Specifications

24 OPERATING INSTRUCTIONS DSD 700
SCART Source
This screen allows the user to set the sources for the various
SCART connectors on the decoder.
The options available for each SCART source are:
a. Satellite
b. TV
c. Video recorder
To change the settings of Scart Source screen, do the following:
1 Repeat steps 1 to 6 for setting the TV Type (page 23).
2 Press to highlight SCART Source.
3 Press OK. The SCART Source option is displayed.
4 Press or to set the input signal of the selected SCART
source.
5 Store the setting by pressing OK on the RCU.
6 Press EXIT to return to the previous menu or MENU to return to
the service.
SCART Video Output
This screen allows the user to set the type of SCART video output
for the various SCART outputs on the decoder.
The options available for each SCART output are:
a. TV SCART Output: Composite
RGB
S Video
Not used
NOTE: When Not Used is selected the VCR SCART output
is not displayed.
b. VCR SCART Output: Composite
S Video
To change the settings of the Scart Video Output screen, do the
following:
1 Repeat steps 1 to 6 for setting the TV Type (page 23).
2 Press to highlight SCART Video Output.
3 Press OK. The SCART Video Output screen is displayed.
4 Press to highlight the SCART output to be edited.
5 Press or to set the output signal of the selected
SCART.
6 Store the setting by pressing OK on the RCU.
7 Press EXIT to return to the previous menu or MENU to return to
the service
Change Modem Settings (if fitted)
If a modem is installed in the decoder, the Change Modem Settings
screen allows the user to select Pulse or Dial Tone for the modem,
and (if applicable) to define a prefix string for the modem.
1 Press MENU on the RCU.
The Main Menu options list is displayed.
2 Press to highlight Advanced Options.
3 Press OK.
The Advanced Options Menu is displayed.
4 Press to highlight Change Modem Settings.
5 Press OK.
The Change Modem Settings screen is displayed.
6 Press or to highlight the field to be edited.
7 Edit the Pulse/Tone setting using and .
8 Edit the Prefix digits using the numbered buttons and as
backspace.
9 Press OK to activate the setting and leave the screen.
10 Press EXIT to return to the previous menu or MENU to return to
the service.
Local Time
Greenwich Mean Time is transmitted via the satellite signal and re-
ceived by the IRD. If the user lives in a different time-zone, the IRD must
be set up during installation to show the correct local time for the Local
Time. In order to set the time do the following :
1 Press MENU on the RCU.
The Menu Options list is displayed.
2 Press to highlight Advanced Options.
3 Press OK.
The Advanced Options Menu is displayed.
4 Press to highlight Local Time.
5 Press OK.
The Local Time screen is displayed.
6 Press and to add or subtract offsets of 30 minutes until
the local time displayed shows the actual time for your location.
7 Press OK to save the setting and leave the screen.
8 Press EXIT to return to the previous menu or MENU to return to
the service.
DSD Upgrade
Upgrades involve replacing the software (programs) in the DSD with
improved software, adding more features and improving the existing
operation of the DSD. This ensures that the DSD does not have to be
replaced each time advances in technology occur.
DSD software upgrades normally take place automatically over-the-
air. The DSD can be upgraded when it is in standby or while it is
switched to a channel. The DSD cannot be upgraded if it is switched
off at the mains. It is strongly recommended that your DSD is in standby
when you are not using it (you do this by pressing on the RCU).
The Mail Menu will usually warn you that a software upgrade will take
place.
A facility is provided whereby you can check if new software is
available and you can then start the upgrade yourself. This is
necessary if the DSD has not been upgraded over-the-air due to, for
instance, prolonged power failures.