airMAX™ Carrier Class 2x2 PtP Bridge Dish Antenna Model: RD-3G26
Introduction Thank you for purchasing the Ubiquiti Networks™ RocketDish™, an airMAX™ Carrier Class 2x2 PtP Bridge Dish Antenna. This Quick Start Guide is designed to guide you through the installation of the antenna. This Quick Start Guide also includes the warranty terms and is for use with the RocketDish, model RD-3G26. Package Contents Dish Reflector Protective Shroud Antenna Feed Pole Clamps (Qty. 2) Elevation Rod Main Mounting Bracket Stabilizer Brackets (Qty. 2) M10x150 Carriage Bolts (Qty.
Installation Requirements • RocketM3/M3 GPS or RocketM365/M365 GPS (sold separately) • Phillips #1 screwdriver • 16 mm or 5/8 in. wrench • 24 mm wrench • Shielded Category 5 (or above) cabling should be used for all wired Ethernet connections and should be grounded through the AC ground of the PoE. We recommend that you protect your networks from the most brutal environments and devastating ESD attacks with industrial‑grade shielded Ethernet cable from Ubiquiti Networks. For more details, visit www.ubnt.
Hardware Installation Important: Handle the Dish Reflector with care. Deformations in its shape may reduce the RocketDish's effectiveness. 1. Each M4 Bolt includes a lock washer. Remove these and use them to secure the bolts when assembling. 2. The Dish Reflector and Antenna Feed are keyed so the Antenna Feed can only be installed in a single orientation. Attach the Antenna Feed to the Dish Reflector in the following steps: a.
3. Attach the RF Cables to the connectors labeled Chain 0 and Chain 1 on the RocketM. 4. Attach the RocketM to the Dish Reflector. a. Align the mounting tabs on the back of the RocketM with the Rocket Mounting Bracket located below the Antenna Feed. b. Slide the RocketM down to lock it into place.
5. Attach the other ends of the RF Cables to the RF connectors on the Antenna Feed. 6. Attach the Protective Shroud. a. Align the arrow on the top of the shroud with the short hash mark on the Dish Reflector. b. Rotate the shroud clockwise until it aligns with the long hash mark to lock into place.
. The Elevation Rod includes washers and nuts. Remove one washer, one spring lock washer, and one nut. Use them to secure the Elevation Rod when assembling. 8. Attach the Elevation Rod to the Main Mounting Bracket. a. Insert the Elevation Rod into the Main Mounting Bracket. b. Secure the Elevation Rod with the washer, spring lock washer, and nut. 9. Each M10x150 Carriage Bolt includes a washer, spring lock washer, and nut. Remove these and use them to secure the bolts when assembling in step 15. 10.
11. Each M10x25 Carriage Bolt includes a washer, spring lock washer, and nut. Remove these and use them to secure the bolts when assembling. 12. Attach the RocketDish to the Main Mounting Bracket. a. Insert one M10x25 Carriage Bolt into the RocketDish and Elevation Rod. b. Insert two M10x25 Carriage Bolts into the RocketDish and lower section of the Main Mounting Bracket. c. Secure each M10x25 Carriage Bolt with one washer, one spring lock washer, and one nut.
13. Each M10x100 Bolt includes a washer, spring lock washer, and nut. Remove these and use them to secure the bolts when assembling. 14. Attach the Stabilizer Brackets to the pole just beneath the area where the RocketDish will be attached. Note: The mounting assembly can accommodate a Ø 1.5" - 4.0" pole. a. Place one Stabilizer Bracket on each side of the pole. b. Insert the two M10x100 Bolts into the Stabilizer Brackets. c. Secure each M10x100 Bolt with one washer, one spring lock washer, and one nut. d.
15. Attach the Main Mounting Bracket to the pole just above the Stabilizer Brackets. a. Slide a Pole Clamp over each pair of M10x150 Carriage Bolts. b. Secure each M10x150 Carriage Bolt with one washer, one spring lock washer, and one nut.
