Enterprise Gateway Router with Gigabit Ethernet Model: USG
Introduction Thank you for purchasing the Ubiquiti Networks® UniFi® Security Gateway. This Quick Start Guide is designed to guide you through installation and also includes warranty terms. Package Contents UniFi Security Gateway Power Adapter (12V, 1A) Power Cord Enterprise Gateway Router with Gigabit Ethernet Model: USG Screws (Qty. 2) Screw Anchors (Qty. 2) Quick Start Guide TERMS OF USE: All Ethernet cabling runs must use CAT5 (or above).
UniFi Controller System Requirements • Microsoft Windows 8, Mac OS X, or Linux • Java Runtime Environment 1.6 (or above) • Web Browser: Mozilla Firefox, Google Chrome, Microsoft Edge, or Microsoft Internet Explorer 11 • UniFi Controller software v5.4 or higher (available at: www.ubnt.
Hardware Overview Ports Panel Interface Description Console RJ45 serial console port for CLI management. Use a RJ45‑to‑DB9 serial console cable to connect the Console port to your computer. Then configure using the following settings: • Baud rate 115200 • Data bits 8 • Parity NONE • Stop bits 1 • Flow control NONE Reset Resets to factory defaults. The UniFi Security Gateway should be powered on.
LEDs Status Power Ethernet Console Status Indicator LED Status Speed/Link/Act State Status White Fully Booted; Not Adopted Blue Adopted and Provisioned Alternating White/Blue Device Firmware is Upgrading Blue Flashing Device Locator Activated from UniFi Controller Off Power Off Green Power On Off No Link Amber Link Established at 10/100 Mbps Amber Flashing Link Activity at 10/100 Mbps Green Link Established at 1000 Mbps Green Flashing Link Activity at 1000 Mbps Power Speed/
Hardware Installation The UniFi Security Gateway can be used on a level, stable surface, or mounted to a wall with the included screws and anchors. If you are not going to mount the UniFi Security Gateway on a wall, then skip to the section, Connecting Power. WARNING: To reduce the risk of fire or electric shock, do not expose this product to rain or moisture. WARNING: FAILURE TO PROVIDE PROPER VENTILATION MAY CAUSE FIRE HAZARD.
2. Use a Phillips screwdriver to secure a Screw into each anchor. Leave a clearance of approximately 3 mm between the screw head and the wall. 3 mm 3. Position the UniFi Security Gateway over the Screws, and insert the Screws into the wall-mount slots located on the bottom of the UniFi Security Gateway. Then slide the UniFi Security Gateway down to lock it into place.
Connecting Power 1. Connect the Power Adapter to the power port. 2. Connect the Power Cord to the Power Adapter. Connect the other end of the Power Cord to a grounded power source.
Network Connections 1. Connect an Ethernet cable from a broadband modem or WAN to the WAN 1 port. 2. Connect an Ethernet cable from a network switch to the LAN 1 port. Note: LAN 1 is set to DHCP Server by default.
Software Installation Download and install the latest version of the UniFi Controller software at: www.ubnt.com/download/unifi From a management station connected to the same Layer‑2 network, launch the installer and follow the on-screen instructions. Note: If you already have UniFi Controller v5.4 or higher installed, go to the section, Adopting the UniFi Security Gateway. 1. The Ubiquiti UniFi Controller window will appear. Click Launch a Browser to Manage the Network. 2.
3. The UniFi Controller will discover the UniFi Security Gateway with the default IP Address,192.168.1.1. Select the device, and click Next. 4. Create an SSID (wireless network name) and Security Key. Click Next. If you do not have any UniFi APs on the network, click Skip.
5. Create an Admin Name and Password for super admin access to the UniFi Controller. Confirm the Password, and click Next. 6. Review the UniFi Controller settings. Click Finish to complete the UniFi Setup Wizard.
7. The login screen for the UniFi Controller will appear. Enter the Admin Name and Password that you created in the UniFi Setup Wizard. Click Login. The UniFi Controller dashboard window will appear. Adopting the UniFi Security Gateway 1. From the UniFi Controller dashboard, click Devices in the left menu bar.
2. In the Devices window, locate UniFi Gateway in the list of devices under the Model column. To adopt and provision the gateway, click Adopt. 3. The Status Indicator on the UniFi Security Gateway will turn blue to confirm that it is successfully adopted.
