User's Manual

ManualsBrandsUbee Interactive ManualsElectronicsBCM 3383Z Wireless eMTA

Ubee Interactive — www.ubeeinteractive.com

1 Ubee DVW325 – Safety and Installation Product Insert v1.0

DVW325 Advanced Wireless Voice

Gateway - Safety and Installation

Product Insert

Federal Communications Commission

(FCC) Interference Statement

This device has been tested and found to comply

with the limits for a Class B digital device,

pursuant to Part 15 of the FCC Rules. These

limits are designed to provide reasonable

protection against harmful interference in a

residential installation. This device generates,

uses, and can radiate radio frequency energy. If

not installed and used in accordance with the

instructions, the device may cause harmful

interference to radio communications. There is

no guarantee, however, that interference will not

occur in a particular installation. If the DEVICE

causes harmful interference to radio or television

reception, which can be determined by turning it

off and on, the user can try to correct the

interference by one of the following measures:

 Increase the separation between the

DEVICE and the equipment with which it is

interfering (for example, a television or

radio).

 Connect the DEVICE into an electrical

outlet on a different circuit than the

interfered device is connected.

 Consult the dealer or an experienced

radio/TV technician for help.

FCC Regulatory Information

This device complies with Part 15 of the FCC

Rules. Operation is subject to the following two

conditions: (1) This device may not cause

harmful interference, and (2) this device must

accept any interference received, including

interference that may cause undesired operation.

There are two statements for this product:

 Only the type of Metal PIFA antenna tested

may be used.

Summary of content (7 pages)

PAGE 1
Ubee Interactive — www.ubeeinteractive.com DVW325 Advanced Wireless Voice Gateway - Safety and Installation Product Insert  Increase the separation between the DEVICE and the equipment with which it is interfering (for example, a television or radio).  Connect the DEVICE into an electrical outlet on a different circuit than the interfered device is connected.  Consult the dealer or an experienced radio/TV technician for help.
PAGE 2
Ubee Interactive — www.ubeeinteractive.com  The device must carry a label stating “FCC ID: XCNDVW325.” FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this device. IEEE 802.11b or 802.11g operation of this device in the U.S.A. is firmware-limited to channels 1 through 11. For operation within 5.15 ~ 5.25GHz frequency range, it is restricted to indoor environment.
PAGE 3
Ubee Interactive — www.ubeeinteractive.com 6. 7. 3 chemical cleaners. Avoid static discharge when touching the device by first touching the coaxial connector of the coaxial cable. Installation of the device should include grounding the coaxial cable to the earth at the building entrance per ANSI/NFPA 70 and the National Electrical Code (NEC, in particular, Section 820.93, Grounding of the Outer Conductive Shield of a Coaxial Cable).
PAGE 4
Ubee Interactive — www.ubeeinteractive.com 2. Connect one end of the supplied Ethernet cable to one of the ETHERNET ports (ETH1 to ETH4) on the device. Connect the other end to the ETHERNET port on a PC. Note: Category 5e or Category 6 Ethernet cables with RJ45 connectors must be used when connecting Ethernet devices to the LAN ports. This ensures Gigabit Ethernet speeds (unless the computer does not support it). 3.
PAGE 5
Ubee Interactive — www.ubeeinteractive.com 140mm (5.5 inches) Wall-Mount Installation You can mount the device on a wall using the 2 mounting brackets on the bottom of the device. We recommend that you use two round or pan head screws. 1. Install two screws horizontally apart on a wall using the measurement shown to the right. The screws should protrude from the wall so that you can fit the device between the head of the screw and the wall.
PAGE 6
Ubee Interactive — www.ubeeinteractive.com Additional Information 1. flash drives, etc. RESET Button (back of device): This button resets the device to factory defaults. Using a pointed object, insert it into the button opening, and hold for more than 10 seconds. The device will reset and reboot. Note: Not all parameters are reset to factory defaults. Refer to the User Guide for more information. 2.
PAGE 7
Ubee Interactive — www.ubeeinteractive.com US/DS—When the device initializes, the LED flashes. When the device locks on to channels and registers OK, the LED is On. When the device performs a firmware upgrade, the LED flashes. On-line—When the device is obtaining an IP address and configuration file, the LED flashes. When device obtains these items, the LED is On. from a wireless client that wishes to connect.