Installation Guide WH95TP, BI95BTP and BCM95 Ice Makers for Marine or Recreational Vehicle Use www.U-LineService.com Phone (414) 354-0300 • FAX (414) 354-7905 Service & Parts Tech Lines Phone (800) 779-2547 • FAX (414) 354-5696 OnlineService@U-Line.
WH95TP, BI95BTP and BCM95 Ice Makers Contents Exterior Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Cut-Out Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . Product Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . Door Swing/Clearances Information . . . . . . . . . . . . . . Reversing the Door. . . . . . . . . . . . . . . . . . . . . . . . . . . . . Other Site Requirements . . . . . . . . . . . . . . . . . . . . . . . .
WH95TP, BI95BTP and BCM95 Ice Makers General Precautions 2 Inspect and Plan Use this appliance for its intended purpose only and follow these general precautions along with those listed throughout this guide: You have received a carton containing your WH95TP, BI95BTP or BCM95 Ice Maker with a package inside containing a User Manual, a Product Registration Card and water connection parts. Complete and mail the Product Registration Card or register online at www.ULineService.com.
WH95TP, BI95BTP and BCM95 Ice Makers Product Dimensions 3 Prepare Site Your U-Line product has been designed for built-in installation. When built-in, your unit does not require additional air space for top, sides or rear. However, the front grille must NOT be obstructed and clearance is required for water and electrical connections in the rear. 15-1/16" 13-13/16" 17" Including Handle Note: Unit can NOT be installed behind a closed cabinet door.
WH95TP, BI95BTP and BCM95 Ice Makers Reversing the Door All units may be left- or right-hand opening. Note: The grille should not yet be installed. If it has been installed, remove it for door reversing. See Page 10. To reverse the door: 1. Remove travel pin from cabinet (two screws). See Figure 4. Slide assembly through flange and set aside to be used later. 2. Remove top hinge from cabinet (three screws). See Figure 5. Hold door to keep it from falling. Slide hinge through flange. 3.
WH95TP, BI95BTP and BCM95 Ice Makers Other Site Requirements Power Supply The unit requires a grounded and polarized 115 VAC, 60 Hz, 15A circuit (normal household current) or 220 VAC, 50/60 Hz. See Electrical Specifications on Page 9. Water Supply The unit requires a 1/4-inch OD water supply line and a shut-off valve. For more information see Page 8. Environmental Requirements Figure 11 The surrounding air temperature must be at least 45°F (7°C) but must not exceed 110°F (40°C).
WH95TP, BI95BTP and BCM95 Ice Makers 4 Prepare and Install Door Panel (BI95BTP units only) Units will accept a Custom 1/4" Thick Insert to harmonize with or accent the surrounding decor. If this treatment is not included in this installation, go on to 5 Adjust Door. Custom 1/4" Thick Door Panel Insert Door Panel Preparation Figure 14 A custom door panel can be inserted into the doorframe.
WH95TP, BI95BTP and BCM95 Ice Makers 5 Adjust Door 6 Prepare Plumbing CAUTION Checking Door Alignment Plumbing installation must observe all state and local codes. All water connections MUST BE made by a licensed/ qualified plumbing contractor. Failure to follow recommendations and instructions may result in damage and/or harm. The unit’s door is aligned at the factory before shipment. However, its alignment could have been disturbed during shipment or during door panel installation.
WH95TP, BI95BTP and BCM95 Ice Makers 7 Prepare Power Supply Electrical Specifications CAUTION Electrical installation must observe all state and local codes. This unit requires connection to a grounded (threeprong), polarized receptacle that has been placed by a qualified electrician. Water Line Figure 18 Figure 19 The unit requires a grounded and polarized 115 VAC, 60 Hz, 15A power supply (normal household current) or a 220 VAC, 50/60 Hz power supply.
WH95TP, BI95BTP and BCM95 Ice Makers 8 Level the Unit 9 Install the Unit Leveling Information Installation of the WH95TP, BI95BTP or BCM95 IMPORTANT 1. Open the water supply valve in the main water source. It is extremely important that the unit sits on a level surface, as it does not have feet levelers. If it is not level, the ice mold will not fill evenly. 2. Plug in the power cord. 3. Gently push the unit into position. Be careful not to kink the water supply line or entangle the electrical cord.
WH95TP, BI95BTP and BCM95 Ice Makers 10 Start-Up for the First Time Initial Start-Up The on/off switch is located behind the front grille. A small opening in the top of the grille is provided to access the switch. Ensure that the switch is turned on. Grille Hook-Hinge No setting adjustments should be necessary at this time. For information about Adjusting the Temperature Control, see the User Manual.
Start-Up Troubleshooting Who to Call Q: Problem Service Information Unit does not appear to turn on when plugged in. A: Solution Make sure outlet has power (circuit breaker has not tripped). Make sure the on/off switch is turned on. If the need for service arises, contact the dealer from whom the unit was purchased. State the Model Number and Serial Number and explain the problem. The Model and Serial Number plate is located inside unit behind the ice bucket.