16. Visually align the azimuth and elevation. a. To adjust the azimuth, rotate the RocketDish while it is supported by the Stabilizer Brackets. b. To adjust the elevation angle, tighten or loosen the nuts on the Elevation Rod so that the RocketDish is set to the desired tilt. c. Tighten all bolts and nuts to approximately 50 N-m (37 lb-ft) or less to avoid deforming the pole.
Specifications RocketDish RD-3G26 Dimensions Weight Frequency Gain 650 x 650 x 300 mm 9.8 kg 3.3 - 3.8 GHz 26 dBi HPOL Beamwidth 7° (6 dB) VPOL Beamwidth 7° (6 dB) Front-to-Back Ratio Max. VSWR Wind Survivability Wind Loading Polarization Cross-Pol Isolation ETSI Specification Mounting -33 dB 1.4:1 125 mph 177 lb @ 125 mph Dual Linear 35 dB Min.
Safety Notices 1. Read, follow, and keep these instructions. 2. Heed all warnings. 3. Only use attachments/accessories specified by the manufacturer. WARNING: Do not use this product in location that can be submerged by water. WARNING: Avoid using this product during an electrical storm. There may be a remote risk of electric shock from lightning. Electrical Safety Information 1.
Limited Warranty UBIQUITI NETWORKS, Inc (“UBIQUITI NETWORKS”) warrants that the product(s) furnished hereunder (the “Product(s)”) shall be free from defects in material and workmanship for a period of one (1) year from the date of shipment by UBIQUITI NETWORKS under normal use and operation.
Returns No Products will be accepted for replacement or repair without obtaining a Return Materials Authorization (RMA) number from UBIQUITI NETWORKS during the warranty period, and the Products being received at UBIQUITI NETWORKS’ facility freight prepaid in accordance with the RMA process of UBIQUITI NETWORKS. Products returned without an RMA number will not be processed and will be returned freight collect or subject to disposal.
Limitation of Liability EXCEPT TO THE EXTENT PROHIBITED BY LOCAL LAW, IN NO EVENT WILL UBIQUITI OR ITS SUBSIDIARIES, AFFILIATES OR SUPPLIERS BE LIABLE FOR DIRECT, SPECIAL, INCIDENTAL, CONSEQUENTIAL OR OTHER DAMAGES (INCLUDING LOST PROFIT, LOST DATA, OR DOWNTIME COSTS), ARISING OUT OF THE USE, INABILITY TO USE, OR THE RESULTS OF USE OF THE PRODUCT, WHETHER BASED IN WARRANTY, CONTRACT, TORT OR OTHER LEGAL THEORY, AND WHETHER OR NOT ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
RoHS/WEEE Compliance Statement English European Directive 2002/96/EC requires that the equipment bearing this symbol on the product and/or its packaging must not be disposed of with unsorted municipal waste. The symbol indicates that this product should be disposed of separately from regular household waste streams. It is your responsibility to dispose of this and other electric and electronic equipment via designated collection facilities appointed by the government or local authorities.
Español La Directiva 2002/96/CE de la UE exige que los equipos que lleven este símbolo en el propio aparato y/o en su embalaje no deben eliminarse junto con otros residuos urbanos no seleccionados. El símbolo indica que el producto en cuestión debe separarse de los residuos domésticos convencionales con vistas a su eliminación.
Declaration of Conformity Česky [Czech] UBIQUITI NETWORKS tímto prohla uje, e tento UBIQUITI NETWORKS device, je ve shod se základními po adavky a dal ími p íslu n mi ustanoveními sm rnice 1999/5/ES. Dansk [Danish] Undertegnede UBIQUITI NETWORKS erklærer herved, at følgende udstyr UBIQUITI NETWORKS device, overholder de væsentlige krav og øvrige relevante krav i direktiv 1999/5/EF.
Italiano [Italian] Con la presente UBIQUITI NETWORKS dichiara che questo UBIQUITI NETWORKS device, è conforme ai requisiti essenziali ed alle altre disposizioni pertinenti stabilite dalla direttiva 1999/5/CE. Latviski [Latvian] Ar o UBIQUITI NETWORKS deklar , ka UBIQUITI NETWORKS device, atbilst Direkt vas 1999/5/EK b tiskaj m pras b m un citiem ar to saist tajiem noteikumiem.
