0 GHz Carrier Class airMAX BaseStation with Dish Antenna Model: PBM10
Introduction Thank you for purchasing the Ubiquiti Networks™ PowerBridge™M. This Quick Start Guide is designed to guide you through the installation, and show you how to access the airOS™ Configuration Interface. This Quick Start Guide also includes the warranty terms and is for use with the PowerBridgeM10, model PBM10. Package Contents Radio Dish Stabilizer Brackets (Qty. 2) M10x25 Bolts (Qty. 3) M10 Hex Nuts (Qty. 9) Feed Elevation Rod O-Ring (Installed on feed) M16 Hex Nuts (Qty.
Installation Requirements • Adjustable wrench or one 16 mm and one 24 mm wrench • Phillips screwdriver • Shielded Category 5 (or above) cabling should be used for all wired Ethernet connections and should be grounded through the AC ground of the PoE. We recommend that you protect your networks from the most brutal environments and devastating ESD attacks with industrial‑grade shielded Ethernet cable from Ubiquiti Networks. For more details, visit www.ubnt.
2. On the front of the Dish, use the four M4x18 Screw and Washer Assemblies to secure the Radio to the Dish.
3. Connect the Elevation Rod to the back of the Dish using a M10x25 Bolt, a M10 Washer, a M10 Spring Lock Washer, and a M10 Hex Nut. Install a M16 Hex Nut about halfway down on the Elevation Rod and then install a M16 Washer on the Elevation Rod. 4. Insert the four M10x150 Carriage Bolts into the Mounting Bracket.
5. Connect the Mounting Bracket to the Dish: a. Insert two M10x25 Bolts through the bottom of the Mounting Bracket and through the Dish. The bolts should be on the inside facing outward. b. Secure each bolt using a M10 Washer, a M10 Spring Lock Washer, and a M10 Hex Nut. c. Slide the Mounting Bracket onto the Elevation Rod. d. Secure the Mounting Bracket to the Elevation Rod using a M16 Washer, a M16 Spring Lock Washer, and a M16 Hex Nut.
6. Lift the cover on the Radio by pressing down and raising it up. Connect an Ethernet cable to the Radio and place the cover back on the Radio. There is an opening for the Ethernet cable. Slide the cover over the cable. 7. Make sure the O-Ring is secure on the Feed.
. On the front of the Dish, connect the Feed to the Radio and Dish using the four M4x12 Screw and Washer Assemblies. Note: DO NOT handle the assembled unit by the feed at any time, especially during installation of the Dish to the pole. Always hold the Dish or the brackets while installing the product. 9. Attach the Stabilizer Brackets to the pole just beneath the area where the Dish will be attached. Use two M10x100 Bolts, two M10 Washers, two M10 Spring Lock Washers, and two M10 Hex Nuts.
10. Place the Pole Clamps on the other side of the pole that the Dish will be mounted on and connect them to the Mounting Bracket using M10 Washers, M10 Spring Lock Washers, and M10 Hex Nuts.
11. Adjust the Azimuth and Elevation. Azimuth can be adjusted by rotating the antenna while supported by the stabilizer bracket. Elevation is adjusted by loosening the Elevation Rod. Tighten all bolts and nuts to approximately 50 N-m (37 lb-ft) or less to avoid deforming the pole. Elevation Azimuth 12. Connect the other end of the Ethernet cable from the Radio to the Ethernet port labeled POE on the PoE Adapter.
13. Connect an Ethernet cable from your LAN to the Ethernet port labeled LAN on the PoE Adapter. 14. Connect the power cord to the power port on the PoE Adapter. Connect the other end of the power cord to a power outlet.
Accessing airOS™ Verify connectivity in the airOS Configuration Interface. 1. Make sure that your host machine is connected to the LAN that is connected to the PowerBridgeM10. 2. Configure the Ethernet adapter on your host system with a static IP address on the 192.168.1.x subnet. 3. Launch your web browser. Type https://192.168.1.20 in the address field and press enter (PC) or return (Mac). 4. The login screen will appear. Enter ubnt in the Username and Password fields. Select your Country and Language.
Installer Compliance Responsibility Devices must be professionally installed and it is the professional installer’s responsibility to make sure the device is operated within local country regulatory requirements. Since Ubiquiti Networks equipment can be paired with a variety of antennas and cables, the Antenna Gain, Cable Loss, and Output Power fields are provided to the professional installer to assist in meeting regulatory requirements.
