User's Manual

TWS Pairing
接听/挂断电话
In off mode, touch and hold the headset panel for about 10
seconds (off state）→ ON MODE（2 seconds）→ Delete
pairing records(10 seconds), until hearing the “Du” voice for 3
times, and the red/blue light flashes twice at the same time.
Delete Pairing Records on the Headset
In music playing mode, long touch the panel of headset(R) for 2
seconds till hear speaker prompt “Du+Du di” to next song; Long
touch the headset(L) panel about 2 seconds till hear twice
“Du+Du”, it will play last song.
Forward/Backward
Two-call Handling
Note:
All the above operations have to respect the precondition
supported Bluetooth hands free profile V1.5 and Phones are running
holding function (Network services) from telecom.
When you are answering a call, there is another call coming :
(Only support the mobile phone which has the function of handling two
phones.)
1.Long touch the panel of headset(R) or headset(L) for 2 seconds to end the
current call and answer incoming call,
the speakers will prompt “call ended”
2.Double touch the panel of headset(R) or headset(L) to hold the current call
and answer incoming call;
3.After the second implementation, double touch the panel of headset(R) or
headset(L) to switch between two calls;
4.After the second implementation, long touch the panel of headset(R) or
headset(L) for 2 seconds to end the current call without prompt voice. Long
touch the panel of headset(R) or headset(L) to end another call and prompt
“call ended”;
5.The second incoming call prompts “DuDu”, there is no prompt for
answering the second call and switching two calls.
power on and waiting for 10
seconds , the two headsets will
enter auto-pairing mode. The
two headsets connect
with each other after few seconds, the headset (R) alternately
flashing red and blue, and then open the phone's bluetooth device
to search.
Bluetooth
ON
BS213GB-R
Pick up the two headsets
from the charging base to
On OFF state, touch the panel of headset (R) or headset (L) for 2
seconds to power on and waiting for about 10 seconds , the two
headsets will enter auto-pairing mode. The two headsets connect
with each other after few seconds, the headset (R) alternately
flashing red and blue, and then open the phone's bluetooth device
to search “BS213GB-R”.
Answering / Ending a Call
When incoming call, double touch the panel of headset (R) or
headset (L), the speaker prompts once “Du” to answer call; In call
mode, double touch the panel of headset (R) or headset (L) until
heard “Call ended” to end a call.
Rejecting a call
When incoming call, long touch the panel of
the earphone (R) or (L) for 2 seconds, then the
main earphone (R) or (L) speaker will prompt
"Call Rejected".
Voice dial function
On standby mode or music playing state, double
touch the earphone (L), the speakers will prompt
once “Voice dial” to activate this function
Note:This feature only supports mobile phones
with voice dial-up functions.
Adjusting the Volume
In call mode or music mode, touch the panel of the headset(R) to
volume up and touch the headset(L) to volume down. Once “Du”
can be heard when volume is up to maximum or minimum.
Maintenance
Do not use abrasive cleaning solvents to clean the headset.
not allow the headset to touch with any sharp objects as this will
scratching and damage
Please keep headset away from high-temperature, humidity and dust.
Do
TWS Reconnected
Method1:
Method2:
Touch the panel of headset (R) and (L) at the same time for 2
seconds to power on → wait for several seconds and the two
headsets will automatically connect → wait a few seconds for the
headset to connect with the paired phone → re-connection
successfully.
When you pick up the headset from the charging case after 3
seconds to power on→wait for a few seconds, the two headsets will
automatically connect→wait for a few seconds, the headset will be
linked with the paired mobile phone→ re-connection successfully.
Faults Reasons Solutions
Can not turn on low battery protection Charging headsets for 2-3 hours
Turning off
automatically
Low battery Charging headset for 2-3 hours
The charging base without
power, the headset will auto turn
Charging for charging base
Press the headphone charging
power switch
Headset echo Volume is too loud or
environment is noisy
Adjust the volume at phone or
change a place
Noise in call
Change a place or move to
close the headset and mobile
Wrong pairing Pairing again
Too many pairing records
Delete pairing records according
to user manual
Charging base without
indicator light when
charging
DC power supply doesn’t
output power
Check whether the micro USB
charging line is plugged or the
power switch is on
Headsets without
indicator light when
charging
Can not turn on by picking
up the headset /No indicator
light when headset being
charged
Charging base low battery
protection
Charging both the headsets and
charging base for 2-3 hours
The two headsets TWS
pairing failure/TWS paired
successful but can not find
the headset(R)
No sounds after
pairing
Common Faults and Exclusion
Low voice of the calling
party
Wearing headset is wrong
Adjusting wearing position of
headset
Wearing headset is wrong
Adjusting wearing position of
headset
The headsets couldn’t being
charged in charging base
1)Checking headset charging interface
whether has touched to POGO PIN of
charging base and the location is
correct or not.
2)Charging for charging base
3) whether the button is pressed state
Environmental interference
caused or distance between
headset and mobile is too far
on and paired
The headset charging power
switch bounce
The headset no
charging after put
back to the charging
base
NOTE 1: This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to part 15 of
the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation.
This equipment generates uses and can radiate radio frequency
energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communica-
tions. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the
following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help
Changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to
operate the equipment. This device complies with Part 15 of the
FCC Rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including
interference that may cause undesired operation.
Operate as the above ways: 1 or 2 ,and it prompts ”Connected”
after TWS paired successfully: left headset prompts "Left
connected" and right headset prompts "Right connected-pairing"
Music Pause/Playing
On standby mode, double touch the panel of
headset(R) to play music.
On music playing state, double touch the panel
of headset(R) to PAUSE music.
TWS wake up
NOTE 2: This equipment has been tested and found to
comply with the limits for a Class B digital device, pursuant to
part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful
interference in a
residential installation. This equipment generates uses and
can radiate radio
frequency energy and, if not installed and used in accordance
with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that
interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or
television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and
receiver.
-Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for
help
Changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to
operate the equipment.
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and (2)
this device must accept any interference received, including
interference that may cause undesired operation.
Note: When the first time to pairing or after delete the pairing
records, the headsets should be paired under 20cm unobstructed.
Cell phone begins to search for bluetooth
devices (see the user guide of your phone
instructions), and select “BS213GB-R”
from bluetooth device list.
After connected with phone, the headset R
will prompt “connected” .
Note: When the headsets TWS pairing
failures, short touch the headset R and
headset L to enter TWS pairing, then pair
with phone.
Note:
The headset R and headset L speaker will prompt "Connected" at the sa
time, (L) prompts "Left Connected", (R) prompts "Right Connected" .
If there's no any operations on headsets for more than one minute, it
requires to touch the headset to wake it up, then continue for other headset
operations
Note:
1. When the headset R is used alone, only can realize pause and play
the music, can’t realize other functions;
2. The headset L can’t be used alone.