Use and Care Manual

Latex Base DRYLOK® Masonry Waterproofer
Latex Base DRYLOK Masonry Waterproofer
is the manageable way to solve water
seepage problems. Reduces radon gas
penetration by reducing vapor transfer.
Guaranteed to stop water
No pre-mixing or pre-wetting
Resists 10 psi, equivalent to a wall of water
22 ft. high
Fully transferable 10 year warranty
White is tintable
Formulated for waterproong all interior,
exterior, above or below grade masonry
walls, cinder and concrete blocks, stucco and
brick, retaining walls, sh ponds, birdbaths,
basement walls and foundations.
Latex DRYLOK may be applied over previous
coatings in sound condition. but the warranty
is void. Not formulated for horizontal
surfaces subject to foot traffic.
COMPOSITION:
Latex base
SHEEN:
Flat
% WEIGHT SOLIDS:
65-67%
% VOLUME SOLIDS:
48%-50%
DENSITY (LBS./US GAL.):
12.7-12.8
VISCOSITY:
120-130 KU @77ºF
pH:
9.5-9.9
COLORS:
• White – ready mixed formula
• 3 ready mixed colors
DRY TIME:
• To touch: 30 minutes
• To recoat: 3 hours
• Top coat with latex paint: 24 hours
Note: Maximum cure and dry time will
be prolonged when slightly humid and
damp, cool conditions prevail.
CLEAN UP:
Soap and water
Dispose of contaminated absorbent,
container and unused contents in
accordance with local, state and federal
regulations.
COVERAGE (SQ. FT./US GAL.):
• 75-100 sq. ./gal.
Note: Actual coverage will vary
depending upon application method,
surface texture and porosity.
RECOMMENDED FILM THICKNESS/COAT:
• 13-21 wet mils/coat
• 6-10 dry mils/coat
FLASH POINT:
N/A
SHELF LIFE:
Four years
FREEZE/THAW:
ree cycles
CONTAINER SIZES:
One quart (US), one gallon (US), two
gallon (US) and ve gallon (US)
containers
Does not exceed 100 g/L
Tint to light shades with alkali-proof
universal tinting colors. Do not use more
than 2 . oz. of colorant per gallon.
Surface must be clean and free from dirt, dust,
grease, oil, form release compound or paint.
Patch all holes or cracks and the oor/wall
joint with DRYLOK FAST PLUG® or a fast
seing hydraulic cement, and smooth the
patch evenly with the surface around it. Check
the joint where the oor and wall meet and
ll any breaks with DRYLOK FAST PLUG®.
EFFLORESCENCE, a white, powdery,
crystal-like deposit visible on the masonry
surface must be removed.
DRYLOK ETCH or muriatic acid, used
according to manufacturer’s directions, are
effective efflorescence removal agents. All
masonry surfaces are subject to occurrences
of efflorescence.
Old paint in poor condition must be
removed by wire-brushing, sand blasting or
by using other suitable means
May be applied on slightly damp surfaces, but
best results are obtained when applied over
dry surfaces. For best waterproong results,
wait for a dry (rain-free) period.
If you scrape, sand, or remove old paint, you
may release lead dust. LEAD IS TOXIC.
EXPOSURE TO LEAD DUST CAN CAUSE
SERIOUS ILLNESS, SUCH AS BRAIN
DAMAGE, ESPECIALLY IN CHILDREN.
PREGNANT WOMEN SHOULD ALSO
AVOID EXPOSURE. Wear a NIOSH-
approved respirator to control lead
exposure. Clean up carefully with a HEPA
vacuum and a wet mop. Before you start,
®®
UNITED GILSONITE LABORATORIES
MAILING: P.O. Box 70, Scranton, Pennsylvania, 18501
SHIPPING: 1396 Jefferson Avenue, Dunmore, Pennsylvania, 18509
T
OLL FREE: 1-800-UGL-LABS (845-5227)
P
HONE: 1-570-344-1202 • FAX: [phone]
www.ugl.com
D R Y L O K ® M A S O N R Y P R O D U C T S
O V E R
DRY TIME:
30 Minutes
Recoat 3 Hours
CLEAN-UP:
Soap and Water
COVERAGE:
2 Coats Minimum
SPREAD RATE:
100 Sq. Ft./Gallon