Ubee TI D3.0 WLCM Model Number: DDW3600 User Manual Rev. 1.
◆ Important Safety Warnings "Installation" should include bonding the screen of the coaxial cable to the earth at the building entrance per ANSI/NFPA 70, the National Electrical Code (NEC), in particular Section 820.93, Grounding of Outer Conductive Shield of a Coaxial Cable. ◆ Installation Follow the procedures below to install the hardware. Figure 0 illustrates the connection relationship. 1.
4. CABLE Connector: This is where you connect the coaxial cable (not included) that leads to the cable splitter (not included) or the cable wall outlet. 5. USB: This is where you plug the USB cable. The other end connects to the USB port on the PC.
◆ LEDs on the front panel of the Modem Please see the LED descriptions below. LED Power Color Green DESCRIPTION Indicates that the cable modem has successfully completed internal power-on tests. LED flashes if power-on fails. DS Green/Orange Indicates that data is being received from the cable network. Orange indicates more than one Channel is bonded. Green indicates that one Channel is bonded. Prior to registration, DS would flash slowly to indicate it’s looking for DS channel.
LED must be solid once registered with network. WLAN Green Indicates connectivity in the WiFi port LED flashes when traffic is being passed. WPS Green TBD LAN1 to LAN4 Green/Orange Indicates connectivity between the Ethernet port on the cable modem and the PC’s Ethernet port. LED flashes when traffic is being passed. Green indicates GbE. Orange indicates that 10/100/1000 is enabled. USB Green Indicates connectivity in the USB port LED flashes when traffic is being passed.
Parameter US-DOCSIS 2.0 Downstream Output Value Center Frequency 91to 857 MHz (+/- 30 kHz) Level Range (one channel) -15 dBmV to +15 dBmV Modulation Type 64QAM, 256QAM and 1024QAM (Three Demodulators) Symbol Rate (nominal) 5.056941 Msym/s ( 64QAM) and 5.360537 Msym/s (256QAM) Bandwidth 6 MHz Total Input Power < 30 dBmV (40-900 MHz) Input Load Impedance 75 ohms Input Return Loss > 6 dB (88-860 MHz) Connector F connector DOCSIS 3.
Level Range (one channel) -15 dBmV to +15 dBmV Modulation Type 64QAM, 256QAM Symbol Rate (nominal) 5.056941 Msym/s ( 64QAM) and 5.360537 Msym/s (256QAM) Bandwidth 6 MHz (Alpha = 0.18 @ 64QAM & 0.12 @ 256QAM) Capture Bandwidth Supporting four channel bounding on continuous 64MHz CBW Total Input Power < 36 dBmV Input Load Impedance 75 ohms Input Return Loss > 6 dB (88-1002 MHz) Connector F connector WLAN RF Requirement Specification a) frequency rage： 2.412GHz to 2.
There are 7 channel at 802.11 b/g/ n model HT40 Channel Frequency FCC(USA) ID (MHz) 3 2422 O 4 2427 O 5 2432 O 6 2437 O 7 2442 O 8 2447 O 9 2452 O c）modulation： Standard Data Rate (Mbps) modul. coding DSSS-CCK 1 BPSK DSSS-CCK 2 QPSK DSSS-CCK 5.
MCS10 81 QPSK 3/4 MCS11 108 16QAM 1/2 MCS12 162 16QAM 3/4 MCS13 216 64QAM 2/3 MCS14 243 64QAM 3/4 MCS15 270 64QAM 5/6 Channels Rates Mbps Conditions 802.11g 1,6,11 6 @target power 20dBm 0&2 802.11g 1,6,11 36 @target power 20dBm 0&2 802.11g 1,6,11 48 @target power 19dBm 0&2 802.11b 1,6,11 @target power 19dBm 0&2 802.11n 1,6,11 MCS0/8 @target power 20dBm HT20/40 0&2 802.11n 1,6,11 MCS4/12 @target power 20dBm HT20/40 0&2 802.
Packet Error Rate (PER) 802.11g 802.11n 802.11n 1,6,11 @date rate=6,36,48,54 Mbps 1,6,11 @date rate=MCS0/8, MCS5/13, MCS6/14 & MCS7/15 1,6,11 PER<10% @date rate=MCS0/8, MCS5/13, MCS6/14 & MCS7/15 0&2 <10% HT20 0&2 <10% HT40 0&2 <10% 0&2 <-70dBm Receiver Sensitivity Test 802.11g 802.11n 802.
Section 820.93; Grounding of Outer Conductive Shield of a Coaxial Cable. 3. The device is also designed for IT power system with phase to phase voltage 120V. 4. How to disconnect device. The power plug shall be installed near the cable modem and shall be easily accessible. If abnormality happens to the cable modem, disconnect the power plug from the AC wall outlet immediately.
FCC Notice This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
