5 GHz High-Performance Model: M5GHP
Introduction Introduction Thank you for purchasing the Ubiquiti Networks™ airGrid™ 5 GHz High-Performance Integrated InnerFeed Antenna, model AGM5-HP-1724. This Quick Start Guide is designed to guide you through the installation, and show you how to access the airOS™ Configuration Interface. Package Contents Antenna Feed Rear Housing Feed Extender L-Bracket Grid Reflector Pole Clamp M8 U-Bolt 5 GHz High-Performance Integrated InnerFeed Antenna Model: AGM5-HP-1724 M8 Flange Nuts (Qty.
airGrid™ AGM5-HP-1724 Quick Start Guide Installation Requirements • 13 mm or ½" wrench • Shielded Category 5 (or above) cabling should be used for all wired Ethernet connections and should be grounded through the AC ground of the PoE. We recommend that you protect your networks from the most brutal environments and devastating ESD attacks with industrial‑grade shielded Ethernet cable from Ubiquiti Networks. For more details, visit www.ubnt.
LEDs LEDs Signal In airOS, you can modify the wireless signal strength threshold values for each LED on the Advanced tab under Signal LED Thresholds. The default values are shown below: LED will light green when the wireless signal strength is above -65 dBm. LED will light green when the wireless signal strength is above -73 dBm. LED will light amber when the wireless signal strength is above -80 dBm. LED will light red when the wireless signal strength is above -94 dBm.
airGrid™ AGM5-HP-1724 Quick Start Guide Hardware Installation Assemble the airGrid according to your chosen polarization. 1. Attach the L-Bracket to the Grid Reflector by sliding the tabs into the slots. Vertical Polarization Horizontal Polarization WARNING: The polarization of the airGrid must match the polarization of its corresponding device (horizontal to horizontal, vertical to vertical). 2.
Hardware Installation 3. Attach the Rear Housing: a. Ensure the four alignment holes on the Grid Reflector and L-Bracket are lined up. b. Orient the Rear Housing with the locking tab of the cable feed door facing up. c. Insert the alignments pins of the Rear Housing into the alignment holes, and push until the Rear Housing locks into place with a click. Vertical Polarization Horizontal Polarization 4. Insert the Feed Extender into the Rear Housing with the Release Button facing down.
airGrid™ AGM5-HP-1724 Quick Start Guide 5. Lift the locking tab of the cable feed door and detach the door from the Rear Housing. 6. Route an Ethernet cable through the Rear Housing and Feed Extender. Connect the cable to the Ethernet port on the back of the Antenna Feed.
Hardware Installation 7. Attach the Antenna Feed: a. Rotate the Antenna Feed to match the signal polarization. b. Insert the Antenna Feed into the Feed Extender, and push until it locks into place with a click. Vertical Polarization Horizontal Polarization 8. Lightly pull the Antenna Feed to ensure that the Release Button is fully engaged and locked into place.
airGrid™ AGM5-HP-1724 Quick Start Guide 9. The Release Button indicates the Antenna Feed polarization. Confirm that the Antenna Feed polarization matches the Grid Reflector polarization shown in step 2. Vertical Polarization Horizontal Polarization Note: If you need to remove the Antenna Feed, you must depress the Release Button first. 10. Re-attach the cable feed door to the Rear Housing. Ensure the locking tab securely latches to the Rear Housing.
Hardware Installation 11. Slide the Pole Clamp onto the L-Bracket. 12. Insert the M8 U-Bolt into the Pole Clamp and L-Bracket. Secure each end of the M8 U-Bolt with a M8 Flange Nut. 9 N-m (80 lb-in) Note: The mounting assembly can accommodate a Ø 1.25" - 2.2" pole.
airGrid™ AGM5-HP-1724 Quick Start Guide Connecting Power over Ethernet 1. Connect the other end of the Ethernet cable from the airGrid to the Ethernet port labeled POE on the PoE Adapter. 2. Connect an Ethernet cable from your LAN to the Ethernet port labeled LAN on the PoE Adapter. 3. Connect the Power Cord to the power port on the PoE Adapter. Connect the other end of the Power Cord to a power outlet.
airOS Configuration airOS Configuration Verify connectivity in the airOS Configuration Interface and select the airGrid antenna size. 1. Make sure that your host machine is connected via Ethernet to the airGrid. 2. Configure the Ethernet adapter on your host system with a static IP address on the 192.168.1.x subnet. 3. Launch your web browser and type https://192.168.1.20 in the address field. Press enter (PC) or return (Mac). 4. The login screen will appear.
airGrid™ AGM5-HP-1724 Quick Start Guide 5. Select the airGrid antenna size: a. Click the Wireless tab. b. From the Antenna drop-down list, select the appropriate option. c. Click Change to save. d. Click OK to confirm. Customize additional settings as needed to complete the installation. Please review the Installer Compliance Responsibility section on the following page. For additional details on the airOS Configuration Interface, refer to the User Guide available at documentation.ubnt.
