User's Manual

ManualsBrandsUbiquiti Networks ManualsElectronicsAccess Point

High-Performance

Integrated InnerFeed

™

airMAX

Bridge

Model: NBE-M5AC-500

Introduction

Thank you for purchasing the Ubiquiti Networks

™

NanoBeam

™

This Quick Start Guide is designed to guide you through

the installation, and show you how to access the airOS®

Configuration Interface. This Quick Start Guide also includes the

warranty terms and is for use with the

NanoBeamM5AC, model

NBE-M5AC-500.

Package Contents

Dish Reflector Radome Antenna Feed

Rear Housing Dish Bracket Pole Clamp U-Bolt

High-Performance

Integrated InnerFeed

™

airMAX

Bridge

Model: NBE-M5AC-500

Flange Nuts

(M8, Qty. 2)

Gigabit PoE

Adapter

(24V, 0.5A)

Power Cord Quick Start Guide

cable and earth grounding must be used as conditions of product warranty. TOUGHCable

™

is designed for outdoor installations. It is the customer’s responsibility to follow local country

regulations, including operation within legal frequency channels, output power, and Dynamic

Frequency Selection (DFS) requirements.

Hardware Overview

Bottom View

Cable Door

Rear Housing

Technology

Ethernet Port

Release

Button Slot

Dish Bracket

Release Button

Dish

Reflector

Alignment Pins

Reset Button

Antenna Feed

Radome

Reset Button To reset to factory defaults, press and hold the

Reset button for more than 10 seconds while the NanoBeam

is already poweredon. Alternatively, the NanoBeam may be

reset remotely via a Reset button located on the bottom of the

Gigabit PoE Adapter.

RESET

MODEL MODELO GP A240 050G

.:INPUT ENTRADA/ 100 240V 50 60Hz MAX 0 3A

/ : .OUTPUT SAÍDA DC 24V 0 5A

+ , ) ,-(,)(45pins 78pins

ITE POWERSUPPLY. . .

XXXX XXXXXXX-

E325

BRASILOCP0004

Rheinland

TUV

Rheinland

ArgentinaS A

. .

TUV

LPS...

Switching Gigabit Power Supply POE

PARAUTILIZAÇÃO COM EQUIPAMENTO

E C

UE ELÉCTRI CO

DETECNOLOGIA DE INFORMAÇÃO

APEN

AS U

ÇÃO E

COS

WAR

ING

K O

F E

TRIC SHOCK

DO NOTOPEN

MADE IN CHINA

Ubiquiti Networks Inc

Reset

Button

Release Button After you assemble the NanoBeam, check the

Release button; it should be fully engaged in the Release Button

Slot of the Rear Housing. This ensures that the Antenna Feed is

locked into place. If you need to remove the Antenna Feed, you

must depress the Release button first.

LEDs

Signal In airOS, you can modify the wireless signal

strength threshold values for each LED on the

Advanced tab under Signal LED Thresholds. The

default values are shown below:

LED will light blue when the wireless signal

strength is above -65 dBm.

LED will light blue when the wireless signal

strength is above -73 dBm.

LED will light blue when the wireless signal

strength is above -80 dBm.

LED will light blue when the wireless signal

strength is above -94 dBm.

Ethernet The Ethernet LED will light steady blue

when an active Ethernet connection is made and

flash when there is activity.

Power The Power LED will light blue when the

device is connected to a power source.

Application Examples

The NanoBeam mounted outdoors with the Dish Reflector

installed provides directional outdoor coverage (gain is

reflector‑dependent).

The NanoBeam mounted outdoors without the Dish Reflector

installed provides outdoor‑to‑indoor coverage using the 3 dBi

Antenna Feed only.

Installation Requirements

• 13 mm or ½" wrench

• Shielded Category 5 (or above) cabling should be used for

all wired Ethernet connections and should be grounded

through the AC ground of the PoE.

We recommend that you protect your networks from the

most brutal environments and devastating ESD attacks

with industrial‑grade shielded Ethernet cable from Ubiquiti

Networks. For more details, visit www.ubnt.com/toughcable

Installation

1. Align and insert the tabs of the Dish Bracket into the

slots of the Dish Reflector. Rotate the Dish Bracket

counter‑clockwise until the tabs lock into place.

