEL Certification
- 1.15.8 CCC Certification
- 1.15.9 Giteki Certification
- 2 Design-In
- 3 Features description
- 3.1 Network indication
- 3.2 Antenna detection
- 3.3 Jamming Detection
- 3.4 TCP/IP and UDP/IP
- 3.5 FTP
- 3.6 HTTP
- 3.7 SSL/TLS
- 3.8 Dual stack IPv4/IPv6
- 3.9 AssistNow clients and GNSS integration
- 3.10 Hybrid positioning and CellLocate®
- 3.11 Control Plane Aiding / Location Services (LCS)
- 3.12 Firmware update Over AT (FOAT)
- 3.13 Firmware update Over the Air (FOTA)
- 3.14 In-Band modem (eCall / ERA-GLONASS)
- 3.15 SIM Access Profile (SAP)
- 3.16 Smart Temperature Management
- 3.17 Bearer Independent Protocol
- 3.18 Multi-Level Precedence and Pre-emption Service
- 3.19 Network Friendly Mode
- 3.20 Power saving
- 4 Handling and soldering
- 5 Product Testing
- Appendix
- A Migration from LISA-U1 to LISA-U2 series
- A.1 Checklist for migration
- A.2 Software migration
- A.2.1 Software migration from LISA-U1 series to LISA-U2 series modules
- A.3 Hardware migration
- A.3.1 Hardware migration from LISA-U1 series to LISA-U2 series modules
- A.3.2 Pin-out comparison LISA-U1 series vs. LISA-U2 series
- A.3.3 Layout comparison LISA-U1 series vs. LISA-U2 series
- B Glossary
- Related documents
- Revision history
- Contact
LISA-U2 series - System Integration Manual
UBX-13001118 - R25 Appendix Page 173 of 182
LISA-U1 series
LISA-U2 series
40
MIC_P
LISA-U120,
LISA-U130:
Differential analog
audio input (pos.)
LISA-U100,
LISA-U110:
RESERVED pin
I2S1_TXD /
GPIO7
LISA-U2 series:
2
nd
I
2
S Tx data output /
GPIO
LISA-U120, LISA-U130:
Differential analog audio input (pos.)
LISA-U2 series:
I2S1_TXD and configurable GPIO, 1.8 V
typ.
Output driver strength = 1 mA
Functions:
I2S1_TXD (default)
Pad disabled
Input / Output
41
I2S_WA
LISA-U120,
LISA-U130:
I
2
S word alignment
LISA-U100,
LISA-U110:
RESERVED pin
I2S_WA
LISA-U2 series:
1
st
I
2
S word alignment
input/output
I2S_WA, 1.8 V typ.
LISA-U120, LISA-U130:
Output driver strength = 2.5 mA
Internal active pull-down = 100 µ A
LISA-U2 series:
Output driver strength = 2 mA
Internal active pull-down = 200 µ A
42
I2S_TXD
LISA-U120,
LISA-U130:
I
2
S Tx data output
LISA-U100,
LISA-U110:
RESERVED pin
I2S_TXD
LISA-U2 series:
1
st
I
2
S Tx data output
I2S_TXD, 1.8 V typ.
LISA-U120, LISA-U130:
Output driver strength = 2.5 mA
LISA-U2 series:
Output driver strength = 2 mA
43
I2S_CLK
LISA-U120,
LISA-U130:
I
2
S clock
LISA-U100,
LISA-U110:
RESERVED pin
I2S_CLK
LISA-U2 series:
1
st
I
2
S clock
input/output
I2S_CLK, 1.8 V typ.
LISA-U120, LISA-U130:
Output driver strength = 2.5 mA
Internal active pull-down = 100 µ A
LISA-U2 series:
Output driver strength = 2 mA
Internal active pull-down = 200 µ A
44
I2S_RXD
LISA-U120,
LISA-U130:
I
2
S Rx data input
LISA-U100,
LISA-U110:
RESERVED pin
I2S_RXD
LISA-U2 series:
1
st
I
2
S Rx data input
I2S_RXD, 1.8 V typ.
LISA-U120, LISA-U130:
Output driver strength = 2.5 mA
Internal active pull-down = 100 µ A
LISA-U2 series:
Output driver strength = 2 mA
Internal active pull-down = 200 µ A
45
SCL
I
2
C bus clock line
output
SCL
I
2
C bus clock line
output
LISA-U1 series:
I
2
C SCL for GNSS, 1.8 V typ.
Fixed open drain
External pull-up (e.g. to V_INT) required
LISA-U2 series:
I
2
C SCL for GNSS and other I
2
C devices,
1.8 V typ.
Fixed open drain
External pull-up (e.g. to V_INT) required
46
SDA
I
2
C bus data line
input/output
SDA
I
2
C bus data line
input/output
LISA-U1 series:
I
2
C SDA for GNSS, 1.8 V typ.
Fixed open drain
External pull-up (e.g. to V_INT) required
LISA-U2 series:
I
2
C SDA for GNSS and other I
2
C devices,
1.8 V typ
Fixed open drain
External pull-up (e.g. to V_INT) required