PHONE 1-800-295-5510 FAX 1-800-295-5571 WEB uline.com AIR DRIVE CARTON STAPLER MODEL: H-1028 MANUAL WARNING Before operating this stapler familiarize yourself with the safety warnings and instructions in this manual. Keep these instructions with the stapler for future reference. If you have any questions, contact Uline at 1-800-295-5510.
PHONE 1-800-295-5510 FAX 1-800-295-5571 WEB uline.
PHONE 1-800-295-5510 FAX 1-800-295-5571 WEB uline.com Tool Specifications Model of Tool Dimensions: LxHxW Weight (without Fasteners) H-1028 ADB 18-32 13.5x8.
PHONE 1-800-295-5510 FAX 1-800-295-5571 WEB uline.com SAFETY INSTRUCTIONS 1. Read the manual and understand all safety instructions before operating the tool. If you have questions, contact Uline at 1-800-295-5510. 2. Never use flammable gases as a power source for the stapler. Only use filtered, compressed air. 3. Never use gasoline or other flammable liquids to clean the stapler. Vapors left on the stapler could ignite and cause the tool to explode 4.
PHONE 1-800-295-5510 FAX 1-800-295-5571 WEB uline.com Lubrication & Maintenance: 1. Lubricate the stapler prior to initial operation. 2. Disconnect the stapler from the air supply prior to servicing. 3. Turn the stapler so that the inlet is facing up and put one drop of high-speed spindle oil, UNOCOL RX22, or 3-in-1 oil into air inlet. Never use detergent oil or additives. 4. Operate the tool briefly after adding oil. 5. Wipe off excessive oil at the exhaust. Excessive oil will damage the O-rings.
PHONE 1-800-295-5510 FAX 1-800-295-5571 WEB uline.com Loading the Tool 1. Disconnect the air supply. 2. Pull the Pusher back until it stops on pusher pivots. Rotate pusher to position. 3. Insert 2 sticks of appropriate staples into the magazine. Let the sticks slide forward to the front of the magazine. 4. Pull the pusher back to an upright position and gently let the pusher slide forward against the staples.
PHONE 1-800-295-5510 FAX 1-800-295-5571 WEB uline.com Staple Leg Length 1. 2. 3. 4. 5. Loosen the set screw with a 3mm Allen wrench. Adjust 180° with a screw driver to the desired setting. If you are using ¾” staples set L up. If you are using 5/8” staples set S up. (diagram) Tighten the set screw. Back to Top Clinch Adjustment Use 2.5 mm Allen wrench and turn collar through window clockwise to tighten clinch.
PHONE 1-800-295-5510 FAX 1-800-295-5571 WEB uline.com Depth Adjustment 1. Loosen front screw with a 6mm Allen wrench. 2. Push the body up and adjust to the desired depth. 3. When the top edge of the adjustment plate is at it’s highest setting the teeth are at their shallowest penetration. If set at No. 1 the teeth are at their deepest penetration.
PHONE 1-800-295-5510 FAX 1-800-295-5571 WEB uline.com Operating Instructions Warning 1. Protect your eyes and ears. Wear: a. Safety glasses with side shields b. hearing protection. Ensure that anyone in the vicinity wears safety protection. 2. To prevent accidental injuries never place a hand or any other body part in the staple clinching area or adjustment window. 3. Never point the stapler towards you or anyone else. 4. Always handle the stapler with care.
PHONE 1-800-295-5510 FAX 1-800-295-5571 WEB uline.com Clearing a Jam 1. 2. 3. 4. Disconnect Air Supply Pull Pusher back and rotate to a locked position. Insert needle nose pliers or screw driver to clear jam. Slowly release Pusher back to position.
PHONE 1-800-295-5510 FAX 1-800-295-5571 WEB uline.com Troubleshooting Warning Stop using the tool immediately if any of the following problems occur. Serious personal injury could occur. Any repairs or replacements must be done by a qualified person or authorized service center only.
PHONE 1-800-295-5510 FAX 1-800-295-5571 WEB uline.com Teeth Replacement 1. 2. 3. 4. Loosen screws and nut with an 8mm spanner and 4mm Allen wrench. Remove the magazine assembly. Loosen screws with 3mm Allen wrench Change teeth one at a time to prevent reverse teeth.
PHONE 1-800-295-5510 FAX 1-800-295-5571 WEB uline.com Driver Replacement 1. Disconnect the Air Supply 2. Loosen screw and nut with a 8mm spanner wrench and a 4mm Allen wrench. 3. Remove the magazine assembly. 4. Loose the set screw with a 3mm Allen wrench to unlock the adjusting rod. 5. Slide the linkage mechanism and adjusting rod simultaneously from the collar. 6. Loosen the screws with a 3mm Allen wrench. 7. Take off the Spring Pin with a hammer and 6 mm straight rod.
PHONE 1-800-295-5510 FAX 1-800-295-5571 WEB uline.com Pusher Spring Replacement 1. Loosen the screws and nut with a 8mm Spanner wrench and a 4mm Allen wrench. 2. Remove the Magazine Assembly. 3. Pull the Pusher back until it stops on the rod, then rotate the Pusher to position. 4. Push the magazine seat back and remove it from the magazine. 5. Loosen the screw and nut with a 2.5mm Allen wrench and 7mm socket wrench. 6. Loosen the Rod with a 6mm Offset wrench and remove the Pusher guides.
PHONE 1-800-295-5510 FAX 1-800-295-5571 WEB uline.com Valve & Tube O-Ring Replacement 1. 2. 3. 4. Loosen screws with a flat screw driver. Remove spring with Needle nose pliers. Remove C-Ring with C-Ring Pliers. Remove valve and tube with needle nose pliers.
PHONE 1-800-295-5510 FAX 1-800-295-5571 WEB uline.com Piston Replacement 1. 2. 3. 4. 5. 6. Remove screws & nut with 8 mm Spanner wrench and 4 mm Allen wrench. Remove magazine assembly. Loose set screw with a 3mm Allen wrench to unlock the adjusting rod. Slide linkage mechanism and adjusting rod simultaneously from collar. Loosen collar with a 3mm Allen wrench to remove the spring. Loose screw with a 3mm Allen wrench and remove the block through the window. 7.
