QUICK START GUIDE 1000 Series • CLR1215 • 115 V / 60 Hz
QUICK START GUIDE u-line.com WELCOME TO U-LINE Congratulations on your U-Line purchase. Your product comes from a company with over five decades and three generations of premium modular ice making, refrigeration, and wine preservation experience. U-Line continues to be the American leader, delivering versatility and flexibility for multiple applications including residential, light commercial, outdoor and marine use.
QUICK START GUIDE Contents 1 Model List 2 Safety and Warning 2 Environmental Requirements 3 Water Hookup 5 Drain 7 Door Swing 8 General Installation 9 Control Operation 9 First Use 9 Ice 10 Sabbath Mode 11 Warranty u-line.
QUICK START GUIDE u-line.com Model List This guide provides the basics to get you started. Looking for more information? Visit u-line.com to view detailed User Guides for all U-Line products. Clear Ice U-CLR1215S-00A U-CLR1215S-40A U-CLR1215INT-00A U-CLR1215INT-40A U-CLR1215B-00A U-CLR1215B-40A U-CLR1215W-00A U-CLR1215W-40A Outdoor Series U-CLR1215RSOD-00A U-CLR1215RSOD-40A Visit http://www.u-line.com/product-literature/userguides or scan this QR code to view all user guides online.
QUICK START GUIDE u-line.com Safety and Warning Environmental Requirements NOTICE This unit is designed to operate between 50°F (10°C) and 100°F (38°C). Higher ambient temperatures may reduce PLEASE READ all instructions before installing, the unit’s ability to reach low temperatures and/or reduce operating, or servicing the appliance. ice production on applicable models.
QUICK START GUIDE u-line.com Water Hookup Do not use Teflon tape or joint compound on the INDOOR MODELS adequate seal. Other materials could cause PREPARE PLUMBING blockage of the valve. water fitting. The rubber washer provides an Please use the braided stainless steel water supply line which comes attached. The water line is fitted with a Failure to follow recommendations and standard 1/4" (6.35 mm) compression fitting.
QUICK START GUIDE u-line.com Water Supply Connection 5. Route water supply line in cable clamp and secure with screw. ! CAUTION Review, obey, and understand the local plumbing codes before you install your unit. Connect to the cold water supply. The water pressure should be between 20 and 120 psi. The water line MUST have a shut-off valve on the supply line. ! CAUTION Do not use any plastic water supply line. The line is under pressure at all times.
QUICK START GUIDE u-line.com 8. Install retaining clip. 3. Locate water valve in the front of the unit and thread water supply line through. NOTICE Route the water supply line through the unit so it does not come into contact with any internal components other than the solenoid valve. Normal operation creates some vibration. A water supply line contacting an internal component or cabinet wall can cause excessive noise during operation or damage to the line. 4.
QUICK START GUIDE u-line.com NOTICE ! CAUTION Drain can NOT be located directly below the unit. Unit has a solid base that will not allow the unit Failure to connect water supply or drain line to drain below itself. connections properly can result in personal injury and property damage. Gravity drain There is a possibility that hose connections may connections must be routed downward from the have loosened during shipment. rest of the unit at the rate of 1/4" per foot (1 cm per 50 cm).
QUICK START GUIDE u-line.com Door Swing Disposal Assembly P60 Pump Required Air Gap (Optional Hook-Up) Wall Wall 1/4" Min. (6 mm) 2-1/8" Min. (54 mm) Waste Hot Water Cold Water 6KXW 2ɞ Valve 90° Door Swing 90° Door Swing Y-Branch Tailpiece P60 Pump Required Air Gap (Optional Hook-Up) Units have a zero clearance for the door to open 90°, when installed adjacent to cabinets.
QUICK START GUIDE u-line.com General Installation INSTALLATION 1. Open the water supply valve in the main water source. LEVELING INFORMATION 1. Use a level to 2. Plug in the power cord. confirm the unit is level. Level should 3. Gently push the unit into position. Be careful not to be placed along top edge and side edge kink the water supply line, the drain line, or entangle as shown. the power cord. 4. Re-check the leveling, from front to back and side to side. Make any necessary adjustments.
QUICK START GUIDE u-line.com Control Operation Alert Light Power Clean LED Up Down CONTROL FUNCTION GUIDE FUNCTION COMMAND DISPLAY/OPTIONS ON/OFF Press Unit will immediately turn ON or OFF. Adjust ice thickness See “Ice” section View temperature in unit Press Toggle between F/C Hold Sabbath Mode See “Sabbath Mode” section and release and and The display will flash and then toggle from set point together and release to temperature in unit.
QUICK START GUIDE u-line.com Adjust ice thickness as follows: The ice cube thickness is factory set for best overall performance. The factory setting “0” is designed to maintain an ice bridge of approximately 1/16" to 1/8" 1. Press (1.6 mm to 3.2 mm) under normal conditions, resulting in and hold for 5 seconds (display will show current settings). a dimple of approximately 1/4" to 1/2" (6.4 mm to 12.7 mm) in depth. A fuller cube with less of a dimple 2. Press results in a thicker ice bridge.
QUICK START GUIDE u-line.com Warranty unit is completed and mailed back or electronically U-LINE CORPORATION LIMITED WARRANTY apply to cosmetic damages. A proof of purchase may 1. U-Line Corporation (“U-Line”) warrants each U-Line be required. submitted to U-Line. This 30 day warranty does not product to be free from defects in materials and workmanship for a period of one year (two years on 4. The following conditions are excluded from this limited Modular 3000 Series) from the date of purchase.
QUICK START GUIDE u-line.com of pool water, or directing a spray from a hose or similar device into and around the unit. 7. If a product defect is discovered during the applicable warranty period, you must promptly notify either U-Line at 8900 N. 55th Street, Milwaukee, Wisconsin 53223 USA or at +1.800.779.2547 or the dealer from whom you purchased the product. In no event shall such notification be received later than 30 days after the expiration of the applicable warranty period.