Installer Compliance Responsibility Installer Compliance Responsibility Devices must be professionally installed and it is the professional installer's responsibility to make sure the device is operated within local country regulatory requirements. Since Ubiquiti Networks equipment can be paired with a variety of antennas and cables, the Antenna and Output Power fields are provided to the professional installer to assist in meeting regulatory requirements.
airGrid™ AGM5-HP-1724 Quick Start Guide Specifications AGM5-HP-1724 Dimensions Weight Networking Interface 620 x 460 x 360 mm (Mount Included) 2585 g (Mount Included) (1) 10/100 Ethernet Port Enclosure Outdoor UV Stabilized Plastic Frequency Worldwide: 5170 – 5875 MHz USA: 5725 – 5825 MHz Gain Max. Power Consumption Power Supply Power Method Max. VSWR Wind Survivability 28 dBi 3.0 W 24V, 0.5A PoE Adapter (Included) Passive Power over Ethernet (Pairs 4, 5+; 7, 8 Return) 1.
Safety Notices Safety Notices 1. Read, follow, and keep these instructions. 2. Heed all warnings. 3. Only use attachments/accessories specified by the manufacturer. WARNING: Do not use this product in location that can be submerged by water. WARNING: Avoid using this product during an electrical storm. There may be a remote risk of electric shock from lightning. Electrical Safety Information 1.
airGrid™ AGM5-HP-1724 Quick Start Guide General Warranty UBIQUITI NETWORKS, Inc (“UBIQUITI NETWORKS”) represents and warrants that the Products furnished hereunder shall be free from defects in material and workmanship for a period of one (1) year from the date of shipment by UBIQUITI NETWORKS under normal use and operation. UBIQUITI NETWORKS sole and exclusive obligation under the foregoing warranty shall be to repair or replace, at its option, any defective Product that fails during the warranty period.
General Warranty Warranty Conditions The foregoing warranty shall apply only if: (I) The Product has not been subjected to misuse, neglect or unusual physical, electrical or electromagnetic stress, or some other type of accident. (II) No modification, alteration or addition has been made to the Product by persons other than UBIQUITI NETWORKS or UBIQUITI NETWORK’S authorized representatives or otherwise approved by UBIQUITI NETWORKS.
airGrid™ AGM5-HP-1724 Quick Start Guide Compliance FCC This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user‘s authority to operate the equipment.
Compliance Cet appareil est conforme à la norme RSS Industrie Canada exempts de licence norme(s). Son fonctionnement est soumis aux deux conditions suivantes: 1. Cet appareil ne peut pas provoquer d’interférences et 2. Cet appareil doit accepter toute interférence, y compris les interférences qui peuvent causer un mauvais fonctionnement du dispositif.
airGrid™ AGM5-HP-1724 Quick Start Guide RoHS/WEEE Compliance Statement English European Directive 2002/96/EC requires that the equipment bearing this symbol on the product and/or its packaging must not be disposed of with unsorted municipal waste. The symbol indicates that this product should be disposed of separately from regular household waste streams.
Compliance Français La directive européenne 2002/96/CE exige que l’équipement sur lequel est apposé ce symbole sur le produit et/ou son emballage ne soit pas jeté avec les autres ordures ménagères. Ce symbole indique que le produit doit être éliminé dans un circuit distinct de celui pour les déchets des ménages.
airGrid™ AGM5-HP-1724 Quick Start Guide Declaration of Conformity Česky [Czech] UBIQUITI NETWORKS tímto prohla uje, e tento UBIQUITI NETWORKS device, je ve shod se základními po adavky a dal ími p íslu n mi ustanoveními sm rnice 1999/5/ES. Dansk [Danish] Undertegnede UBIQUITI NETWORKS erklærer herved, at følgende udstyr UBIQUITI NETWORKS device, overholder de væsentlige krav og øvrige relevante krav i direktiv 1999/5/EF.
Declaration of Conformity Latviski [Latvian] Ar o UBIQUITI NETWORKS deklar , ka UBIQUITI NETWORKS device, atbilst Direkt vas 1999/5/EK b tiskaj m pras b m un citiem ar to saist tajiem noteikumiem. Lietuviškai [Lithuanian] UBIQUITI NETWORKS deklaruoja, kad šis UBIQUITI NETWORKS įrenginys atitinka esminius reikalavimus ir kitas 1999/5/EB Direktyvos nuostatas.
English We recommend that you protect your networks from the most brutal environments and devastating ESD attacks with industrial‑grade shielded Ethernet cable from Ubiquiti Networks. For more details, visit www.ubnt.com/toughcable Deutsch Schützen Sie Ihre Netzwerke vor extremen Umwelteinflüssen und verheerender elektrostatischer Entladung (ESD), indem Sie abgeschirmte Ethernetkabel in Unternehmensqualität von Ubiquiti Networks verwenden. Weitere Informationen erhalten Sie unter www.ubnt.
Support support.ubnt.com Wiki Page wiki.ubnt.com Support Forum forum.ubnt.com Downloads downloads.ubnt.com www.ubnt.com © 2013 Ubiquiti Networks, Inc. All rights reserved.
