5 GHz, 23 dBi Slant 45 Antenna for airFiber® Model: AF-5G23-S45
Introduction Thank you for purchasing the Ubiquiti Networks® airFiber® X Antenna. This Quick Start Guide is designed to guide you through installation and includes the warranty terms. Package Contents airFiber X Antenna Clamp Bracket Protective Shroud U-Bolt Mount Bracket Cable Tie 5 GHz, 23 dBi Slant 45 Antenna for airFiber® Model: AF-5G23-S45 Hex Bolts with Washer Set (M8x20, Qty. 4) Flange Nuts (M8, Qty. 2) Hex Nuts (M8, Qty.
Installation Requirements • 5 GHz airFiber X radio (sold separately) • 13 mm wrench Other Requirements • • • • Clear line of sight between airFiber radios Clear view of the sky for proper GPS operation Vertical mounting orientation Mounting point: • At least 1 m below the highest point on the structure • For tower installations, at least 3 m below the top of the tower • Ground wires – min. 10 AWG (5 mm2) and max. length: 1 m.
Installation Important: Handle the airFiber X Antenna with care. Deformations in its reflector may reduce the antenna's effectiveness. 1. Attach the airFiber X radio to the antenna by aligning the four tabs on the back of the radio with the slots of the radio mount. Then slide the radio down to lock it into place.
2. Attach the RF connectors to the radio in this combination: +45° to Chain 0 and -45° to Chain 1. Then slide the jackets over the RF connectors to protect them. 3. Attach the external GPS antenna (included with the radio) to the RF connector labeled GPS on the radio.
4. Attach the Protective Shroud by sliding it down over the radio until it locks into the radio mount. 5. Insert the U-Bolt through the slots of the Mount Bracket.
6. Fasten the U-Bolt to the Mount Bracket with the Cable Tie. 7. Secure the Mount Bracket to the antenna using the four Hex Bolts with Washer Set.
. Position the antenna at the desired location on the pole and secure it: a. Slide the Clamp Bracket over the U-Bolt. b. Fasten one Flange Nut on each end of the U-Bolt. Note: The mounting assembly can accommodate a Ø 38 - 64 mm pole.
Aligning the Antenna Optimize the airFiber link by adjusting one end of the link at a time. Refer to the airFiber X radio Quick Start Guide for additional details. 1. Adjust the azimuth and aim the antenna toward the other end of the link: a. Loosen the two Flange Nuts on the U-Bolt. b. Rotate the antenna to point towards the other end of the link. c. Tighten the two Flange Nuts.
2. The elevation angle may be adjusted ±15°. Adjust the elevation angle: a. Loosen the four Hex Bolts on both sides of the antenna. b. Pivot the antenna to the desired elevation. c. Tighten the four Hex Bolts. 3. Repeat steps 1 and 2 as needed to optimize the link.
4. Once the link is optimized, lock the aim: a. Tighten all bolts and nuts to approximately 25 N-m. b. Fasten the two Hex Nuts to the U-Bolt to prevent the Flange Nuts from loosening.
Specifications AF-5G23-S45 Dimensions 378 x 378 x 290 mm (14.88 x 14.88 x 11.42") Weight 3.4 kg (7.5 lb) (Mount Included) Frequency 5.1 - 5.9 GHz Gain 23 dBi Max. VSWR 1.5:1 Wind Survivability Wind Loading 200 km/h (125 mph) 190 N @ 200 km/h (43 lbf @ 125 mph) Polarization Dual Linear F/B Ratio 33 dB ETSI Specification Mounting EN 302 326 DN2 Universal Pole Mount for Ø 38 - 64 mm (Ø 1.5 - 2.5") Poles Safety Notices 1. Read, follow, and keep these instructions. 2. Heed all warnings. 3.
Limited Warranty UBIQUITI NETWORKS, Inc (“UBIQUITI NETWORKS”) warrants that the product(s) furnished hereunder (the “Product(s)”) shall be free from defects in material and workmanship for a period of one (1) year from the date of shipment by UBIQUITI NETWORKS under normal use and operation.
Returns No Products will be accepted for replacement or repair without obtaining a Return Materials Authorization (RMA) number from UBIQUITI NETWORKS during the warranty period, and the Products being received at UBIQUITI NETWORKS’ facility freight prepaid in accordance with the RMA process of UBIQUITI NETWORKS. Products returned without an RMA number will not be processed and will be returned freight collect or subject to disposal.
Limitation of Liability EXCEPT TO THE EXTENT PROHIBITED BY LOCAL LAW, IN NO EVENT WILL UBIQUITI OR ITS SUBSIDIARIES, AFFILIATES OR SUPPLIERS BE LIABLE FOR DIRECT, SPECIAL, INCIDENTAL, CONSEQUENTIAL OR OTHER DAMAGES (INCLUDING LOST PROFIT, LOST DATA, OR DOWNTIME COSTS), ARISING OUT OF THE USE, INABILITY TO USE, OR THE RESULTS OF USE OF THE PRODUCT, WHETHER BASED IN WARRANTY, CONTRACT, TORT OR OTHER LEGAL THEORY, AND WHETHER OR NOT ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
RoHS/WEEE Compliance Statement English European Directive 2002/96/EC requires that the equipment bearing this symbol on the product and/or its packaging must not be disposed of with unsorted municipal waste. The symbol indicates that this product should be disposed of separately from regular household waste streams. It is your responsibility to dispose of this and other electric and electronic equipment via designated collection facilities appointed by the government or local authorities.
Español La Directiva 2002/96/CE de la UE exige que los equipos que lleven este símbolo en el propio aparato y/o en su embalaje no deben eliminarse junto con otros residuos urbanos no seleccionados. El símbolo indica que el producto en cuestión debe separarse de los residuos domésticos convencionales con vistas a su eliminación.
Declaration of Conformity Česky [Czech] UBIQUITI NETWORKS tímto prohlašuje, že toto UBIQUITI NETWORKS zařízení, je ve shod se základními požadavky a dalšími příslušnými ustanoveními směrnice 1999/5/ES. Dansk [Danish] Hermed, UBIQUITI NETWORKS, erklærer at denne UBIQUITI NETWORKS enhed, er i overensstemmelse med de væsentlige krav og øvrige relevante krav i direktiv 1999/5/EF.
Latviski [Latvian] Ar šo, UBIQUITI NETWORKS, deklarē, ka UBIQUITI NETWORKS ierīce, ir saskaņā ar būtiskajām prasībām un citiem attiecīgiem noteikumiem Direktīvā 1999/5/EK. Lietuviškai [Lithuanian] UBIQUITI NETWORKS deklaruoja, kad šis UBIQUITI NETWORKS įrenginys atitinka esminius reikalavimus ir kitas 1999/5/EB Direktyvos nuostatas.
www.ubnt.com ©2015 Ubiquiti Networks, Inc. All rights reserved. Ubiquiti, Ubiquiti Networks, the Ubiquiti U logo, the Ubiquiti beam logo, airFiber, and TOUGHCable are trademarks or registered trademarks of Ubiquiti Networks, Inc. in the United States and in other countries. All other trademarks are the property of their respective owners.
