™ Installation Guide 2075R Refrigerator and 2075RF Refrigerator/Freezer www.U-LineService.com Phone (414) 354-0300 • FAX (414) 354-7905 Service & Parts Tech Lines Phone (800) 779-2547 • FAX (414) 354-5696 OnlineService@U-Line.
™ 2075R Refrigerator and 2075RF Refrigerator/Freezer Contents Exterior Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Cut-Out Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . Product Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . Door Swing/Clearances Information . . . . . . . . . . . . . . Reversing the Door. . . . . . . . . . . . . . . . . . . . . . . . . . . . . Other Site Requirements . . . . . . . . . . . . . . . . . . . . . . . .
™ 2075R Refrigerator and 2075RF Refrigerator/Freezer General Precautions 2 Inspect and Plan Use this appliance for its intended purpose only and follow these general precautions along with those listed throughout this guide: You have received a carton containing your 2075R Refrigerator or 2075RF Refrigerator/Freezer with a package inside containing a User Manual and a Product Registration Card. Complete and mail the Product Registration Card or register online at www.U-LineService.com.
™ 2075R Refrigerator and 2075RF Refrigerator/Freezer After all the protective coating has been removed from the unit/door, clean all Stainless Steel surfaces with Claire Stainless Steel Polish and Cleaner or comparable product or a mild detergent and warm water solution and soft cloth. Do NOT use abrasive cleaning agents. 3 Prepare Site Your U-Line product has been designed for either freestanding or built-in installation.
™ 2075R Refrigerator and 2075RF Refrigerator/Freezer Product Dimensions Reversing the Door (Black and White Units Only) 25-3/8" Including Handle 23-1/4" Including Handle 34-1/8" 34-1/8" 23-15/16" Black and White All U-Line units (except Stainless Steel models) may be left- or right-hand opening. The door opening is easily reversed by moving the hinge hardware to the opposite side.
™ 2075R Refrigerator and 2075RF Refrigerator/Freezer 4. Remove the two door closer inserts from the existing bottom hinge and install as shown on the new bottom hinge (see Figure 8). 8. Holding door upright with top of door tilted forward, place hole of door pivot plate on bottom hinge screw pin (see Figure 10). 9. Tilt top of door into position in top hinge and install top hinge screw pin. Hinge Screw Pin 10. Install plastic screw plugs removed in Step 2 in old hinge holes (3 each, top and bottom).
™ 2075R Refrigerator and 2075RF Refrigerator/Freezer Side-By-Side Installation Instructions 4 Prepare and Install Door Panel (Black and White Units Only) For a complete refreshment center, install your 2075R or 2075RF Model beside a U-Line Ice Maker, Combo or Wine Captain Model (see Figure 11 for typical cut-out). Note that each Side-By-Side Installation will be different.
™ 2075R Refrigerator and 2075RF Refrigerator/Freezer Full Overlay Door Panel Door Panel Preparation A full overlay door panel completely covers the doorframe and handle to give a built-in appearance. See your U-Line dealer for the optional Full Overlay Door Panel Kit (P/N U-OL2075B — Black or P/N U-OL2075W — White). Appropriate hardware, Modified Handle, Replacement Hinges and a copy of these instructions will be included in the kit. Figure 12 1.
™ 13/32" 2075R Refrigerator and 2075RF Refrigerator/Freezer 0.177" Dia. (#16 Drill) x 11/16" Deep 4. Drill hole for upper door hinge (top of panel) (see Figure 16, Top View). 13/32" 0.177" diameter (#16 drill) x 11/16" deep 3/8" 3/8" 5. Drill hole for lower door hinge (see Figure 16, Bottom View). Door Bottom: 5/16" Dia.
™ 2075R Refrigerator and 2075RF Refrigerator/Freezer 5. Remove the top handle and discard. (This handle will be replaced with the Modified Handle included in the Full Overlay Door Panel Kit.) Tape Back of Wood Panel Removed Door Panel 6. Remove the two screws located on both sides of the lower handle. Remove the handle. 7. Attach the Modified Handle to the lower handle using the three screws removed in Step 4. Set aside. 8. Slide the existing door panel out of the doorframe.
™ 2075R Refrigerator and 2075RF Refrigerator/Freezer Typical Wood Panel Door Panel Pivot Post Wood Panel Top Hinge Plate (5/8" Longer than Existing Top Hinge Plate) Top Pivot Plate #10 x 5/8" Round Head Screw Seven Required #8-32 x 1/2" Flat Head Screw Three Places Plastic Spacer Seven Required Top Pivot Plate Figure 22 Door Panel 5. Remove the existing bottom pivot plate and replace with the Full Overlay pivot plate (see Figure 23). Figure 24 3.
™ 2075R Refrigerator and 2075RF Refrigerator/Freezer 5 Adjust Door Checking Door Alignment The unit’s door is aligned at the factory before shipment. However, its alignment could have been disturbed during shipment or during door panel installation. Slotted Mounting Holes Notch IMPORTANT Properly aligned, the door should be 1/8" below the top of the unit’s cabinet, NOT flush with the top (see Figure 26). Raise Outside Door Edge Lower Outside Door Edge Figure 28 1/8" 3. See Figure 28.
™ 2075R Refrigerator and 2075RF Refrigerator/Freezer 6 Prepare Power Supply 7 Level the Unit Electrical Specifications Leveling Information Note: It is recommended that the unit is level. CAUTION 1. Use a level to check the levelness of the unit from front to back and from side to side. Level should be placed along top edge and side edge as shown (see Figure 31). Electrical installation must observe all state and local codes.
2075R Refrigerator and 2075RF Refrigerator/Freezer ™ Door Shelves 8 Install the Unit 1. First pull shelf up at a 45° angle, then straight out (see Figure 34). Installation of the 2075R/2075RF 1. Plug in the power cord. Notch 2. Choose new location and line up on bosses. First push straight in, then down at a 45° angle. 2. Gently push the unit into position. Be careful not to entangle the electrical cord. 3. Re-check the leveling, from front to back and side to side. Make any necessary adjustments.
™ 2075R Refrigerator and 2075RF Refrigerator/Freezer Start-Up Troubleshooting 9 Start-Up for the First Time Q: Problem Initial Start-Up Unit does not appear to turn on when switch is set to ON. The unit is shipped with the control preset. No adjustments should be necessary at this time. For information about Adjusting the Temperature Control, see the User Manual. A: Solution Make sure unit is plugged in and outlet has power (circuit breaker has not tripped).
™ Who to Call Service Information If the need for service arises, contact the dealer from whom the unit was purchased. State the Model Number and Serial Number and explain the problem. The Model and Serial Number plate is located inside unit at upper right hand corner. If you need to locate a service company, you can go online at www.U-LineService.com and search for a service company by zip code.