Optional WAN Port Configuration via Layer 3 By default, the WAN port is set to DHCP so it can be assigned network settings by the service provider. To change the setting, connect a computer directly (or through a switch) to the LAN 1 port of the UniFi Security Gateway. 1. From a web browser, gohttps://setup.ubnt.com to https://setup.ubnt.com/ 2. The UniFi Gateway login window will appear. Enter your Username and Password. Click Sign In.
Specifications UniFi Security Gateway Dimensions Weight Networking Interfaces Serial Console Port Data Ports Max. Power Consumption Power Supply Supported Voltage Range LEDs System Serial Console Port Data Ports Layer 3 Forwarding Performance Packet Size: 64 Bytes Packet Size: 512 Bytes or Larger Processor System Memory On-Board Flash Storage Rackmount Operating Temperature Operating Humidity Certifications 135 x 135 x 28.3 mm (5.32 x 5.32 x 1.11") 366 g (12.
Safety Notices 1. Read, follow, and keep these instructions. 2. Heed all warnings. 3. Only use attachments/accessories specified by the manufacturer. WARNING: Failure to provide proper ventilation may cause fire hazard. Keep at least 20 mm of clearance next to the ventilation holes for adequate airflow. WARNING: To reduce the risk of fire or electric shock, do not expose this product to rain or moisture. WARNING: Do not use this product in a location that can be submerged by water.
Limited Warranty UBIQUITI NETWORKS, Inc (“UBIQUITI NETWORKS”) warrants that the product(s) furnished hereunder (the “Product(s)”) shall be free from defects in material and workmanship for a period of one (1) year from the date of shipment by UBIQUITI NETWORKS under normal use and operation.
Disclaimer EXCEPT FOR ANY EXPRESS WARRANTIES PROVIDED HEREIN, UBIQUITI NETWORKS, ITS AFFILIATES, AND ITS AND THEIR THIRD PARTY DATA, SERVICE, SOFTWARE AND HARDWARE PROVIDERS HEREBY DISCLAIM AND MAKE NO OTHER REPRESENTATION OR WARRANTY OF ANY KIND, EXPRESS, IMPLIED OR STATUTORY, INCLUDING, BUT NOT LIMITED TO, REPRESENTATIONS, GUARANTEES, OR WARRANTIES OF MERCHANTABILITY, ACCURACY, QUALITY OF SERVICE OR RESULTS, AVAILABILITY, SATISFACTORY QUALITY, LACK OF VIRUSES, QUIET ENJOYMENT, FITNESS FOR A PARTICULAR PUR
STATUTORY RIGHTS APPLICABLE TO THE LICENSE OF ANY SOFTWARE (EMBEDDED IN THE PRODUCT) TO YOU. The United Nations Convention on Contracts for the International Sale of Goods shall not apply to any transactions regarding the sale of the Products. Compliance FCC Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This device complies with Part 15 of the FCC Rules.
RoHS/WEEE Compliance Statement English European Directive 2012/19/EU requires that the equipment bearing this symbol on the product and/or its packaging must not be disposed of with unsorted municipal waste. The symbol indicates that this product should be disposed of separately from regular household waste streams. It is your responsibility to dispose of this and other electric and electronic equipment via designated collection facilities appointed by the government or local authorities.
Français La directive européenne 2012/19/UE exige que l’équipement sur lequel est apposé ce symbole sur le produit et/ou son emballage ne soit pas jeté avec les autres ordures ménagères. Ce symbole indique que le produit doit être éliminé dans un circuit distinct de celui pour les déchets des ménages.
Nederlands [Dutch] Hierbij verklaart UBIQUITI NETWORKS, dat deze USG apparaat, in overeenstemming is met de essentiële eisen en de andere relevante bepalingen van richtlijnen 2014/30/EU, 2014/35/EU. De volledige tekst van de EU-conformiteitsverklaring kan worden geraadpleegd op het volgende internetadres: www.ubnt.
Polski [Polish] Niniejszym, Ubiquiti Networks, oświadcza, że urządzenie USG, jest zgodny z zasadniczymi wymaganiami oraz pozostałymi stosownymi postanowieniami Dyrektyw 2014/30/UE, 2014/35/UE. Pełny tekst deklaracji zgodności UE jest dostępny pod następującym adresem internetowym: www.ubnt.com/compliance Português [Portuguese] UBIQUITI NETWORKS declara que este dispositivo USG, está conforme com os requisitos essenciais e outras disposições das Directivas 2014/30/UE, 2014/35/UE.
