Indoor Access Point with External Antenna Model: airGateway-LR
Introduction Thank you for purchasing the Ubiquiti Networks™ airGateway™. This Quick Start Guide is designed to guide you through the installation, and show you how to access the airOS® Configuration Interface. This Quick Start Guide also includes the warranty terms and is for use with the airGateway LR. Package Contents POE LAN airGateway LR External Antenna Wall Mount Bracket Screws (M2.9x20, Qty. 2) Screw Anchors (M2.9x20, Qty.
Hardware Overview Top RJ45 Connector (Male) LED Antenna Connector POE PoE Port LAN LAN Port LED Steady White Indicates bootup/initializition/power-on. Steady Blue Indicates the airGateway is working properly and an active connection is detected. Alternating Blue/White Indicates the device is busy; do not move or unplug.
Bottom Reset Ext Reset Mounting Tabs Reset Resets the airGateway to factory defaults. To reset the airGateway, press and hold the Reset button for more than five seconds while the airGateway is powered on. Reset Ext Resets the airMAX® CPE device connected to the airGateway to factory defaults. To reset the airMAX device, press and hold the Reset Ext button for more than five seconds while the airMAX device is powered on.
Installation Requirements The airGateway is powered by and integrates exclusively with Ubiquiti Networks PoE adapters. A wall mount kit is included. • • • • • Ubiquiti Networks PoE Adapter (24V, 0.5A) Ubiquiti Networks airMAX CPE device CAT5/6 cable 6 mm drill bit and drill Screwdriver Hardware Installation WARNING: Do not connect non‑PoE devices (such as laptops) to the POE port. To install the airGateway, perform the following steps: 1.
2. Insert the male RJ45 Connector of the airGateway into the Ethernet port labeled POE on the PoE Adapter. Push the two units together until they connect. PO E LA N PO E LA N 3. Connect the Ethernet cable that was disconnected from the POE port in step 1 to the POE port on the airGateway.
4. Connect the Ethernet cable that was disconnected from the LAN port in step 1 to the LAN port on the airGateway. PO E LA N PO E LA N 5. Connect the External Antenna to the Antenna Connector on the airGateway.
Wall Mounting 1. Position the Wall Mount Bracket at the desired location on the wall with the bubble level at the bottom. Use the bubble level to ensure the bracket is plumb. 2. Mark the two holes with a pencil.
3. Drill the holes in the wall using a 6 mm drill bit. 4. Insert a Screw Anchor into each hole. Secure the Wall Mount Bracket to the wall by inserting a Screw into each Screw Anchor.
5. Attach the airGateway and PoE Adapter assembly to the Wall Mount Bracket: a. Insert the two Mounting Tabs on the airGateway into the slots located at the top of the Wall Mount Bracket. b. Rotate the PoE Adapter into the Wall Mount Bracket until it snaps in place.
Connecting via Wi-Fi To configure the airGateway, you must access it via Wi‑Fi from a computer. 1. Connect to the wireless network (SSID) named www.ubnt.com. 2. Launch your web browser and type https://192.168.1.1 in the address field. Press enter (PC) or return (Mac). Note: Your computer needs to be on the 192.168.1.x subnet. If you have DHCP enabled on your Ethernet adapter, it should receive an address automatically. If not, you will need to set a static IP address in the 192.168.1.2 - 192.168.1.
4. Change the default airGateway administrator password. Enter a new password in the New Password and Verify Password fields and click Next. 5. Enter a name for your wireless network (SSID) and a password (passphrase) for your wireless network. Click Next.
6. Verify your settings and click Finish or click Previous to change the settings. The airGateway is ready to use. Connect wireless clients as described below: Windows 1. Go to Connect to Network. -- Windows 8 Click the Network icon. -- Windows 7 Right-click the Network icon. -- Windows Vista Go to Start > Connect To. -- Windows XP Right-click the Wireless Network icon in the System Tray (lower right corner of the screen). Click View Available Wireless Networks. 2.
