QUICK START GUIDE Modular 3000 Series • 3018 CLR • 115 V / 60 Hz
QUICK START GUIDE u-line.com WELCOME TO U-LINE Congratulations on your U-Line purchase. Your product comes from a company with over five decades of premium modular ice making, refrigeration, and wine preservation experience. U-Line continues to be the American leader, delivering versatility and flexibility for multiple applications including residential, light commercial, outdoor and marine use.
QUICK START GUIDE u-line.com This Quick Start Guide covers the basics of installation and general use of your product. For more details, see the complete User Guide & Service Manual on u-line.com.
QUICK START GUIDE u-line.com Safety and Warning Environmental Requirements NOTICE This model is intended for indoor/interior applications only and is not to be used in installations that are open/ Please read all instructions before installing, exposed to natural elements. operating, or servicing the appliance. This unit is designed to operate between 50°F (10°C) and Use this appliance for its intended purpose only and follow 100°F (38°C).
QUICK START GUIDE u-line.com Electrical Water Hookup PREPARE PLUMBING ! WARNING The water valve uses a standard 1/4" (6.35 mm) compression fitting. U-Line recommends using accessory SHOCK HAZARD — Electrical Grounding water hook up kit – part # WATERHOOKUP. The kit Required. Never attempt to repair or perform includes a 10' (3 m) braided flexible water supply line and maintenance on the unit until the electricity has a brass hose fitting. been disconnected.
QUICK START GUIDE u-line.com 3. Locate water ! CAUTION valve in the front of the unit and Do not use any plastic water supply line. The line thread water is under pressure at all times. Plastic may crack supply line or rupture with age and cause damage to your through. home. Route the water Do not use tape or joint compound when supply line attaching a braided flexible water supply line through the unit that includes a rubber gasket.
QUICK START GUIDE u-line.com Drain GRAVITY DRAIN Model numbers including “-00” or “-07” do not include a factory installed drain pump. Normal Proper Drain Model numbers including “-40” or “-47” include a factory installed drain pump. With Trap Poor Drainage, Water Will Back Up DRAIN CONNECTION ! CAUTION With Trap and Vent Proper Drain If your U-Line unit did not come with a factory installed drain pump you must use a gravity A gravity drain may be used if: style drain connection.
QUICK START GUIDE u-line.com FACTORY INSTALLED DRAIN PUMP Y-Branch Tailpiece P60 Pump Required If your drain line will run up to a stand pipe, disposal or Air Gap (Optional Hook-Up) spigot assembly, or does not otherwise meet the requirements for a gravity drain, you may have ordered a pre-installed U-Line P60 drain pump. Waste If you need to install a P60 drain pump into your unit, see 6KXW 2ɞ Valve DRAIN PUMP section in the User Manual.
QUICK START GUIDE u-line.com Door Swing Wall For Integrated models that are installed adjacent to a wall, 1/2" (13 mm) 1/4" (6 mm) clearance is recommended from wall on hinge side to allow the door to open 90°. Allow for additional space for any knobs or pulls installed on the integrated panel/frame. Stainless Steel models that are installed adjacent to a wall require 2-1/4" (57 mm) door clearance on hinge side to allow for door handle.
QUICK START GUIDE u-line.com Door Adjustments DOOR ALIGNMENT AND ADJUSTMENT Align and adjust the door if it is not level or is not sealing properly. If the door is not sealed, the unit may not cool T-25 Torx Screw properly, or excessive frost or condensation may form in the interior. Properly aligned, the door’s gasket should be firmly in contact with the cabinet all the way around the door (no gaps).
QUICK START GUIDE u-line.com INSTALLATION TIP 4. Remove caps from screw heads on opposite side (2 on top and 2 on bottom). Using #2 Phillips bit remove the If the room floor is higher than the floor in the cutout 4 underlying screws. Reinstall the screws and caps on opening, adjust the rear legs to achieve a total unit rear the opposite side. height of 1/8" (3 mm) less than the opening’s rear height. Shorten the unit height in the front by adjusting the front legs.
QUICK START GUIDE u-line.com 5. The panel should be aligned with the outside edge NOTICE (opposite the hinge) and high enough to align with the It is important to ensure that all drilled holes are highest point in the door. drilled to the correct depth in order to avoid splits in the wood when hardwood is installed. Align Top Of Panel With Highest Point Of Door 8. Locate 6 of the #6x 1-1/2" (38 mm) screws provided with your unit. Align Panel Against Door Edge First 9.
QUICK START GUIDE u-line.
QUICK START GUIDE u-line.com The ice cube thickness is factory set for best overall performance. The factory setting “0” is designed to THINNER BRIDGE THICKER BRIDGE maintain an ice bridge of approximately 1/16" to 1/8" SHALLOWER DIMPLE DEEPER DIMPLE (1.6 mm to 3.2 mm) under normal conditions, resulting in a dimple of approximately 1/4" to 1/2" (6.4 mm to 12.7 mm) in depth. A fuller cube with less of a dimple results in a thicker ice bridge.
QUICK START GUIDE u-line.com Sabbath Mode 1 2 3 4 5 6 7 Up Select Down U-Line Clear Ice Machine models are Star-K certified and can be used during the Sabbath. View a full list of Star-K certified U-Line units at www.star-k.org. To prepare the unit for the Sabbath: 1. Press and hold the until the unit turns off. 2. No new ice will form when the unit is off, but previously made ice will still be accessible/present for over 24 hours.
U-Line Corporation (U-Line) Limited Warranty One Year Limited Warranty For one year from the date of original purchase, this U-Line product warranty covers all parts and labor to repair or replace any part of the product that proves to be defective in materials or workmanship. For products installed and used for normal residential use, material cosmetic defects are included in this warranty, with coverage limited to 60 days from the date of original purchase.