Zero-Variable Outdoor Radio Models: BM2-Ti, BM5-Ti
Introduction Introduction Thank you for purchasing the Bullet™ M Titanium. This Quick Start Guide is designed to guide you through the installation of the Bullet M Titanium and show you how to access the configuration interface.
Bullet™ M Titanium Quick Start Guide Hardware Overview N-Type Female Connector Bullet™ M Titanium Radio Rubber Washer Ethernet Port Cable Gland Body Compression Seal Compression Nut 2
Hardware Installation Hardware Installation To install the Bullet M Titanium, perform the following steps: 1. Unscrew the Cable Gland Body and detach it from the Bullet M Titanium Radio. 2. Unscrew the Compression Nut and remove the Compression Seal from the Cable Gland Body.
Bullet™ M Titanium Quick Start Guide 3. Slide the Compression Nut over the Ethernet cable with the threaded end facing the RJ-45 connector. Slip the Compression Seal around the cable. 4. Feed the Ethernet cable through the Cable Gland Body and seat the Compression Seal into the Cable Gland Body. 5. Connect the Ethernet cable to the port located on the bottom of the Bullet M Titanium Radio.
Hardware Installation 6. Securely screw the Cable Gland Body into the Bullet M Titanium. Tightly screw the cable gland so that the Rubber Washer seals the bottom of the Bullet M Titanium. 7. Tightly screw on the Compression Nut. Ensure the rubber is securely compressed and tightly sealed around the cable.
Bullet™ M Titanium Quick Start Guide 8. Connect the Bullet M Titanium to the antenna. Note: The Bullet M Titanium should be mounted vertically to reduce stress on the N-Type Connector. The N-Type Right Angle Adapter may be used as needed. 9. Connect the other end of the Ethernet cable from the Bullet M Titanium to the Ethernet port labeled POE on the PoE Adapter.
Hardware Installation 10. Connect an Ethernet cable from your LAN to the Ethernet port labeled LAN on the PoE Adapter. 11. Connect the power cord to the power port on the PoE Adapter. Connect the other end of the power cord to a power outlet. The hardware installation of your Bullet M Titanium is complete. Continue to the next section "Accessing the airOS Utility" to configure the Bullet M Titanium.
Bullet™ M Titanium Quick Start Guide Accessing the airOS Utility 1. Make sure that your host machine is connected to the LAN that is connected to the Bullet™ M Titanium. 2. Configure the Ethernet adapter on your host system with a static IP address on the 192.168.1.x subnet (e.g., 192.168.1.100). 3. Launch your Web browser. Type http://192.168.1.20 in the address field and press enter (PC) or return (Mac). 4. The login screen will appear. Enter ubnt in the Username and Password fields.
Specifications Specifications Bullet™ M Titanium Specifications Dimensions 190 mm x 46 mm Weight 196 g Max. Power Consumption M2 7 Watts M5 6 Watts Power Supply Power Method 24V, 1A PoE Supply Included Passive PoE (Pairs 4, 5+; 7,8 return) Certifications CE, FCC, IC Operating Temperature -40 to +80° C Operating Frequency M2 2402 - 2462 MHz M5 5170 - 5875 MHz* Networking Interface (1) 10/100 Ethernet Port * Only 5725 - 5850 MHz supported in the USA Safety Notices 1.
Bullet™ M Titanium Quick Start Guide Electrical Safety Information 1. Compliance is required with respect to voltage, frequency, and current requirements indicated on the manufacturer’s label. Connection to a different power source than those specified may result in improper operation, damage to the equipment or pose a fire hazard if the limitations are not followed. 2. There are no operator serviceable parts inside this equipment. Service should be provided only by a qualified service technician. 3.
General Warranty warranties, express or implied, including the implied warranties of merchantability and fitness for a particular purpose and any warranties arising from a course of dealing, usage or trade practice with respect to the products. Repair or replacement in the manner provided herein shall be the sole and exclusive remedy of Buyer for breach of warranty and shall constitute fulfillment of all liabilities of UBIQUITI NETWORKS with respect to the quality and performance of the Products.
Bullet™ M Titanium Quick Start Guide selection of products for buyer’s application and/or failure of products to meet government or regulatory requirements. Returns In the unlikely event a defect occurs, please work through the dealer or distributor from which this product was purchased. Compliance FCC Changes or modifications not expressly approved by Ubiquiti Networks, Inc. could void the user’s authority to operate the equipment. This device complies with Part 15 of the FCC Rules.
Compliance L'émetteur-récepteur décrit ici émet de l'énergie de fréquence radio. Bien que le niveau de puissance est faible, l'énergie concentrée à partir d'une antenne directionnelle peut présenter un danger pour la santé. Ne pas permettre aux gens de se rapprocher de 157 cm à l'antenne lorsque l'émetteur est en marche. Des renseignements supplémentaires sur l'exposition aux RF est disponible sur Internet à www.fcc.
Bullet™ M Titanium Quick Start Guide Declaration of Conformity Česky [Czech] UBIQUITI NETWORKS tímto prohla uje, e tento UBIQUITI NETWORKS device, je ve shod se základními po adavky a dal ími p íslu n mi ustanoveními sm rnice 1999/5/ES. Dansk [Danish] Undertegnede UBIQUITI NETWORKS erklærer herved, at følgende udstyr UBIQUITI NETWORKS device, overholder de væsentlige krav og øvrige relevante krav i direktiv 1999/5/EF.
Declaration of Conformity Latviski [Latvian] Ar o UBIQUITI NETWORKS deklar , ka UBIQUITI NETWORKS device, atbilst Direkt vas 1999/5/EK b tiskaj m pras b m un citiem ar to saist tajiem noteikumiem. Lietuviškai [Lithuanian] UBIQUITI NETWORKS deklaruoja, kad šis UBIQUITI NETWORKS įrenginys atitinka esminius reikalavimus ir kitas 1999/5/EB Direktyvos nuostatas.
English We recommend that you protect your networks from the most brutal environments and devastating ESD attacks with industrial‑grade shielded Ethernet cable from Ubiquiti Networks. For more details, visit www.ubnt.com/toughcable Deutsch Schützen Sie Ihre Netzwerke vor extremen Umwelteinflüssen und verheerender elektrostatischer Entladung (ESD), indem Sie abgeschirmte Ethernetkabel in Unternehmensqualität von Ubiquiti Networks verwenden. Weitere Informationen erhalten Sie unter www.ubnt.
Ubiquiti Networks Support Email: support@ubnt.com Phone (9 a.m. - 5 p.m. PST): 408-942-1153 Online Resources Wiki Page: www.ubnt.com/wiki Support Forum: www.ubnt.com/forum Downloads: www.ubnt.com/support/downloads www.ubnt.com © 2011 Ubiquiti Networks, Inc. All rights reserved.
