User's Manual

4. The Main screen will appear and you
should see a live video stream from
the camera.
5. Click the Device tab.
6. Under Wireless Network Settings
section, enter the SSID and Security
settings of your network that is
running the UniFi Video software.
7. Click Save Changes.
8. The UVC-Micro will reboot and
connect to your network.
UniFi Video
Ensure that you are running UniFiVideo
software version 3.1.0 or higher.
The latest version of the UniFi Video
software is available at
downloads.ubnt.com/unifivideo
Once the UVC-Micro and the UniFi
Video software are connected to
the same network, the UniFi Video
auto-management feature should
automatically detect and install your
new camera(s).
For details on using the UniFi Video
software, refer to the User Guide at
documentation.ubnt.com/unifivideo
Specifications
UVC-Micro
Dimensions
(Camera and Base)
40.7 x 40.7 x 40.8 mm
(1.61 x1.61 x 1.61")
Weight
(Camera and Base)
53 g
(1.87oz)
Network Interface 2.4/5 GHz Dual-Band Wi-Fi
Sensor
Progressive Scan
RGB CMOS 1/4"
Lens EFL=2.38 mm / F2.4
View Angle 79.13° (H), 54.15° (V), 88.45° (D)
Night Mode
Infrared LEDs with
Mechanical IR Cut Filter
Video Compression H.264
Resolution 720p HD (1280 x 720)
Max. Frame Rate 30 FPS
Microphone Yes
Speaker Yes
Flash Memory Support microSD (Max. 32 GB)
Power Supply
5.5V Adapter with
5 m (16') Power Cable
Max. Power
Consumption
3.2W
Mounting Wall/Ceiling/Corner Kit Included
Operating
Temperature
0 to 35° C (32 to 95° F)
Operating Humidity 20 to 90% Noncondensing
Safety Notices
1. Read, follow, and keep instructions.
2. Heed all warnings.
3. Only use attachments/accessories specified by
the manufacturer.
WARNING: Do not use this
product in a location that can be
submerged by water.
WARNING: Avoid using this
product during an electrical
storm. There may be a remote risk
of electric shock from lightning.
Electrical Safety Information
1. Compliance is required with respect to voltage,
frequency, and current requirements indicated
on the manufacturer’s label. Connection to a
different power source than those specified
may result in improper operation, damage
to the equipment or pose a fire hazard if the
limitations are not followed.
2. There are no operator serviceable parts inside
this equipment. Service should be provided only
by a qualified service technician.
3. Contact a qualified electrician or the
manufacturer if there are questions about the
installation prior to connecting the equipment.
4. Protective bonding must be installed in
accordance with local national wiring rules and
regulations.
Limited Warranty
UBIQUITI NETWORKS, Inc (“UBIQUITI NETWORKS”)
warrants that the product(s) furnished hereunder
(the “Product(s)”) shall be free from defects in
material and workmanship for a period of one
(1) year from the date of shipment by UBIQUITI
NETWORKS under normal use and operation.
UBIQUITI NETWORKS’ sole and exclusive obligation
and liability under the foregoing warranty shall
be for UBIQUITI NETWORKS, at its discretion, to
repair or replace any Product that fails to conform
to the above warranty during the above warranty
period. The expense of removal and reinstallation
of any Product is not included in this warranty. The
warranty period of any repaired or replaced Product
shall not extend beyond its original term.
Warranty Conditions
The above warranty does not apply if the Product:
(I) has been modified and/or altered, or an
addition made thereto, except by Ubiquiti
Networks, or Ubiquiti Networks’ authorized
representatives, or as approved by Ubiquiti
Networks in writing;
(II) has been painted, rebranded or physically
modified in any way;
(III) has been damaged due to errors or defects
in cabling;
(IV) has been subjected to misuse, abuse,
negligence, abnormal physical,
electromagnetic or electrical stress, including
lightning strikes, or accident;
(V) has been damaged or impaired as a result of
using third party firmware;
(VI) has no original Ubiquiti MAC label, or is missing
any other original Ubiquiti label(s); or
(VII) has not been received by Ubiquiti within
30days of issuance of the RMA.
In addition, the above warranty shall apply only if:
the product has been properly installed and used at
all times in accordance, and in all material respects,
with the applicable Product documentation; all
Ethernet cabling runs use CAT5 (or above), and for
outdoor installations, shielded Ethernet cabling is
used, and for indoor installations, indoor cabling
requirements are followed.
Returns
No Products will be accepted for replacement
or repair without obtaining a Return Materials
Authorization (RMA) number from UBIQUITI
NETWORKS during the warranty period, and the
Products being received at UBIQUITI NETWORKS’
facility freight prepaid in accordance with the RMA
process of UBIQUITI NETWORKS. Products returned
without an RMA number will not be processed and
will be returned freight collect or subject to disposal.
