User's Manual Part 2

ManualsBrandsUbiquiti Networks ManualsElectronicsUniFi SWITCH

Network Topology Requirements

• A DHCP-enabled network for the UniFi Switch to obtain an

IPaddress (connected devices will also obtain IP addresses

after deployment)

• A UniFi Cloud Key or management station running the UniFi

Controller software v5.4.x or above, located either on-site

and connected to the same Layer2 network, or off-site in a

cloud or NOC

US-L2-24-POE

USG-PRO-4

(DHCP Server)

Internet

UAP-AC-SHD

UAP-AC-M-PRO

UAP-AC-HD

LAN

WAN

UniFi Cloud Key

(UniFi Controller)

Remote Access to

UniFi Controller

Sample Network Diagram

All UniFi devices support off-site management controllers.

For setup details, refer to the User Guide on the website:

documentation.ubnt.com/unifi

Summary of content (8 pages)

PAGE 1
Network Topology Requirements • A DHCP-enabled network for the UniFi Switch to obtain an IP address (connected devices will also obtain IP addresses after deployment) • A UniFi Cloud Key or management station running the UniFi Controller software v5.4.
PAGE 2
Hardware Overview Front Panel System LED System State Status Flashing White Initializing. Steady White Factory defaults, waiting for integration. Alternating White/Blue Device is busy; do not touch or unplug it. This usually indicates that a process such as a firmware upgrade is taking place. Steady Blue Unit has been adopted and successfully integrated into a network. The device is working properly. This is used to locate a device.
PAGE 3
Front Panel Port LEDs RJ45 PoE RJ45 Speed/Link/Act SFP+ Speed/Link/Act SFP Speed/Link/Act LED State Status Off No PoE RJ45 Ports PoE Amber IEEE 802.3af/802.
PAGE 4
Front Panel Ports RJ45 1-48 SFP+ 1-2 SFP 1-2 Port Description RJ45 RJ45 ports support Power over Ethernet (PoE) and 10/100/1000 Ethernet connections. SFP+ 1-2 (US-L2-48-POE only) SFP 1-2 Hot-swappable SFP+ ports support 1/10 Gbps connections. Hot-swappable SFP ports support 1 Gbps connections. Front Panel Button Reset Button Description This button serves two functions for the UniFi Switch: Reset • Restart Press and release the Reset button quickly.
PAGE 5
Back Panel Fans Mounting Holes Mounting Holes Console Port PSU Module Slot for Spare PSU Description RJ45 serial console port for Command Line Interface (CLI) management.
PAGE 6
Hardware Installation WARNING: FAILURE TO PROVIDE PROPER VENTILATION MAY CAUSE FIRE HAZARD. KEEP AT LEAST 20 MM OF CLEARANCE NEXT TO THE VENTILATION HOLES FOR ADEQUATE AIRFLOW. WARNING: To reduce the risk of fire or electric shock, do not expose the UniFi Switch to rain or moisture. 1. Connect the Power Cord to the Power port of the PSU Module. 2. Attach the UniFi Switch to the rack using the four Mounting Screws. (If the rack has square slots, then use the Cage Nuts with the Mounting Screws.) 3.
PAGE 7
Connecting Ethernet 1. Connect an Ethernet cable from your computer or host system to any port of the UniFi Switch. 2. Connect Ethernet cables from the Ethernet ports of your devices to the other numbered ports of the UniFi Switch. Using SFP Ports To use an SFP port: 1. Remove the protective plug covering the SFP port. 2. Plug a compatible fiber module into the SFP port.
PAGE 8
05 3. Connect a fiber optic cable to the fiber module. Then connect the other end of the cable to another fiber device. Using SFP+ Ports (US-L2-48-POE only) To use an SFP+ port: 1. Remove the protective plug covering the SFP+ port. 2. Plug a compatible fiber module into the SFP+ port. DDM 20KM 310nm SM/SC ps nm/Rx1 1000Mb Tx1550 05 3. Connect a fiber optic cable to the fiber module. Then connect the other end of the cable to another fiber device.