Quick Start Guide

ManualsBrandsUEi Test Instruments ManualsElectrical EquipmentWireless Pipe Clamp

Quick Start Guide for UEi HUB Tools v2

SETUP:

Download and install the UEi HUB App

Open the App and navigate to the

appropriate Tools Connection Screen for the

tool you wish to connect.

Tap the tool box icon on the Ref Side display

to connect to WPP1, WPC2 and WOT2 tools.

Tap the tool box icon on the Air Side display

to connect to WHP1 tools.

Tap the tool box icon on the Vac display to

connect to WVG2 tools.

Power on the HUB Tools and wait until you

see the flashing green LED.

Summary of content (7 pages)

PAGE 1
Quick Start Guide for UEi HUB Tools v2 SETUP: Download and install the UEi HUB App Open the App and navigate to the appropriate Tools Connection Screen for the tool you wish to connect. Tap the tool box icon on the Ref Side display to connect to WPP1, WPC2 and WOT2 tools. Tap the tool box icon on the Air Side display to connect to WHP1 tools. Tap the tool box icon on the Vac display to connect to WVG2 tools. Power on the HUB Tools and wait until you see the flashing green LED.
PAGE 2
WOT2, WVG2, WPP1 – Press and hold Power button for 1 second. WHP1 – Press the probe release and extend the sensing probe 90° or 180° until it locks in place. WPC2 – Open the clamp jaw by placing a cylinder with a diameter larger than 9mm in the jaw. In the App you will see the tools appear in the “Nearby Tools list”.
PAGE 3
If tools are missing tap the refresh icon and the list will refresh. Touch and Drag a tool from the “Nearby Tool list” to an appropriate assignment slot (Match the tool icon to the slot you wish to assign it to.” To see tool values and associated calculated values return to the Display Screen by tapping the back button. You can swipe between the Vacuum, Refrigerant and Air side displays. You are now ready to monitor live measurements from your UEi HUB tools.
PAGE 4
SPECIFICATIONS: WHP1: Temperature Operating Range: 32 to 60°C (0 to 140°F) Resolution: 0.1° Accuracy: ±0.3°C (±0.5°F) Drift: <0.03°C/yr Relative Humidity Operating Range: 0 to 100% Resolution: 0.1% Accuracy: ±3% Drift: <0.25%/yr Operating Conditions Temperature: -41 to 140°F (5 to 60°C) %RH: 20 to 80% Storage Conditions (Batteries removed) Temperature: -40 to 257°F (-40 to 125°C) Ingress protection IP 52 Power Battery type: 2 AAA Alkaline Batteries Battery Life: 100+ hrs.
PAGE 5
FCC and IC STATEMENT This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
PAGE 6
FCC AND IC NOTICE This device complies with Part 15 of the FCC rules and Industry Canada license-exempt RSS 247. Operation is subject to the following two conditions: (1) This device may not cause harmful interference; and (2) this device must accept any interference received, including interference that may cause undesired operation. Cet appareil est conforme à la partie 15 des règles de la FCC, ainsi qu’à la norme RSS 247 exempte de licence d’Industrie Canada.
PAGE 7
recommended operating positions accepted by the FCC/ RSS with the device transmitting at its highest certified power level in all tested frequency band without distance attaching away from the body. Noncompliance with the above restrictions may result in violation of FCC RF exposure guidelines.