Carrier Class AirMax BaseStation Models: M3/M365/M5
Introduction Introduction Thank you for purchasing a PowerBridge M series product. This is a point-to-point CPE wireless device. This Quick Start Guide is for use with the following models: Model Operating Frequency PowerBridge M3 3300 MHz-3700 MHz PowerBridge M365 3650 MHz-3675 MHz PowerBridge M5 5170-5875 MHz* * Only 5745-5850 MHz is supported in the USA and Canada Package Contents PowerBridge 24V PoE Adapter Power Cord Antenna Bracket Clamps (Qty.
PowerBridge Hardware Installation To install the PowerBridge, perform the following steps: HSt Ro plian Com 1. Use a flathead screwdriver to unlock the PowerBridge case. Turn the screw counter-clockwise until it is loose. The screw remains attached to the compartment. 2. Lift the cover on the PowerBridge by pressing down and raising it up. Connect an Ethernet cable. There is an opening for the Ethernet cable. Slide the cover over the cable and secure it with the screw.
Hardware Installation 3. Insert the M8X135 Carriage Bolts into the Antenna Bracket Clamps. 4. Connect the Antenna Bracket Clamps to the PowerBridge using the four Serrated Flange Bolts.
PowerBridge 5. Mount the PowerBridge to the pole by performing the following steps: a. Position the PowerBridge in the desired mounting location on the pole. b. Slide the Pole Bracket Clamps on to the Carriage Bolts. c. Use the four Serrated Flange Lock Nuts to secure the PowerBridge to the pole.
Hardware Installation 6. Adjust the operating angle of the PowerBridge by adjusting the Serrated Flange Bolts on the top Antenna Bracket Clamp.
PowerBridge 7. Connect the other end of the Ethernet cable from the PowerBridge to the Ethernet port labeled POE on the PoE Adapter.
Hardware Installation 8. Connect an Ethernet cable from your LAN to the Ethernet port labeled LAN on the PoE Adapter. 9. Connect the power cord to the power port on the PoE Adapter. Connect the other end of the power cord to a power outlet.
PowerBridge Accessing the AirOS Utility 1. Make sure that your host machine is connected to the LAN that is connected to the PowerBridge. 2. Configure the Ethernet adapter on your host system with a static IP address on the 192.168.1.x subnet (e.g. 192.168.1.100). 3. Launch your Web browser and type http://192.168.1.20 in the address field and press enter (PC) or return (Mac). 4. The login screen will appear. Enter ubnt in the Username and Password fields. Select your Country and Language.
Specifications Specifications PowerBridge M3/M365/M5 Enclosure Size Weight Max Power Consumption Power Supply Power Method Operating Temperature Operating Humidity 445 x 416 x 34mm 3.
PowerBridge Safety Notices 1. Read, follow, and keep these instructions. 2. Heed all warnings. 3. Only use attachments/accessories specified by the manufacturer. WARNING: Do not use this product in location that can be submerged by water. WARNING: Avoid using this product during an electrical storm. There may be a remote risk of electric shock from lightning. Electrical Safety Information 1.
General Warranty General Warranty UBIQUITI NETWORKS, Inc (“UBIQUITI NETWORKS”) represents and warrants that the Products furnished hereunder shall be free from defects in material and workmanship for a period of one (1) year from the date of shipment by UBIQUITI NETWORKS under normal use and operation. UBIQUITI NETWORKS sole and exclusive obligation under the foregoing warranty shall be to repair or replace, at its option, any defective Product that fails during the warranty period.
PowerBridge Warranty Conditions The foregoing warranty shall apply only if: (I) The Product has not been subjected to misuse, neglect or unusual physical, electrical or electromagnetic stress, or some other type of accident. (II) No modification, alteration or addition has been made to the Product by persons other than UBIQUITI NETWORKS or UBIQUITI NETWORK’S authorized representatives or otherwise approved by UBIQUITI NETWORKS.
Compliance Compliance FCC Changes or modifications not expressly approved by Ubiquiti Networks, Inc. could void the user’s authority to operate the equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause interference, and 2. This device must accept any interference, including interference that may cause undesired operation of the device.
PowerBridge Des renseignements supplémentaires sur l'exposition aux RF est disponible sur Internet à www.fcc.gov/oet/info/documents/ bulletins CE Marking CE marking on this product represents the product is in compliance with all directives that are applicable to it. Alert sign! Follows CE marking Alert sign must be indicated if a restriction on use applied to the product and it must follow the CE marking.
Declaration of Conformity Declaration of Conformity Česky [Czech] UBIQUITI NETWORKS tímto prohla uje, e tento UBIQUITI NETWORKS device, je ve shod se základními po adavky a dal ími p íslu n mi ustanoveními sm rnice 1999/5/ES. Dansk [Danish] Undertegnede UBIQUITI NETWORKS erklærer herved, at følgende udstyr UBIQUITI NETWORKS device, overholder de væsentlige krav og øvrige relevante krav i direktiv 1999/5/EF.
PowerBridge Latviski [Latvian] Ar o UBIQUITI NETWORKS deklar , ka UBIQUITI NETWORKS device, atbilst Direkt vas 1999/5/EK b tiskaj m pras b m un citiem ar to saist tajiem noteikumiem. Lietuviškai [Lithuanian] UBIQUITI NETWORKS deklaruoja, kad šis UBIQUITI NETWORKS įrenginys atitinka esminius reikalavimus ir kitas 1999/5/EB Direktyvos nuostatas.
Ubiquiti Networks Support Email: support@ubnt.com Phone (9 a.m. - 5 p.m. PST): 408-942-1153 Online Resources Wiki Page: www.ubnt.com/wiki Support Forum: www.ubnt.com/forum Knowledge Base: www.ubnt.com/kb Downloads: www.ubnt.com/support/downloads www.ubnt.com © 2011 Ubiquiti Networks, Inc. All rights reserved.
