USE AND CARE GUIDE ® MODULAR 3000 SERIES 120V, 3018CLR MODELS U-3018CLROL-00 U-3018CLROL-01 U-3018CLROL-40 U-3018CLROL-41 U-3018CLRS-00 U-3018CLRS-01 U-3018CLRS-40 U-3018CLRS-41 THE MODULAR 3000 SERIES ARE INTENDED FOR BUILT-IN INSTALLATIONS ONLY The American Built-In Undercounter Leader Since 1962 U-LINE.
Introduction Please Record Your Model Information For nearly five decades and three generations, U-Line continues to be the leader in innovation, quality and value in the premium built-in undercounter ice making, refrigeration and wine preservation market. U-Line has captivated those with an appreciation for the finer things with exceptional functionality, style, inspired innovation and attention to even the smallest details.
Table of Contents Safety Precautions Safety Alert Definitions.........................................................................................................................................1 General Precautions .............................................................................................................................................1 Product Features Guide Coverage .....................................................................................................................
General Precautions Safety Precautions Use this appliance for its intended purpose only and follow these general precautions with those listed throughout this guide: NOTICE • PLEASE READ all instructions before installing, operating, or servicing the appliance. • Proper installation procedures must be followed when completing an installation or relocation of a unit. An INSTALLATION GUIDE for the unit, providing complete installation information, is available from U-Line Corporation direct.
3000 Series Features Product Features Advanced OLED control system: State of the art OLED control system display. Guide Coverage Fully integrated design: Units are designed to blend seamlessly with surrounding decor. This guide covers the following list of models. U-3018CLROL-00 Stainless steel: Stainless steel models offer a commercial stainless steel handle and door wrap.
to cycle through each available timer 3. Use U-Select Lighting setting. Selections include “On With Door”, “On 3 Hours”, “On 6 Hours”, or “On 24 Hours”. Product Operation Air Flow 4. To exit, press Select or simply wait for the menu to time out. Customer Menu NOTICE The unit requires proper air flow to perform at its highest efficiency. Do not block the front grille, internal fans or vents at any time, or the unit will not perform as expected. Do not install the unit behind a door.
Languages Energy Saver Mode Up Up Energy Saver Mode Indicator Select Select RETURN TO MENU LANGUAGES ENGLISH ICE PRODUCTION (12m remaining) Down Down Energy Saver mode reduces overall energy consumption by reducing the amount of ice stored in the bin, along with decreasing the lighting. 1. To change display language select Languages from the Customer Menu. 1. To enter Energy Saver first select Energy Saver from the Customer Menu. 2. Use Down to select “Off” in the menu. 3. Press Select . 4.
Fahrenheit / Celsius Silent Mode Up Up Select Select RETURN TO MENU FARENHEIT/CELSIUS DEGREES = °F RETURN TO MENU SILENT MODE SILENCE? Down Down Temperature and Set point information can be displayed in either Fahrenheit or Celsius. To change from Fahrenheit to Celsius enter the Fahrenheit / Celsius menu from within the Customer Menu. 1. Use Down to select “Degrees”. 2. Press Select . The selection will begin to flash. 3. Use Up (Celsius). 4.
Factory Default Up Select RETURN TO MENU FACTORY DEFAULT RESTORE? Down The Factory Default option restores all settings to the original settings the unit came with. To restore Factory Default settings, enter the Factory Default menu from within the Customer Menu. 1. Use Down to select “Restore?”. 2. Press Select . All settings will now be at Factory Default. Help Up Select RETURN TO MENU Help Model 3018CLR 1-800-779-2547 Down To access the Help menu select Help from the Customer Menu.
Ice cubes in any given batch will vary, so it is necessary to choose cubes from the sample area for comparison when making adjustments. If further adjustments are desired, repeat procedure. NOTICE • Discard all ice produced in the first harvest. • Should power to the unit be interrupted during the selfclean cycle, the complete cleaning cycle will repeat after power is restored.
Removing and Installing Grille 3000 Series Maintenance ! WARNING Leveling • Disconnect electrical power to the unit before removing the grille. • Edges of sheet metal may be sharp. NOTICE Unit must be level for proper door and unit operation. Removing the grille. 1. Use a level to check the levelness of the unit from front to back and from side to side. Place the level along top edge and side edge as shown (1). 1. Disconnect power to unit. 2.
3. Gently pull bottom of wrap away from door. 3000 Series Doors 4. The wrap hinges on top of the door. Carefully pull wrap away and then up. See below. Door Alignment and Adjustment Align and adjust the door if it is not level, or is not sealing properly. If the door is not sealed the unit may not cool properly, or excessive frost or condensation may form in the interior.
Clear Ice Maker Cleaning Cycle Cleaning Exterior Cleaning • Stainless door panels, and handles can discolor when exposed to chlorine gas, pool chemicals, saltwater or cleaners with bleach. • Keep your stainless unit looking new by cleaning with a good quality all-in-one stainless steel cleaner polish monthly. For best results use Claire® Stainless Steel Polish and Cleaner, which can be purchased from U-Line Corporation (Part Number 173348). Comparable products are acceptable.
5. Re-install the standpipe into the water trough. Evaporator Standpipe Water trough 6. Clean the Interior Bin as follows: • Dilute one packet of CLR cleaner into two quarts of water. • Using a sponge or cloth, clean interior of ice bin, tubing and door. This cleaner will remove all mineral deposits and other contaminants from the surfaces. • Using a bottle brush, clean out the trough drain tube and pump tubing where needed. Brush 7. Turn unit on by touching POWER . 8.
Condenser Cleaning Storage, Vacation and Moving Interval - As Needed If not using the unit for an extended period, or otherwise stored, follow these steps completely: To maintain operational efficiency, keep the front grille free of dust and lint, and clean the condenser when necessary. Depending on environmental conditions, more or less frequent cleaning may be necessary. ! WARNING ! WARNING Electrical Shock Hazard. Disconnect power before servicing. Before operating, replace all panels.
Troubleshooting Guide Service ! DANGER Before Calling for Service If you think your U-Line product is malfunctioning, read the OPERATION section of this guide to understand clearly the function of the control. If the problem persists, read the NORMAL OPERATING SOUNDS and TROUBLESHOOTING GUIDE section of this guide to help you quickly identify common problems, and possible causes and remedies. Most often, this will resolve the problem without the need to call for service.
USE AND CARE GUIDE ® PRODUCT INFORMATION Complete Installation Guides, Use and Care Guides, Specifications & Features and Benefits, CAD Drawings, Overlay Panel/Frame and Toe-Kick Specifications and Instructions, Compliance Documentation and Applicable Energy Guides are available for reference and download at u-line.com. SERVICE INFORMATION Please consult your Use and Care Guide for troubleshooting information. Answers to Customer Frequently Asked Questions are available at u-line.
