Datasheet

ManualsBrandsU.S. Converters ManualsAdapterUCBT232EXA

Datasheet & Quick Reference, UCBT232/EXA v3.0 www.usconverters.com

www.usconverters.com Page 1

Bluetooth RS232 Adapter

Datasheet & Quick Reference for UCBT232B and UCBT232EXA

Bluetooth RS232 Adapter

with Internal Chip / External di-pole Antenna

UCBT232B UCBT232EXA

UCBT232B / UCBT232EXA Package Contents:

 RS-232 adapter x 1

 DB9 male/male gender changer

 Battery power line and connector x 1

 User manual x 1

 USB Cable x 1

 Di-pole antenna (UCBT232EXA only)

1. Power options:

The adapter can be powered by one of the following:

 Mini USB cable (5VDC)

 DB9 connector Pin 9 (4.8 - 24VDC, 1.0A, S/N 13082227 or higher only)

 External battery (4.8 - 24VDC, 1.0A, S/N 13082227 or higher only)

2. Typical operating current consumption: 100mAh

Summary of content (8 pages)

PAGE 1
Datasheet & Quick Reference, UCBT232/EXA v3.0 www.usconverters.com Bluetooth RS232 Adapter Datasheet & Quick Reference for UCBT232B and UCBT232EXA Bluetooth RS232 Adapter with Internal Chip / External di-pole Antenna UCBT232B UCBT232EXA UCBT232B / UCBT232EXA Package Contents:  RS-232 adapter x 1  DB9 male/male gender changer  Battery power line and connector x 1  User manual x 1  USB Cable x 1  Di-pole antenna (UCBT232EXA only) 1.
PAGE 2
Datasheet & Quick Reference, UCBT232/EXA v3.0 www.usconverters.com Status LED Power LED (Red) S: Slave M: Master Group: G: Enable N/G: Disable Mini USB (Power In) Reset DEC/DTE Switch Power Source Switch Power Line Connector 3. Default factory settings:  Baud rate: 9600 bps (Notice: serial number 14090200 or lower has 19200 baud as default).
PAGE 3
Datasheet & Quick Reference, UCBT232/EXA v3.0 8. www.usconverters.com LED Status: Status Description Power LED on The power input is equal or larger than 3.5 Volt, (can be checked with the “DETECT” command) Power LED (0.5 sec) blinking The power input is lower than 3.5 Volt, (can be checked with the “DETECT” command) Link LED off No pairing Link LED fast (0.1 sec) blinking Pairing (slave or master mode) Discoverable and waiting for a Link LED fast (0.3 sec) blinking 9.
PAGE 4
Datasheet & Quick Reference, UCBT232/EXA v3.0 AUTO= www.usconverters.com This command is used to enable/disable the auto-connection feature. It is available only when the adapter is in Master mode and only when DIP=N. The system will not re-start after changing this parameter. (Default) Y Master and Slave will connect automatically. N Master and Slave will need to be connected manually with the 'CONNECT' command. ? BAUD= Inquire the current setting.
PAGE 5
Datasheet & Quick Reference, UCBT232/EXA v3.0 www.usconverters.com In the Master mode, the adapter pairs and connects with the designated remote slave address. If the adapter is in the Slave mode, this command is a filter condition to accept the inquiry of the Master device. xxxxxxxxxxx “xxxxxxxxxxxx” is a string of 12 hexadecimal digits. x R Restore the status in which the adapter can connect with any remote address. ? Inquiry the designated address that can be paired and connected.
PAGE 6
Datasheet & Quick Reference, UCBT232/EXA v3.0 ? PIN= www.usconverters.com Inquire the current setting. This command is used to specify a PIN. The default PIN is “1234”. Paired adapters should have a same PIN. The length must be 4 – 16 alphanumeric characters. (Default) 1234 xx….xx “xx….xx” is a 4 - 16 digit string of alphanumeric characters (in capital or lower case) N Cancel authentication by PIN. R Restore the default settings PIN=“1234”. ? Inquire the current PIN.
PAGE 7
Datasheet & Quick Reference, UCBT232/EXA v3.0 VERSION= www.usconverters.com This command is used to inquiry the firmware version. ? Inquire the version codes.
PAGE 8
Datasheet & Quick Reference, UCBT232/EXA v3.0 www.usconverters.com Federal Communications Commission (FCC) Statement RADIO FREQUENCY INTERFERENCE STATEMENT This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.