EXHIBIT C User Manual
ADSL Router AR-1150 User Manual v. 1.
ADSL Router AR-1150 User Manual Copyright Copyright © 2001, All rights reserved. This manual and software described in it are copyrighted with all rights reserved. This manual may not be copied, in whole or in part, without written consent. All product names are trademarks and or registered trademarks of their respective companies.
ADSL Router AR-1150 User Manual Environmental Requirements w Operating Temperature: 0º C to 55º C with airflow w Non-operating Temperature: -10º C to 85º C w Operating Humidity: 10% to 90% non-condensing w Non-operating storage humidity: 5% to 95% non-condensing Power Requirements w Input: 100-240V 0.3A 50-60Hz w Output: +5V 1.4A 2345 Connector Pin-out The ADSL modem card is equipped with a RJ-11 jack for connection to the ADSL data Port.
ADSL Router AR-1150 User Manual About This Manual This manual provides a comprehensive user’ s guide and installation manual for Multi-mode ADSL Router. It has been organized in such a way to make it easy to follow by users worldwide. In the manual, there are many examples given in the commands, largely IP addresses and other values. Please realize that these are for example only and you must use the values provided by your ADSL service provider to achieve a connection.
ADSL Router AR-1150 User Manual Congratulations! Your new ADSL router is a multi-functional piece of equipment. It conveniently interfaces with your computer system for configuration. The modem connects directly to your telephone line via a standard connector. This guide is designed to walk you through installation of your ADSL Router in the easiest and quickest way possible. Please follow the instructions carefully in order to successfully install the Router.
ADSL Router AR-1150 User Manual All packages have been carefully checked for completeness and functionality before shipping. If anything is missing or damaged, please contact the dealer/ service provider from whom the equipment was purchased. N o t e : Y o u m u s t u s e t h e R J-1 1 A D S L c a b l e p r o v i d e d i n t h e p a c k a g e t o c o n n e c t t o t h e adaptor. U A T excludes itself from any liability for incidental, consequential, indirect, special, or punitive damages of any kind.
ADSL Router AR-1150 User Manual Chapter 1 - Installing and Configuring your ADSL Router The major functions of the ADSL Router are performed by using the Ethernet network interface. Your computer must have an Ethernet Network Interface Card (NIC) installed and set up with the TCP/IP protocol before beginning to use the router. The router also provides a serial console port for monitoring and configuring the router via the built -in command line interface.
ADSL Router AR-1150 User Manual Hardware Installation – Single PC Connection Before configuring your ADSL router, you must complete the hardware installation using the following steps. 1. Be sure the power switch, marked O N / O F F, on the rear of the unit is depressed, in the OFF position. 2. Connect the power adaptor to power receptacle on the rear of the unit marked P W R , then plug the AC end into the wall electrical outlet. 3. You will now connect the Ethernet cable.
ADSL Router AR-1150 User Manual Chapter 2 - Software Installation Auto install Setup program: Please insert the CD coming with your package into your computer's CD-ROM first. As a user-friendly interface, it will detect the OS and run the progr am automatically for the detected OS. Please follow the following procedures to complete the setup. 1. When the OS is auto detected, the system will pop up the following window automatically. Click on "Next" to continue. 2.
ADSL Router AR-1150 User Manual 3. After filling in the Name and Company click on "Next" to continue. 4. Click on "O.K" to continue. 5. Select the Location of "C : / P r o g r a m F i l e s / A D S L R O U T E R " and click on "Next " to continue.
ADSL Router AR-1150 User Manual 6. Click on "Next" to add shortcut icons to the folder shown in the Window. 7. Click on "Install" to go on the install procedure. 8. Click "Finish" to complete the installation procedure.
ADSL Router AR-1150 User Manual Chapter 3 - Quick Guide for ADSL Router Configuration Tool For installation in Windows 98/98se/2000 It is essential to configure your ADSL Router before connecting it to the Internet. Please follow this quick guide for configuration under each individual encapsulation mode. After the software has been successfully installed, ADSL Router Configuration Utility can be opened from Start Manu->Program->ADSL ROUTER->ADSL EXE. 1.
ADSL Router AR-1150 User Manual 1. ADSL Bridge Modem Parameter Configuration 1.1 In Figure 1 In bridge mode, the ADSL Router provides 2 encapsulation methods, " B r i d g e d Ethernet Over ATM ( RFC 1483)" & "Bridged PPP over Ethernet". Figure 1.1 Figure1.2 1.2 In Figure 2 T o enter either of the protocols, a configuration window with " P V C S e t u p " , "TFTP/Telnet" and "ADSL Standard" tabs will display as the followings: 1. Enter the proper VPI, VCI numbers for connection. 2.
ADSL Router AR-1150 User Manual 1.3 In Figure 3 1. The Default mode for TFTP/Telnet is set in " Disable TFTP/Telnet." Note: Please refer to your Network Supervisor for the IP information if to enable "TFTP/Telnet" function. Figure 3 1.4 In Figure 4 1. The default ADSL Standard setting is "Multi Mode" Note: Please check with your Internet Service Provider for the actual setting. 2.
ADSL Router AR-1150 User Manual 2. ADSL Router Parameter Configuration In Router mode, the ADSL Router provides 5 encapsulation methods, " R o u t e d E t h e r n e t Over ATM (RFC 1483)", "Routed Classical Over ATM (RFC 1577)", "Routed PPP over ATM (RFC2364) " Routed PPP Over Ethernet (RFC2516) & "DHCP Server". 2.1 Routed Ethernet Over ATM (RFC1483) & Routed Classical Over ATM (RFC 1577) 2.1.1 In Figure 1 1.