Specifications airGateway-LR Dimensions Weight Networking Interface Buttons Enclosure Frequency Antenna Wi-Fi Standards Wireless Security Max. TX Power Max. Power Consumption Power Supply Power Method Certifications Mounting Operating Temperature Operating Humidity airGateway: 54 x 44 x 30 mm Mount: 154 x 49 x 39 mm 83 g (with mount) (2) 10/100 Ethernet Ports (1) Reset airGateway (1) Reset External airMAX Device Polycarbonate 2.412 - 2.484 GHz (1) External 5 dBi 802.11 b/g/n (2.
Safety Notices 1. Read, follow, and keep these instructions. 2. Heed all warnings. 3. Only use attachments/accessories specified by the manufacturer. WARNING: Do not use this product in location that can be submerged by water. WARNING: Avoid using this product during an electrical storm. There may be a remote risk of electric shock from lightning. Electrical Safety Information 1.
Limited Warranty UBIQUITI NETWORKS, Inc (“UBIQUITI NETWORKS”) warrants that the product(s) furnished hereunder (the “Product(s)”) shall be free from defects in material and workmanship for a period of one (1) year from the date of shipment by UBIQUITI NETWORKS under normal use and operation.
Disclaimer EXCEPT FOR ANY EXPRESS WARRANTIES PROVIDED HEREIN, UBIQUITI NETWORKS, ITS AFFILIATES, AND ITS AND THEIR THIRD PARTY DATA, SERVICE, SOFTWARE AND HARDWARE PROVIDERS HEREBY DISCLAIM AND MAKE NO OTHER REPRESENTATION OR WARRANTY OF ANY KIND, EXPRESS, IMPLIED OR STATUTORY, INCLUDING, BUT NOT LIMITED TO, REPRESENTATIONS, GUARANTEES, OR WARRANTIES OF MERCHANTABILITY, ACCURACY, QUALITY OF SERVICE OR RESULTS, AVAILABILITY, SATISFACTORY QUALITY, LACK OF VIRUSES, QUIET ENJOYMENT, FITNESS FOR A PARTICULAR PUR
Note Some countries, states and provinces do not allow exclusions of implied warranties or conditions, so the above exclusion may not apply to you. You may have other rights that vary from country to country, state to state, or province to province. Some countries, states and provinces do not allow the exclusion or limitation of liability for incidental or consequential damages, so the above limitation may not apply to you.
Industry Canada This Class A digital apparatus complies with Canadian ICES-003. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that permitted for successful communication. This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: 1. This device may not cause interference, and 2.
Australia and New Zealand Warning: This is a Class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures. CE Marking CE marking on this product represents the product is in compliance with all directives that are applicable to it.
Español La Directiva 2002/96/CE de la UE exige que los equipos que lleven este símbolo en el propio aparato y/o en su embalaje no deben eliminarse junto con otros residuos urbanos no seleccionados. El símbolo indica que el producto en cuestión debe separarse de los residuos domésticos convencionales con vistas a su eliminación.
Declaration of Conformity Česky [Czech] UBIQUITI NETWORKS tímto prohla uje, e tento UBIQUITI NETWORKS device, je ve shod se základními po adavky a dal ími p íslu n mi ustanoveními sm rnice 1999/5/ES. Dansk [Danish] Undertegnede UBIQUITI NETWORKS erklærer herved, at følgende udstyr UBIQUITI NETWORKS device, overholder de væsentlige krav og øvrige relevante krav i direktiv 1999/5/EF.
Italiano [Italian] Con la presente UBIQUITI NETWORKS dichiara che questo UBIQUITI NETWORKS device, è conforme ai requisiti essenziali ed alle altre disposizioni pertinenti stabilite dalla direttiva 1999/5/CE. Latviski [Latvian] Ar o UBIQUITI NETWORKS deklar , ka UBIQUITI NETWORKS device, atbilst Direkt vas 1999/5/EK b tiskaj m pras b m un citiem ar to saist tajiem noteikumiem.
www.ubnt.com ©2013 Ubiquiti Networks, Inc. All rights reserved. airGateway™, airMAX®, Ubiquiti Networks™, and the Ubiquiti logo® are trademarks or registered trademarks of Ubiquiti Networks, Inc. in the United States and in other countries.