Information on the RMA process and obtaining an
RMA number can be found at:
www.ubnt.com/support/warranty
Disclaimer
EXCEPT FOR ANY EXPRESS WARRANTIES PROVIDED
HEREIN, UBIQUITI NETWORKS, ITS AFFILIATES,
AND ITS AND THEIR THIRD PARTY DATA, SERVICE,
SOFTWARE AND HARDWARE PROVIDERS HEREBY
DISCLAIM AND MAKE NO OTHER REPRESENTATION
OR WARRANTY OF ANY KIND, EXPRESS, IMPLIED
OR STATUTORY, INCLUDING, BUT NOT LIMITED TO,
REPRESENTATIONS, GUARANTEES, OR WARRANTIES
OF MERCHANTABILITY, ACCURACY, QUALITY OF
SERVICE OR RESULTS, AVAILABILITY, SATISFACTORY
QUALITY, LACK OF VIRUSES, QUIET ENJOYMENT,
FITNESS FOR A PARTICULAR PURPOSE AND
NON-INFRINGEMENT AND ANY WARRANTIES
ARISING FROM ANY COURSE OF DEALING, USAGE
OR TRADE PRACTICE IN CONNECTION WITH SUCH
PRODUCTS AND SERVICES. BUYER ACKNOWLEDGES
THAT NEITHER UBIQUITI NETWORKS NOR ITS
THIRD PARTY PROVIDERS CONTROL BUYER’S
EQUIPMENT OR THE TRANSFER OF DATA OVER
COMMUNICATIONS FACILITIES, INCLUDING THE
INTERNET, AND THAT THE PRODUCTS AND SERVICES
MAY BE SUBJECT TO LIMITATIONS, INTERRUPTIONS,
DELAYS, CANCELLATIONS AND OTHER PROBLEMS
INHERENT IN THE USE OF COMMUNICATIONS
FACILITIES. UBIQUITI NETWORKS, ITS AFFILIATES
AND ITS AND THEIR THIRD PARTY PROVIDERS
ARE NOT RESPONSIBLE FOR ANY INTERRUPTIONS,
DELAYS, CANCELLATIONS, DELIVERY FAILURES,
DATA LOSS, CONTENT CORRUPTION, PACKET LOSS,
OR OTHER DAMAGE RESULTING FROM ANY OF THE
FOREGOING. In addition, UBIQUITI NETWORKS does
not warrant that the operation of the Products will
be error-free or that operation will be uninterrupted.
In no event shall UBIQUITI NETWORKS be
responsible for damages or claims of any nature
or description relating to system performance,
including coverage, buyer’s selection of products
(including the Products) for buyer’s application and/
or failure of products (including the Products) to
meet government or regulatory requirements.
Limitation of Liability
EXCEPT TO THE EXTENT PROHIBITED BY LOCAL LAW,
IN NO EVENT WILL UBIQUITI OR ITS SUBSIDIARIES,
AFFILIATES OR SUPPLIERS BE LIABLE FOR DIRECT,
SPECIAL, INCIDENTAL, CONSEQUENTIAL OR OTHER
DAMAGES (INCLUDING LOST PROFIT, LOST DATA,
OR DOWNTIME COSTS), ARISING OUT OF THE USE,
INABILITY TO USE, OR THE RESULTS OF USE OF
THE PRODUCT, WHETHER BASED IN WARRANTY,
CONTRACT, TORT OR OTHER LEGAL THEORY, AND
WHETHER OR NOT ADVISED OF THE POSSIBILITY OF
SUCH DAMAGES.
Note
Some countries, states and provinces do not allow
exclusions of implied warranties or conditions, so
the above exclusion may not apply to you. You
may have other rights that vary from country to
country, state to state, or province to province.
Some countries, states and provinces do not allow
the exclusion or limitation of liability for incidental
or consequential damages, so the above limitation
may not apply to you. EXCEPT TO THE EXTENT
ALLOWED BY LOCAL LAW, THESE WARRANTY TERMS
DO NOT EXCLUDE, RESTRICT OR MODIFY, AND ARE
IN ADDITION TO, THE MANDATORY STATUTORY
RIGHTS APPLICABLE TO THE LICENSE OF ANY
SOFTWARE (EMBEDDED IN THE PRODUCT) TO YOU.
The United Nations Convention on Contracts for the
International Sale of Goods shall not apply to any
transactions regarding the sale of the Products.
Compliance
FCC
Changes or modifications not expressly approved by
the party responsible for compliance could void the
user’s authority to operate the equipment.
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions.
1. This device may not cause harmful interference,
and
2. This device must accept any interference
received, including interference that may cause
undesired operation.
This equipment has been tested and found to
comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against
harmful interference in a residential installation. This
equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful
interference to radio communications. However,
there is no guarantee that interference will not occur
in a particular installation. If this equipment does
cause harmful interference to radio or television
reception, which can be determined by turning the
equipment off and on, the user is encouraged to try
to correct the interference by one or more of the
following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment
and receiver.