ADSL Router AR-1150 User Manual 2.1.2 In Figure 2 1. The default mode for "ADSL Standard" set in "Multi Mode." Note: Please check your Internet Service Provider for the actual setting. Figure 2 2.1.3 In Figure 3 1. Enter the proper VPI, VCI numbers for connection. 2. Choose "LLC/SNNP" or "VCMUX" for connection. Note: The VPI and VCI will be provided by your Internet Service Provider.
ADSL Router AR-1150 User Manual 2.1.4 In Figure 4 1. Enter the Remote IP Address provided by your Internet Service Provider. 2.Click on "Config Modem" to activate the parameter settings. Figure 4 2.2 Routed PPP Over ATM (RFC2364) 2.2.
ADSL Router AR-1150 User Manual 2.2.2 In Figure 2 1. Please enter the " E t h e r n e t I P " and " N e t M a s k " addresses provided by your Internet Service Provider. N o t e : If the Internet Service Provider doesn't provide you the Ethernet IP, please click to enable "NAT" function. Figure 2 2.2.3 In Figure 3 1. The default mode for "ADSL Standard" is set in "Multi Mode." Note: Please check with your Internet Service Provider for the actual setting.
ADSL Router AR-1150 User Manual 2.2.4 In Figure 4 1. Enter the Proper VPI, VCI number for connection. 2. Select "LLC/SNAP" or "VCMUX" for the connection. Note: The VPI and VCI will be provided by your Internet Service Provider. Figure 4 2.2.5 In Figure 5 1. Enter the appropriate information for "Username" & "Password". 2. Select CHAP or PAP authentation 3. Click " Config Modem " the activate the parameter settings.
ADSL Router AR-1150 User Manual 3.PPP OVER ETHERNET(RFC2516) 3.1 In Figure 1 Note: P l e a s e e n t e r " C o n f i g P P P O E " f o r p a r a m e t e r s e t t i n g s f o r t h e f i r s t t i m e b e f o r e proceeding to "Enable PPPOA" or "Disable PPPOA". Figure 1 3.2 In Figure 2 Enter the " E t h e r n e t I P " & " N E T M a s k " IP addresses provided by your Internet provider.
ADSL Router AR-1150 User Manual 3.3 In Figure 3 The default mode for "ADSL Standard" set in "Multi-mode". Note: P l e a s e c h e ck w i t h y o u r I n t e r n e t S e r v i c e P r o v i d e r f o r t h e A c t u a l s e t t i n g s i f necessary. Figure 3 3.4 In Figure 4 1. Enter the Proper VPI, VCI number for connection. 2. Select "LLC/SNAP" or "VCMUX" for the connection. Note: The VPI and VCI will be provided by your Internet Service Provider. Figure 4 3.
ADSL Router AR-1150 User Manual 4. DHCP Server 4.1 In Figure 1 Note: For technical concerns, it requires password for "Config DHCP Server." Note: Please check with your network supervisor if you would like to set this function. Figure 1 4.2 In Figure 2 1. Enter the Password.( The default Password is "adsl") Figure 2 4.3 In Figure 3 1. Enter the appropriate Max. Lease Time.
ADSL Router AR-1150 User Manual 4.4 In Figure 4 1. Enter the appropriate IP addresses for " R a n g e 1 " , " R a n g e 2 " , " S u b n e t " , and "Netmask". Figure 4 4.5 In Figure 5 1. Enter the appropriate Gateway IP addresses. Figure 5 4.6 In Figure 6 1. Enter the appropriate IP addresses for " S u b n e t M a s k " , " B r o a d c a s t A d d r e s s ", and "DNS". 2. Click on "Config. Modem" to activate the parameter settings.
ADSL Router AR-1150 User Manual 5. Option for ADSL Router Configuration Tool 5.1 Command Line 5.1.1 Figure 1 1. It requires Password to enter the Command Line Configuration Window. Figure 1 5.1.2 Figure 2 1.Please enter the default password "adsl" to get into the Configuration Window.
ADSL Router AR-1150 User Manual 5.1.3 Figure 3 1. Enter the proper commands into the command line. Figure 3 5.2 Setup Password 5.2.1 Figure 1 1. If to change the password, please enter "Setup Password".
ADSL Router AR-1150 User Manual 5.2.2 Figure 2 1. Enter the default Old Password "adsl". 2. Enter the new password. 3. Re-enter the new Password for confirmation. Figure 2 5.3 Line Rate 5 .3.1 To check the current line rate, select " Line Rate" and an indicator as in Figure 2 will show the current line rate status.
ADSL Router AR-1150 User Manual 6 Reset all 6.1 Figure 1 & Figure 2 1. To re-set all the existing configurations, select "Reset all". Enter password "adsl" as show in Figure 2. Figure 1 Figure2 2. The indicator on the left will keep on running until the reset is totally completed.
ADSL Router AR-1150 User Manual About To get more information of the ADSL Configuration Utility, please select "About" to get the following window. Click on System Info [s] a dialogue box of Micro Soft System Data will appear. The system information of your computer will show the system information of your computer.
ADSL Router AR-1150 User Manual Copyright & Regulatory Information This manual and software described in it are copyrighted with all rights reserved. This manual may not be copied, in whole or in part, without written consent. All product names are trademarks and or registered trademarks of their respective companies. FCC Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