Czech Republic The content in this section is for exclusive use in the Czech Republic; you are instructed to look for clear channels and manually set the channel to be used. Important Steps to Take before First Use 1. Search for channels that are already used in your area. For these channels, search for the pair channels. NEVER use these channels for operation of your link. 2. In the airOS Configuration Interface of the PowerBridgeM10, activate the Frequency Scan List option and click the Edit button. 3.
Specifications PowerBridgeM10 Radio Dimensions 170 x 250 x 53 mm (without the Feed) 170 x 250 x 272 mm (with the Feed) Weight 1.15 kg (without Feed) 1.2 kg (with Feed) 11 kg (with Feed, Dish, and Mount) Networking Interface Enclosure Characteristics Mounting Kit (1) 10/100 Ethernet Port Die-Cast Aluminum Pole-Mounting Kit Included Max.
Safety Notices 1. Read, follow, and keep these instructions. 2. Heed all warnings. 3. Only use attachments/accessories specified by the manufacturer. WARNING: Do not use this product in location that can be submerged by water. WARNING: Avoid using this product during an electrical storm. There may be a remote risk of electric shock from lightning. Electrical Safety Information 1.
Limited Warranty UBIQUITI NETWORKS, Inc (“UBIQUITI NETWORKS”) warrants that the product(s) furnished hereunder (the “Product(s)”) shall be free from defects in material and workmanship for a period of one (1) year from the date of shipment by UBIQUITI NETWORKS under normal use and operation.
Disclaimer EXCEPT FOR ANY EXPRESS WARRANTIES PROVIDED HEREIN, UBIQUITI NETWORKS, ITS AFFILIATES, AND ITS AND THEIR THIRD PARTY DATA, SERVICE, SOFTWARE AND HARDWARE PROVIDERS HEREBY DISCLAIM AND MAKE NO OTHER REPRESENTATION OR WARRANTY OF ANY KIND, EXPRESS, IMPLIED OR STATUTORY, INCLUDING, BUT NOT LIMITED TO, REPRESENTATIONS, GUARANTEES, OR WARRANTIES OF MERCHANTABILITY, ACCURACY, QUALITY OF SERVICE OR RESULTS, AVAILABILITY, SATISFACTORY QUALITY, LACK OF VIRUSES, QUIET ENJOYMENT, FITNESS FOR A PARTICULAR PUR
Note Some countries, states and provinces do not allow exclusions of implied warranties or conditions, so the above exclusion may not apply to you. You may have other rights that vary from country to country, state to state, or province to province. Some countries, states and provinces do not allow the exclusion or limitation of liability for incidental or consequential damages, so the above limitation may not apply to you.
Industry Canada This Class A digital apparatus complies with Canadian ICES-003. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that permitted for successful communication. This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: 1. This device may not cause interference, and 2.
NB-Indentification Number (if there is any) Notified body number is indicated if it is involved in the conformity assessment procedure. Please check the CE mark on the product label to find out which notified body was involved during assessment. RoHS/WEEE Compliance Statement English European Directive 2002/96/EC requires that the equipment bearing this symbol on the product and/or its packaging must not be disposed of with unsorted municipal waste.
Español La Directiva 2002/96/CE de la UE exige que los equipos que lleven este símbolo en el propio aparato y/o en su embalaje no deben eliminarse junto con otros residuos urbanos no seleccionados. El símbolo indica que el producto en cuestión debe separarse de los residuos domésticos convencionales con vistas a su eliminación.
Declaration of Conformity Česky [Czech] UBIQUITI NETWORKS tímto prohla uje, e tento UBIQUITI NETWORKS device, je ve shod se základními po adavky a dal ími p íslu n mi ustanoveními sm rnice 1999/5/ES. Dansk [Danish] Undertegnede UBIQUITI NETWORKS erklærer herved, at følgende udstyr UBIQUITI NETWORKS device, overholder de væsentlige krav og øvrige relevante krav i direktiv 1999/5/EF.
Italiano [Italian] Con la presente UBIQUITI NETWORKS dichiara che questo UBIQUITI NETWORKS device, è conforme ai requisiti essenziali ed alle altre disposizioni pertinenti stabilite dalla direttiva 1999/5/CE. Latviski [Latvian] Ar o UBIQUITI NETWORKS deklar , ka UBIQUITI NETWORKS device, atbilst Direkt vas 1999/5/EK b tiskaj m pras b m un citiem ar to saist tajiem noteikumiem.
