Before installation, please read this instructional guide completely and save for future reference. 1. Product Overview Installation Guide 1.1 View of UbiHub parts from top 1.2 View of UbiHub parts from bottom © 2021 Ubicquia Inc. | All rights reserved. Patent pending. Public use approved.
1.3 Package Contents • UbiHub Unit (with open cap attached) • Mounting Clamp • Mounting Clamp Inserts (additional) • Dual-Camera • Grounding Cable 1.4 Required Tools (Not Included) • 3/16” Hex bit driver / Wrench • Standard Screwdriver or 5/16” Socket for grounding screw • Deep drive ½” Socket 3. Preinstall Clamp 3.1 Measure and Preinstall Clamp The clamp fits a 2.3/8” (60.3 mm) diameter pole, with optional replacement inserts to accommodate for a smaller pole diameter, and can be adjusted between 6.
.4 Use a 3/16” Hex bit driver to unscrew and remove the clamp adjustment cover from the clamp. Discard as this piece is no longer needed. 3.5 Align the shuttles on the top of the clamp with the rail openings on the bottom of the UbiHub housing while still in the box. There is a single orientation for assembly. 3.3 OPTIONAL: Measure the distance from the NEMA socket to the closest point on the pole that will allow for the Ubihub to be seated level to the luminaire. 3.
3.7 Open the clamp with the swivel locking nut up out of the way. If your pole arm is smaller than 2.3/8” (60.3 mm), you will install a clamp insert set into the clamp. Clamp inserts are available in 1.25” sizes, and come as a set of two. The inserts are clearly marked with a numeral 1 or 2, denoting the top clamp insert from the bottom clamp insert. The inserts should be placed into the corresponding location in the clamp, ensuring a complete fit. They should not be loose after install.
. Mounting the Unit 5.1 Remove the UbiHub from the shipping box by first gently lifting the unit with the attached camera placed on top. The camera is shipped pre-installed and connected to the unit by a cable. Caution: Take care not to swing, slam, or knock the camera during installation. The camera should be placed atop the unit during install, whenever possible. Make sure clamp is open with the swivel locking nut up out of the way before installing on the luminaire. 5.
A. Use a screwdriver to remove the two screws. Unscrew the NEMA connector and lift then turn the NEMA connector until the N > is facing in the correct direction (away from the luminaire pole). 6.4 Once plugged, rotate the UbiHub towards the pole to lock the NEMA connecter in place. Stop once the clamp is aligned with the pole. B. Pull the inside (grey) section of the NEMA connector out slightly and twist until the N > is facing in the correct direction (away from the luminaire pole). 6.
6.7 A. Once unit is leveled, tighten the vertical adjustment screws to 40 in-lbs torque using the 3/16” Hex bit driver. B. Then tighten the horizontal adjustment screws to 40 in-lbs torque using the 3/16” Hex bit driver. 6.8 Remove tether from unit. NOTE: Remove all protective packaging material from the camera prior to installation. 6.10 Tighten the camera top screw to 15 in-lbs torque using the 3/16” Hex bit driver. 7. Grounding Cable Installation 7.
If installing a lighting controller, follow steps 8.1 and 8.2. 8. Installing Photocell (Optional) 8.3 Installation of the UbiHub is now complete. Make sure UbiHub and all elements are connected and secured firmly in place. 8.1 Remove the open cap by twisting counterclockwise and pull out. 8.2 Insert the photocell into the NEMA connector on the top of the UbiHub and twist clockwise until locked in place.
Support and Technical Specifications: FCC statement Model AP6: UBH-H-WI Model APAI: UBH-H-AI FCCID: 2AECKUBH01 Contains FCCID: XMR201903EG25G LTE Module Options supported Contains FCCID: XMR201807EP06A This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1) This device may not cause harmful interference, and 2) This device must accept any interference received, including interference that may cause undesired operation.
Safety Statements and Warnings This product has been ETL listed and complies with U.S. product safety standards. WARNING statements describe conditions that may lead to personnel injury including potentially fatal injuries if the device is not properly installed and warnings are not properly followed. CAUTION statements describe conditions that may lead to equipment damage. • Electrical shock can cause serious or fatal injury. Only qualified personnel should install, maintain or troubleshoot this equipment.
