User's Manual

ManualsBrandsUbee Interactive ManualsComputers & AccessoriesWireless eMTA, Cable Modem

Ubee Interactive — www.ubeeinteractive.com

1 Ubee UBC1307-CA00 – Safety and Installation Product Insert v1.1

UBC1307-CA00 Advanced Wireless

Voice Gateway Safety and Installation

Product Insert

Federal Communications Commission

(FCC) Interference Statement

This device has been tested and found to comply

with the limits for a Class B digital device,

pursuant to Part 15 of the FCC Rules. These

limits are designed to provide reasonable

protection against harmful interference in a

residential installation. This device generates,

uses and can radiate radio frequency energy and,

if not installed and used in accordance with the

instructions, may cause harmful interference to

radio communications. However, there is no

guarantee that interference will not occur in a

particular installation. If this device does cause

harmful interference to radio or television

reception, which can be determined by turning

the equipment off and on, the user is encouraged

to try to correct the interference by one of the

following measures:

z Reorient or relocate the receiving antenna.

z Increase the separation between the

equipment and receiver.

z Connect the equipment into an outlet on a

circuit different from that to which the

receiver is connected.

z Consult the dealer or an experienced

radio/TV technician for help.

FCC Regulatory Information

This device complies with Part 15 of the FCC

Rules. Operation is subject to the following two

conditions: (1) This device may not cause

harmful interference, and (2) this device must

accept any interference received, including

interference that may cause undesired operation.

There is one statement for this product:

Summary of content (7 pages)

PAGE 1
Ubee Interactive — www.ubeeinteractive.com UBC1307-CA00 Advanced Wireless Voice Gateway Safety and Installation Product Insert Federal Communications Commission (FCC) Interference Statement This device has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
PAGE 2
Ubee Interactive — www.ubeeinteractive.com z The device must carry a label stating “FCC ID: XCNUBC1307.” FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this device. IEEE 802.11b or 802.11g operation of this device in the U.S.A. is firmware-limited to channels 1 through 11. Safety Notices Read these instructions carefully before operating the device.
PAGE 3
Ubee Interactive — www.ubeeinteractive.com the device by first touching the coaxial connector of the coaxial cable. 7. 3 Installation of the device should include grounding the coaxial cable to the earth at the building entrance per ANSI/NFPA 70 and the National Electrical Code (NEC, in particular, Section 820.93, Grounding of the Outer Conductive Shield of a Coaxial Cable). 8. The device is designed for IT power systems with phase-to-phase voltage at 100-240V. 9.
PAGE 4
Ubee Interactive — www.ubeeinteractive.com Installation 3. Connect one end of an RJ11 phone cable to one of the TEL ports (TEL1 to TEL2) on the device (a port that has been provisioned for voice service as specified by the service provider). Connect the other end to the phone port of the telephone. Note: If voice service is not provisioned through the service provider, telephone service is not available. 4. Connect the power adapter to the POWER port on the device.
PAGE 5
Ubee Interactive — www.ubeeinteractive.com Wall-Mount Installation You can mount the device on a wall using the 2 mounting brackets on the bottom of the device. We recommend that you use two round or pan head screws. 1. 2. Install two screws horizontally apart on a wall using the measurement shown to the right. The screws should protrude from the wall so that you can fit the device between the head of the screw and the wall.
PAGE 6
Ubee Interactive — www.ubeeinteractive.com Additional Information 1. 2. LED Indicators (Color = Green When On): RESET Button: To reset the device to factory defaults. Using a pointed object, insert it into the button opening, and hold for more than 10 seconds. The device will reset and reboot. Note: Not all parameters are reset to factory defaults. Refer to the User Guide for more information.
PAGE 7
Ubee Interactive — www.ubeeinteractive.com laptop, computer, etc. ETH—The Ethernet ports are used to connect Ethernet devices, such as computers, gaming consoles, and/or routers/hubs to the Device using RJ45 cables. Each Ethernet port has an LED to indicate their statuses when an Ethernet device is connected. When an Ethernet device, is connected to the cable modem, the LED is Green when connected at 10/100 Mbps speeds. The LED is Blue when connected at 1000 (Gigabit Ethernet) speed.