User's Manual
Enterprise WiFi System
Model: UAP-Outdoor+
Introduction
Thank you for purchasing the Ubiquiti Networks
™
UniFi
™
Enterprise WiFi System. The UniFi Enterprise WiFi System
includes the UniFi Controller software, which allows you to
manage your wireless network using a web browser.
This Quick Start Guide includes the warranty terms and is for
use with the UniFi AP-HD, model UAP-HD. The UniFi AP can be
powered by any of the following:
• PoE Adapter (included)
• 48V, PoE 802.3af compliant switch
• Ubiquiti Networks TOUGHSwitch PRO, model TS-8-PRO
The UniFi AP also includes the necessary hardware for
mounting the unit on a wall or a pole.
Installation Requirements
• Flathead screwdriver (for pole-mounting)
• Drill and 6 mm drill bit (for wall-mounting)
• Phillips screwdriver
• Shielded Category 5 (or above) cabling should be used
for all outdoor wired Ethernet connections and should be
grounded through the AC ground of the PoE.
We recommend that you protect your networks from
brutal outdoor environments and devastating ESD
attacks with industrial-grade shielded Ethernet cable from
www.ubnt.com/toughcable
TERMS OF USE: Ubiquiti radio devices must be professionally installed. Shielded Ethernet
cable and earth grounding must be used as conditions of product warranty. TOUGHCable is
designed for outdoor installations. It is the customer’s responsibility to follow local country
regulations, including operation within legal frequency channels, output power, and Dynamic
Frequency Selection (DFS) requirements.
Package Contents
UniFi AP-HD Antennas (Qty. 2) Wall Mount Bracket
Metal Strap M2.9x20 Screws
(Qty. 3)
M3x20 Screw
Anchors (Qty. 3)
Enterprise WiFi System
Models: UAP-HD
48V, 0.5A
PoE Adapter
Power Cord UniFi Controller CD
with User Guide
Quick Start
Guide
System Requirements
• Microsoft Windows Vista, Windows 7, Windows 8, or
• Java Runtime Environment 1.6 (or above)
• Web Browser: Mozilla Firefox, Google Chrome, or Microsoft
Internet Explorer 8 (or above)
Network Topology Requirements
• A DHCP-enabled network for the AP to obtain an IP
address (wireless clients will also obtain IP addresses after
deployment)
• A management station computer running the UniFi
Controller software, located either onsite and connected to
or
Router
O-Site
Cloud/NOC
2
On-Site
Management Station
Wired UAP-PRO
Wired UAP-HD
Wireless
Uplinked
1
UAP
Wired UAP-Outdoor
Sample Network Diagram
1. Refer to the UniFi Enterprise WiFi System User Guide on the CD for
setting up wireless-linked APs.
All UniFi APs support off-site management controllers. See the User
Guide for setup details.
Hardware Overview
LED
LED Color Status
Flashing White
Initializing.
Steady White
Factory default, waiting to be integrated.
Alternating
White/Blue
Device is busy; do not touch or unplug it.
This usually indicates that a process such
as a firmware upgrade is taking place.
Quickly
Flashing Blue
This is used to locate an AP.
When you click Locate in the UniFi
Controller software, the AP will flash. It
will also display the location of the AP on
the map.
Steady Blue
Indicates the device has been successfully
integrated into a network and is working
properly.
Steady Blue
with occasional
flashing
Indicates the device is in an isolated state
(all WLANs are brought down until an
uplink is found).
Ports
Main
Ethernet Port
(10/100 Mbps)
Reset
Button
Secondary
Ethernet Port
(10/100 Mbps)
Secondary The Secondary Ethernet port is used for bridging.
Reset The Reset button serves two functions for the UniFi AP:
•
Restart Press and release the Reset button quickly.
•
Restore to Factory Default Settings Press and hold the
Reset button for more then five seconds.
Main The Main Ethernet port is used to connect the power
and should be connected to the LAN and DHCP server. Power
can be provided by any of the following:
• Included PoE adapter
• 48V, 802.3af compliant switch
• Ubiquiti Networks TOUGHSwitch PRO, model TS-8-PRO
Hardware Installation
The UniFi AP can be mounted to a wall or on a pole. Perform
the steps for the appropriate installation:
Wall Mount
To mount the AP on a wall, use the included Wall Mount
Bracket, Screws, and Screw Anchors.
1. Place the Wall Mount Bracket at the desired location on the
wall, with the one screw hole pointed towards the ground.
2. Use a pencil to mark the three holes on the wall.
3. Use a 6 mm drill bit to drill the holes in the wall.
4. Insert a Screw Anchor into each hole.
5. Secure the Wall Mount Bracket to the wall with the
self-tapping Screws.
6. Align the mounting tabs on the UniFi AP with the notches
on the Wall Mount Bracket, and slide the UniFi AP down
until it locks into place.
Pole Mount
To mount the UniFi AP on a pole, use the included Metal Strap:
1. Turn the screw on the Metal Strap counter-clockwise to
open the strap.
2. Straighten out the end of the Metal Strap and slide it
through the back of the UniFi AP.
3. Wrap the Metal Strap around the pole. Use a flathead
screwdriver to turn the screw clockwise and securely fasten
the strap to the pole.
Antenna Installation
Connect each Antenna to a RP-SMA connector by rotating it
clockwise.
Powering the UniFi AP
The UniFi AP can be powered by the included PoE Adapter or a
compatible PoE switch.
1. Lift the locking tab of the Port Cover and slide the cover
down to remove it.
2. Connect an Ethernet cable to the Main port.