User's Manual

In-Wall Wi-Fi Access Point
Model: UAP-IW
Introduction
Thank you for purchasing the Ubiquiti Networks® UniFi®
In‑Wall Wi‑Fi Access Point. This Quick Start Guide is designed
to guide you through installation and also includes
warrantyterms.
Package Contents
In-Wall 802.11n Access Point
Model: UAP-IW
UAP‑IW Cover Plate Quick Start Guide
TERMS OF USE: It is the customer’s responsibility to follow local country regulations, including
operation within legal frequency channels, output power, indoor cabling requirements, and
Dynamic Frequency Selection (DFS) requirements.
Installation Requirements
• Pre‑installed electrical wall box
• Category 5 (or above) UTP cabling approved for indoor use
• Phillips screwdriver
• UniFi Switch or 802.3.af switch
System Requirements
• Microsoft Windows 7/8 or Mac OS X
• Java Runtime Environment 1.6 (or above)
• Web Browser: Mozilla Firefox, Google Chrome, or Microsoft
Internet Explorer 8 (or above)
Network Topology Requirements
• A DHCP-enabled network (for the AP to obtain an IP address
as well as for the wireless clients after deployment)
• A management station running the UniFi Controller
software, located either on-site and connected to the same
Layer-2 network, or off-site in a cloud or NOC
UAP-AC Outdoor
or
Network Health
www
WAN LAN
WLAN
VOIP
www WAN LAN WLAN VOIP
IP
DNS
GATEWAY
ACTIVE CLIENTS
DOWN
UP
SWITCHES
USERS
GUESTS
DOWN
UP
APS
USERS
GUESTS
DOWN
UP
PHONES
EXTENSION
CALLS IN
CALLS OUT
XXX.XXX.XXX.XXX
XXX.XXX.XXX.XXX
192
0
0
0
0
0
0
162
2
0
0
0
30
4
3
6
0
DASHBOARD
MAP
DEVICES
CLIENTS
CALLS
STATISTICS
INSIGHTS
SETTINGS
CURRENT SITE
Default
REFRESH RATE
2 minutes
Network Health
www
WAN LAN
WLAN
VOIP
www
WAN LAN WLAN VOIP
IP
DNS
GATEWAY
ACTIVE CLIENTS
DOWN
UP
SWITCHES
USERS
GUESTS
DOWN
UP
APS
USERS
GUESTS
DOWN
UP
PHONES
EXTENSION
CALLS IN
CALLS OUT
XXX.XXX.XXX.XXX
XXX.XXX.XXX.XXX
192
0
0
0
0
0
0
162
2
0
0
0
30
4
3
6
0
DASHBOARD
MAP
DEVICES
CLIENTS
CALLS
STATISTICS
INSIGHTS
SETTINGS
CURRENT SITE
Default
REFRESH RATE
2 minutes
O-Site
Cloud/NOC
On-Site
Management
Station
UniFi Switch
UniFi
Security
Gateway
Internet
UAP-AC-PRO
UAP-IW
LAN
WAN
1G
Sample Network Diagram
All UniFi devices support off-site management controllers.
For setup details, see the User Guide on the website:
documentation.ubnt.com/unifi
Hardware Overview
Data
PoE Out + Data Reset
PoE In + Data
PoE Out + Data 10/100 Ethernet port supports data and PoE.
Used to connect an 802.3af device to the LAN.
Data 10/100 Ethernet port supports data only. Used to
connect a client device to the LAN.
PoE In + Data 10/100 Ethernet port supports data and
PoE. Connect this port to the LAN and DHCP server via an
802.3afswitch.
Reset The Reset button serves two functions for the UAP-IW:
• Restart Press and release the Reset button quickly.
• Restore to Factory Default Settings Press and hold the
Reset button for more than five seconds.
LED
LED
LED Color Status
White
Factory default, waiting to be integrated.
Flashing White
Initializing.
Alternating
White/Blue
Device is busy; do not touch or unplug it.
This usually indicates that a process such
as a firmware upgrade is taking place.
Blue
Indicates the device has been successfully
integrated into a network and is working
properly.
Quickly
Flashing Blue
This is used to locate an AP.
When you click Locate in the UniFi
Controller software, the AP will flash. It
will also display the location of the AP on
the map.
Steady Blue
with occasional
flashing
Indicates the device is in an isolated state
(all WLANs are brought down until an
uplink is found).
Hardware Installation
An electrical wall box should be pre-installed with an Ethernet
cable running from the box to an 802.3af switch.
1. Detach the Cover Plate from the UAP-IW.
2. Connect the Ethernet cable in the wall box to the port
labeled PoE IN + DATA.
*640-00195-01*
640-00195-01
3. Place the UAP-IW in the wall box and properly position the
cable to ensure the Ethernet connection is not strained.
Note: If the wall box does not have enough room
to accommodate the UAP-IW without straining the
Ethernet connection, replace the wall box with an
open-end or deeper box.
4. Fasten the top and bottom screws. Adjust the screws to
ensure the mounting plate is flush with the wall for proper
fitting of the Cover Plate.
Note: Do not over-tighten or rely on the force of the
screws to pull the UAP-IW into the wall box.
5. Attach the Cover Plate. Press the Cover Plate into position
until the four mounting clips snap into place. If you are
using your own cover plate, secure it with two screws.
Software Installation
Download and install the latest version of the UniFi Controller
software at: downloads.ubnt.com/unifi
Launch the software and follow the on-screen instructions.
Step-by-step instructions are available in the User Guide
located on our website: documentation.ubnt.com/unifi
After you have installed the software and run the UniFi
Installation Wizard, a login screen will appear for the UniFi
Controller management interface. Enter the Admin Name and
Password that you created and click Login.
You can manage your wireless network and view network
statistics using the UniFi Controller management interface.
For information on configuring and using the UniFi Controller
software, refer to the User Guide.
Specifications
UAP-IW
Dimensions 114.6 x 70.6 x 28.5 mm
(4.51 x 2.78 x 1.12")
Weight 117 g (4.127 oz)
Networking Interface (3) 10/100 Ethernet Ports
Button Reset
Operating Band 2.4 GHz
Antenna Gain 1 dBi
Max. Data Speed 150 Mbps
Max. Range 25 m (82')
Wi-Fi Standards 802.11 b/g/n
Power Method PoE 802.3af
Max. Power Consumption 6W
Max. TX Power 17 dBm
Power Save Supported
Wireless Security WEP, WPA-PSK, WPA-Enterprise
(WPA/WPA2, TKIP/AES)
Certications CE, FCC, IC
VLAN 802.1Q
Advanced QoS Per-User Rate Limiting
Guest Trafc Isolation Supported
Concurrent Clients 100+
Mounting 1-Gang Electrical Wall Box (Not Included)
Operating Temperature -10 to 70° C (14 to 158° F)
Operating Humidity 5 to 95% Noncondensing
Safety Notices
1. Read, follow, and keep these instructions.
2. Heed all warnings.
3. Only use attachments/accessories specified by the manufacturer.
WARNING: Do not use this product in location that can
be submerged by water.
Electrical Safety Information
1. Compliance is required with respect to voltage, frequency, and current
requirements indicated on the manufacturer’s label. Connection to a
different power source than those specified may result in improper
operation, damage to the equipment or pose a fire hazard if the
limitations are not followed.
2. There are no operator serviceable parts inside this equipment. Service
should be provided only by a qualified service technician.