Specifications

ManualsBrandsU-Line ManualsPower ToolsH-1027

0513 IH-1027PAGE 1 OF 11

Before operating this stapler familiarize yourself with the safety

warnings and instructions in this manual. Keep these instructions with

the stapler for future reference. If you have any questions, contact

Uline at 1-800-295-5510.

WARNING

STAPLER SPECIFICATIONS

Dimensions: L x H x W 13.5 x 8.75 x 6"

Weight (Without Fasteners) 6 lb.

Compressed Air:

Maximum psi: 110 psi

Recommended

Operating Pressure: 71–100 psi

Air Consumption: 2.4 CFM

Staple Specification: S-1397 A58 Stick

Staple Specification: S-1396 C34 Stick

Staple Specification: S-289 C58 Stick

Staple Capacity: 100 Staples

Noise Levels: 89 dBa

H-1027, H-1028

H-3064

PNEUMATIC STICK

STAPLER

Summary of content (11 pages)

PAGE 1
H-1027, H-1028 H-3064 PNEUMATIC STICK STAPLER stapler specifications Dimensions: L x H x W 13.5 x 8.75 x 6" Weight (Without Fasteners) 6 lb. Compressed Air: Maximum psi: 110 psi Recommended Operating Pressure: 71–100 psi Air Consumption: 2.
PAGE 2
safety instructions general safety Lubrication & Maintenance 1. Read the manual and understand all safety instructions before operating the stapler. If you have questions, contact Uline at 1-800-295-5510. 1. Lubricate the stapler prior to initial operation. 2. Never use flammable gases as a power source for the stapler. Only use filtered, compressed air. 3. Never use gasoline or other flammable liquids to clean the stapler. Vapors left on the stapler could ignite and cause the stapler to explode. 4.
PAGE 3
safety instructions continued Loading the Stapler 1. Disconnect the air supply. 2. Pull the pusher back until it stops on pusher pivots. Rotate pusher to position. (See Figure 1) 3. Insert 2 sticks of appropriate staples into the magazine. Let the sticks slide forward to the front of the magazine. (See Figure 2) 4. Pull the pusher back to an upright position and gently let the pusher slide forward against the staples.
PAGE 4
safety instructions continued Clinch Adjustment Use 2.5 mm Allen wrench and turn collar through window clockwise to tighten clinch. (See Figure 6) Loosen Tight Medium Tighten Loose Figure 6 Depth Adjustment 1. Loosen front screw with a 6 mm Allen wrench. (See Figure 7) 2. Push the body up and adjust to the desired depth. (See Figure 8) Figure 7 3. When the top edge of the adjustment plate is at its highest setting the teeth are at their shallowest penetration. (See Figure 9) 4. If set at No.
PAGE 5
operating instructions Warning 1. Protect your eyes and ears. a. Wear safety glasses with side shields b. Wear hearing protection. c. Ensure that anyone in the vicinity wears safety protection. 2. To prevent accidental injuries, never place a hand or any other body part in the staple clinching area or adjustment window. 3. Never point the stapler towards you or anyone else. 4. Always handle the stapler with care. Never pull the trigger unless stapler is ready for operation. 5.
PAGE 6
OPerating instructions continued Clearing a Jam 3. Insert needle nose pliers or screwdriver to clear jam. (See Figure 12) 1. Disconnect air supply. 2. Pull pusher back and rotate to a locked position. (See Figure 11) Figure 11 4. Slowly release pusher back to position. Figure 12 Warning Stop using the stapler immediately if any of the following problems occur. Serious personal injury could occur. Any repairs or replacements must be done by a qualified person or authorized service center only.
PAGE 7
OPerating instructions continued Teeth Replacement 1. Loosen screws and nut with an 8 mm wrench and 4 mm Allen wrench. (See Figure 13) 3. Loosen screws with 3 mm Allen wrench. (See Figure 15) 2. Remove the magazine assembly. (See Figure 14) 4. Change teeth one at a time to prevent reverse teeth.
PAGE 8
OPerating instructions continued Driver Replacement 1. Disconnect the air supply. 2. Loosen screw and nut with a 8 mm spanner wrench and a 4 mm Allen wrench. (See Figure 16) 3. Remove the magazine assembly. (See Figure 17) 4. Loosen the set screw with a 3 mm Allen wrench to unlock the adjusting rod. 5. Slide the linkage mechanism and adjusting rod simultaneously from the collar. (See Figure 18) 6. Loosen the screws with a 3 mm Allen wrench. (See Figure 19) 7.
PAGE 9
OPerating instructions continued Pusher Spring Replacement 1. Loosen the screws and nut with a 8 mm spanner wrench and a 4 mm Allen wrench. (See Figure 21) 5. Loosen the screw and nut with a 2.5 mm Allen wrench and 7 mm socket wrench. (See Figure 24) 2. Remove the magazine assembly. (See Figure 22) 6. Loosen the rod with a 6 mm offset wrench and remove the pusher guides. Remove the pusher. (See Figure 25) 3. Pull the pusher back until it stops on the rod, then rotate the pusher to position.
PAGE 10
OPerating instructions continued Valve AND Tube O-Ring Replacement 1. Loosen screws with a flat screwdriver. (See Figure 27) 2. Remove spring with needle nose pliers. (See Figure 28) Figure 27 3. Remove C-ring with C-ring pliers. (See Figure 29) 4. Remove valve and tube with needle nose pliers.
PAGE 11
OPerating instructions continued Piston Replacement 1. Remove screws and nut with 8 mm spanner wrench and 4 mm Allen wrench. (See Figure 31) 6. Loosen screw with a 3 mm Allen wrench and remove the block through the window. 2. Remove magazine assembly. (See Figure 32) 7. Loosen screws with a 3 mm Allen wrench and remove the cap. (See Figure 34) 3. Loosen set screw with a 3 mm Allen wrench to unlock the adjusting rod. 4. Slide linkage mechanism and adjusting rod simultaneously from collar. 8.