2. Line up the Alignment Pins of the Rear Housing with the

alignment holes of the Dish Bracket. Insert the pins and

push until they lock intoplace.

*720-00075-01*

720-00075-01

3. Push in the sides of the Cable Door and detach it from the

Rear Housing.

4. Attach the Antenna Feed:

a. Insert the Antenna Feed into the Rear Housing, and push

until it locks into place with a click.

b. Lightly pull the Antenna Feed to ensure that it is locked

into place and the Release button is fully engaged.

Release Button

Bottom View

5. Connect the Ethernet cable:

a. Connect an Ethernet cable to the Ethernet Port of the

Antenna Feed.

b. Re-attach the Cable Door to the Rear Housing.

6. Slide the Pole Clamp onto the Dish Bracket.

7. Insert the U-Bolt into the Pole Clamp and Dish Bracket. Secure

each end of the U-Bolt with a Flange Nut.

25 N-m

(18 lb-ft)

Note: The mounting assembly can accommodate a

Ø 1.25" - 2.2" pole.

8. Align the arrows on the bottoms of the Radome and Dish

Reflector so the Drain Holes on the Radome point downward.

Snap the Radome onto the Dish Reflector.

9. Connect the other end of the Ethernet cable from the

NanoBeam to the Ethernet port labeled POE on the

PoEAdapter.

10. Connect an Ethernet cable from your LAN or computer to

the Ethernet port labeled LAN on the Gigabit PoE Adapter.

11. Connect the Power Cord to the power port on the Gigabit

PoE Adapter. Connect the other end of the Power Cord to a

power outlet.

Accessing airOS

Verify connectivity in the airOS Configuration Interface.

1. Make sure that your host machine is connected via

Ethernet to the NanoBeam.

2. Configure the Ethernet adapter on your host system with a

static IP address on the 192.168.1.x subnet.

3. Launch your web browser and type https://192.168.1.20

in the address field. Press enter (PC) or return (Mac).

4. The login screen will appear. Enter ubnt in the Username

and Password fields. Select your Country and Language.

You must agree to the Terms of Use to use the product.

Click Login.

Note: U.S. product versions are locked to the

U.S. Country Code to ensure compliance with

FCCregulations.

5. Select the NanoBeam Dish Reflector size:

a. Click the Wireless tab.

b. From the Antenna drop-down list, select the

appropriate option.

c. Click Change to save.

d. Click OK to confirm.

Customize additional settings as needed to complete

the configuration. For additional details on the airOS

Configuration Interface, refer to the User Guide available at

documentation.ubnt.com/airmax

NanoBeam_M5AC-500_QSG_V10_10-22-13_Foldout.indd 1 10/23/13 3:39 PM

Summary of content (3 pages)

PAGE 1
Hardware Overview ™ Release Button After you assemble the NanoBeam, check the Release button; it should be fully engaged in the Release Button Slot of the Rear Housing. This ensures that the Antenna Feed is locked into place. If you need to remove the Antenna Feed, you must depress the Release button first. Bottom View Application Examples Installation The NanoBeam mounted outdoors with the Dish Reflector installed provides directional outdoor coverage (gain is reflector‑dependent). 1.
PAGE 2
Installer Compliance Responsibility Safety Notices Limited Warranty Disclaimer Note Devices must be professionally installed and it is the professional installer's responsibility to make sure the device is operated within local country regulatory requirements. 1. Read, follow, and keep these instructions. 2. Heed all warnings. 3. Only use attachments/accessories specified by the manufacturer.
PAGE 3
Installer Compliance Responsibility Devices must be professionally installed and it is the professional installer's responsibility to make sure the device is operated within local country regulatory requirements. Specifications Dimensions 140 x 140 x 54 mm (Mount Included) Weight Outdoor UV Stabilized Plastic 24V, 0.5A PoE Adapter (Included) Passive PoE (Pairs 4, 5+; 7,8 Return) 3. Only use attachments/accessories specified by the manufacturer.