Installation Guide SP18 Ice Maker for Marine or Recreational Vehicle Use www.U-LineService.com Phone (414) 354-0300 • FAX (414) 354-7905 Service & Parts Tech Lines Phone (800) 779-2547 • FAX (414) 354-5696 OnlineService@U-Line.
SP18 Ice Maker Contents 1 Follow Safety Precautions Exterior Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Cut-Out Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Product Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Door Swing/Clearances Information . . . . . . . . . . . . . . 4 Reversing the Door. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Other Site Requirements . . . . . . . . . . . . . . . . . . . . . . . .
SP18 Ice Maker General Precautions 2 Inspect and Plan Use this appliance for its intended purpose only and follow these general precautions along with those listed throughout this guide: You have received a carton containing your SP18 Ice Maker with a package inside containing a User Manual, a Product Registration Card and water connection parts. Complete and mail the Product Registration Card or register online at www.U-LineService.com.
SP18 Ice Maker Product Dimensions 3 Prepare Site Your U-Line product has been designed for built-in installation. When built-in, your unit does not require additional air space for top, sides or rear. However, the front grille must NOT be obstructed and clearance is required for water and electrical connections in the rear. 15-1/16" 13-13/16" Note: Unit can NOT be installed behind a closed cabinet door.
SP18 Ice Maker Reversing the Door All units may be left- or right-hand opening. To reverse the door: 1. Remove travel pin from cabinet (two screws). See Figure 4. Slide assembly through flange and set aside to be used later. 2. Remove top hinge from cabinet (three screws). See Figure 5. Hold door to keep it from falling. Slide hinge through flange. 3. Lift the door off the bottom hinge. Figure 7 Figure 8 5. Install hinge on opposite side, bottom of cabinet. See Figure 8.
SP18 Ice Maker Other Site Requirements Power Supply The unit requires a grounded and polarized 110/115 VAC, 60 Hz, 15A circuit (normal household current) or 220/230 VAC, 50/60 Hz. See Electrical Specifications on Page 8. Water Supply The unit requires a 1/4-inch OD water supply line and a shut-off valve. For more information see Page 7. Environmental Requirements Figure 11 The surrounding air temperature must be at least 45°F (7°C) but must not exceed 110°F (40°C).
SP18 Ice Maker 4 Adjust Door 5 Prepare Plumbing CAUTION Checking Door Alignment Plumbing installation must observe all state and local codes. All water connections MUST BE made by a licensed/ qualified plumbing contractor. Failure to follow recommendations and instructions may result in damage and/or harm. The unit’s door is aligned at the factory before shipment. However, its alignment could have been disturbed during shipment.
SP18 Ice Maker 6 Prepare Power Supply Water Line Electrical Specifications CAUTION Electrical installation must observe all state and local codes. This unit requires connection to a grounded (threeprong), polarized receptacle that has been placed by a qualified electrician. Figure 15 Figure 16 The unit requires a grounded and polarized 110/115 VAC, 60 Hz, 15A power supply (normal household current) or a 220/230 VAC, 50/60 Hz power supply.
SP18 Ice Maker 7 Level the Unit 8 Install the Unit Leveling Information Installation of the SP18 1. Open the water supply valve in the main water source. IMPORTANT 2. Plug in the power cord. It is extremely important that the unit sits on a level surface, as it does not have feet levelers. If it is not level, the ice mold will not fill evenly. 3. Gently push the unit into position. Be careful not to kink the water supply line or entangle the electrical cord.
SP18 Ice Maker Start-Up Troubleshooting 9 Start-Up for the First Time Q: Problem Initial Start-Up Unit does not appear to turn on when plugged in. The on/off switch is located on the front grille. Ensure that the switch is turned on. A: Solution No setting adjustments should be necessary at this time. For information about Adjusting the Temperature Control, see the User Manual. Make sure outlet has power (circuit breaker has not tripped). Make sure the on/off switch is turned on.
Who to Call Service Information If the need for service arises, contact the dealer from whom the unit was purchased. State the Model Number and Serial Number and explain the problem. The Model and Serial Number plate is located inside unit behind the ice bucket. If you need to locate a service company, you can go online at www.U-LineService.com and search for a service company by zip code.