• Connect the equipment into an outlet on a
circuit different from that to which the receiver
is connected.
• Consult the dealer or an experienced radio/TV
technician for help.
Operations of this equipment in a residential area
is likely to cause harmful interference in which case
the user will be required to correct the interference
at his own expense.
This radio transmitter FCC ID: SWX-MICRO has been
approved by FCC to operate with the antenna types
listed below with the maximum permissible gain
and required antenna impedance for each antenna
type indicated. Antenna types not included in this
list, having a gain greater than the maximum gain
indicated for that type, are strictly prohibited for use
with this device.
Antenna Information:
Antenna type: Metal Antenna
Antenna gain: 1 dBi
Industry Canada
CAN ICES-3(B)/NMB-3(B)
To reduce potential radio interference to other
users, the antenna type and its gain should be so
chosen that the equivalent isotropically radiated
power (e.i.r.p.) is not more than that permitted for
successful communication.
This device complies with Industry Canada licence-
exempt RSS standard(s). Operation is subject to the
following two conditions:
1. This device may not cause interference, and
2. This device must accept any interference,
including interference that may cause undesired
operation of the device.
Users should also be advised that high-power radars
are allocated as primary users (i.e. priority users)
of the band 5650-5850 MHz and that these radars
could cause interference and/or damage to LE-LAN
devices. This radio transmitter (IC: 6545A-MICRO) has
been approved by Industry Canada to operate with
the antenna types listed below with the maximum
permissible gain and required antenna impedance
for each antenna type indicated. Antenna types not
included in this list, having a gain greater than the
maximum gain indicated for that type, are strictly
prohibited for use with this device.
Antenna Information:
Antenna type: Metal Antenna
Antenna gain: 1 dBi
CAN ICES-3(B)/NMB-3(B)
Pour réduire le risque d’interférence aux autres
utilisateurs, le type d’antenne et son gain doivent
être choisies de façon que la puissance isotrope
rayonnée équivalente (PIRE) ne dépasse pas ce qui
est nécessaire pour une communication réussie.
Cet appareil est conforme à la norme RSS Industrie
Canada exempts de licence norme(s). Son
fonctionnement est soumis aux deux conditions
suivantes:
1. Cet appareil ne peut pas provoquer
d’interférences et
2. Cet appareil doit accepter toute interférence, y
compris les interférences qui peuvent causer un
mauvais fonctionnement du dispositif.
Les utilisateurs devraient également noter que
radars haute puissants sont alloués comme
principaux utilisateurs (c’est-à-dire les utilisateurs
de priorité) des bandes et 5650 à 5850 MHz et
que ces radars pourraient causer des interférences
ou dommages aux dispositifs LAN. Cet émetteur
radio (IC: 6545A-MICRO) a été approuvée par
Industrie Canada pour l’exploitation avec l’antenne
types énumérés ci-dessous avec le gain maximal
admissible et requis l’impédance de l’antenne pour
chaque type d’antenne indiqué. Types d’antenne
non inclus dans cette liste, ayant un gain supérieur
au gain maximal indiqué pour ce type, sont
strictement interdits pour une utilisation avec cet
appareil. Immédiatement suite à la remarque, le
fabricant doit fournir une liste de tous les types
d’antenne approuvé pour une utilisation avec
l’émetteur, ce qui indique le gain maximal d’antenne
permis (en dBi) et requis d’impédance pour chacun.
Informations d’antenne:
Type d’antenne: antenne métallique
Gain d’antenne: 1 dBi
RF Exposure Warning
The antennas used for this transmitter must be
installed to provide a separation distance of at least
20 cm from all persons and must not be located or
operating in conjunction with any other antenna
or transmitter, except as listed for this product’s
certification.
Les antennes utilisées pour cet émetteur doit être
installé pour fournir une distance de séparation d’au
moins 20 cm de toutes les personnes et ne doit pas
être situé ou opérant en conjonction avec une autre
antenne ou un autre émetteur, sauf dans les cas
énumérés à la certification de ce produit.
CE Marking
CE marking on this product represents theproduct is
in compliance with all directives that are applicable
to it.
©2014 Ubiquiti Networks, Inc. All rights reserved. Ubiquiti,
Ubiquiti Networks, the Ubiquiti U logo, the Ubiquiti beam
logo, and UniFi are trademarks or registered trademarks
of Ubiquiti Networks, Inc. in the United States and in other
countries. All other trademarks are the property of their
respective owners.
PH111214
www.ubnt.com
Online Resources
Support support.ubnt.com
Community community.ubnt.com
Downloads downloads.ubnt.com
5150~5250 MHz for indoor used only
5150 ~ 5250 MHz pour l'intérieur utilisé uniquement