QUICK START GUIDE 1000 Series • CLR1215 • 115 V / 60 Hz
QUICK START GUIDE u-line.com WELCOME TO U-LINE Congratulations on your U-Line purchase. Your product comes from a company with over five decades and three generations of premium modular ice making, refrigeration, and wine preservation experience. U-Line continues to be the American leader, delivering versatility and flexibility for multiple applications including residential, light commercial, outdoor and marine use.
QUICK START GUIDE u-line.com This Quick Start Guide covers the basics of installation and general use of your product. For more details, see the complete User Guide & Service Manual on u-line.com.
QUICK START GUIDE u-line.com Safety and Warning This unit is designed to operate between 50°F (10°C) and NOTICE the unit’s ability to reach low temperatures and/or reduce Please read all instructions before installing, ice production on applicable models. 100°F (38°C). Higher ambient temperatures may reduce operating, or servicing the appliance. For best performance, keep the unit out of direct sunlight and away from heat generating equipment.
QUICK START GUIDE u-line.com Electrical Water Hookup PREPARE PLUMBING ! WARNING The water valve uses a standard 1/4" (6.35 mm) compression fitting. A 10' (3 m) braided flexible water SHOCK HAZARD — Electrical Grounding supply line is included with the unit. Required. Never attempt to repair or perform maintenance on the unit until the electricity has been disconnected.
QUICK START GUIDE u-line.com 3. Locate water ! CAUTION valve in the front of the unit and Do not use any plastic water supply line. The line thread water is under pressure at all times. Plastic may crack supply line or rupture with age and cause damage to your through. home. Route the water Do not use tape or joint compound when supply line attaching a braided flexible water supply line through the unit that includes a rubber gasket.
QUICK START GUIDE u-line.com Water Supply Connection 8. Install retaining clip. ! WARNING Connect to potable water supply only. ! CAUTION Review, obey, and understand the local plumbing codes before you install your unit. Connect to the cold water supply. The water pressure should be between 20 and 120 psi (138 and 827 kPa). The water line MUST have a shutoff valve on the supply line. OUTDOOR MODELS ! CAUTION PREPARE PLUMBING The water valve uses a standard 1/4" (6.
QUICK START GUIDE u-line.com 7. Install retaining clip. 1. Turn off water supply and disconnect electrical supply to product prior to attempting installation. 2. Remove the grille/access panel in the front and the back panel.Locate water valve in the front of the unit and thread water supply line through. NOTICE Route the water supply line through the unit so it does not come into contact with any internal components other than the solenoid valve. Normal operation creates some vibration.
QUICK START GUIDE u-line.com Drain GRAVITY DRAIN Model numbers including “-00” or “-07” do not include a factory installed drain pump. Normal Proper Drain Model numbers including “-40” or “-47” include a factory installed drain pump. With Trap Poor Drainage, Water Will Back Up DRAIN CONNECTION ! CAUTION With Trap and Vent Proper Drain If your U-Line unit did not come with a factory installed drain pump you must use a gravity A gravity drain may be used if: style drain connection.
QUICK START GUIDE u-line.com FACTORY INSTALLED DRAIN PUMP Y-Branch Tailpiece P60 Pump Required If your drain line will run up to a stand pipe, disposal or Air Gap (Optional Hook-Up) spigot assembly, or does not otherwise meet the requirements for a gravity drain, you may have ordered a pre-installed U-Line P60 drain pump. Waste If you need to install a P60 drain pump into your unit, see 6KXW 2ɞ Valve DRAIN PUMP section in the User Manual.
QUICK START GUIDE u-line.com General Installation INSTALLATION 1. Plug in the power/electrical cord. LEVELING INFORMATION 1. Use a level to 2. Gently push the unit into position. Be careful not to confirm the unit is entangle the cord or water and drain lines. level. Level should be placed along top 3. Re-check the leveling, from front to back and side to edge and side edge side. Make any necessary adjustments. The unit’s top as shown.
QUICK START GUIDE u-line.com It is important to ensure that all drilled holes are 8. Align door with cabinet. Tighten the top 3 screws, drilled to the correct depth in order to avoid securing the top hinge to the cabinet. splits in the wood when hardwood is installed. 11.Locate 6 of the #6x 1-1/4" (32 mm) screws provided Align Top Of Panel With Highest Point Of Door/Drawer with your unit. 12.
QUICK START GUIDE u-line.com Control Operation Light Power Clean LED Up Down CONTROL FUNCTION GUIDE FUNCTION COMMAND DISPLAY/OPTIONS ON/OFF Press Unit will immediately turn ON or OFF. Adjust ice thickness See “Ice” section View temperature in unit Press Toggle between F/C Hold Sabbath Mode See “Sabbath Mode” section and release and and The display will flash and then toggle from set point together and release to temperature in unit.
QUICK START GUIDE u-line.com The ice cube thickness is factory set for best overall Your clear ice machine is pre-set to produce ice between performance. The factory setting is designed to maintain the optimal dimensions illustrated below: an ice bridge of approximately 1/16" to 1/8" (1.6 mm to Cube Details 3.2 mm) under normal conditions, resulting in a dimple of 1/4" TO 1/2" (6.4 mm to 12.7 mm) DIMPLE approximately 1/4" to 1/2" (6.4 mm to 12.7 mm) in depth.
QUICK START GUIDE u-line.com Sabbath Mode 1 2 3 4 5 6 7 Up Select Down U-Line Clear Ice Machine models are Star-K certified and can be used during the Sabbath. View a full list of Star-K certified U-Line units at www.star-k.org. To prepare the unit for the Sabbath: 1. Press and hold the until the unit turns off. 2. No new ice will form when the unit is off, but previously made ice will still be accessible/present for over 24 hours.
U-Line Corporation (U-Line) Limited Warranty One Year Limited Warranty For one year from the date of original purchase, this U-Line product warranty covers all parts and labor to repair or replace any part of the product that proves to be defective in materials or workmanship. For products installed and used for normal residential use, material cosmetic defects are included in this warranty, with coverage limited to 60 days from the date of original purchase.
