Use and Care Guide

ManualsBrandsUGL ManualsCaulkPourable Masonry Crack Filler 32-fl oz Gray Paintable Latex Caulk

SECTION 03 01 00

DRYLOK

Concrete and Masonry Repair and Maintenance Products

PART 1 - GENERAL

1.1 RELATED DOCUMENTS

A. Drawings and general provisions of the Contract, including General and Supplementary

Conditions and Division 01 Specification Sections, apply to this Section.

1.2 SUMMARY

A. Section Includes:

1. Accessories for Concrete and Masonry repair and maintenance as scheduled including the

following:

a. DRYLOK

Concrete Cleaner and Degreaser.

b. DRYLOK

Concrete Patch.

c. DRYLOK

Etch.

d. DRYLOK

Fast Plug

Hydraulic Cement.

e. DRYLOK

Latex Bonding Agent.

f. DRYLOK

Liquid Etch.

g. DRYLOK

Non-Skid Texture Additive.

h. DRYLOK

Masonry Crack Filler.

i. DRYLOK

Pourable Masonry Crack Filler.

B. Related Sections:

1. Section 03 30 00 – Cast-in-Place Concrete.

2. Section 03 41 00 – Precast Structural Concrete.

3. Section 03 47 13 – Tilt-Up Concrete.

4. Section 04 21 00 – Masonry Assemblies Unit Masonry.

5. Section 04 22 00 – Concrete Unit Masonry

6. Section 09 97 26 – Cementitious Coatings

1.3 REFERENCES

A. ASTM International (ASTM)

1. ASTM D 16 – Standard Terminology for Paint, Related Coatings, Materials and

Applications.

Summary of content (4 pages)

PAGE 1
SECTION 03 01 00 DRYLOK® Concrete and Masonry Repair and Maintenance Products PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. 1.2 Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification Sections, apply to this Section. SUMMARY A. Section Includes: 1. Accessories for Concrete and Masonry repair and maintenance as scheduled including the following: a. DRYLOK® Concrete Cleaner and Degreaser. b. DRYLOK® Concrete Patch. c. DRYLOK® Etch. d.
PAGE 2
1.4 ACTION SUBMITTALS A. Submit under provisions of Section 01 30 00. B. Product Data: For each type of product. 1. Include construction details, materials descriptions and tested physical properties. 2. Include manufacturer’s instructions for evaluating, preparing and treating substrate. C. Shop Drawings: 1. Show locations and extent of application. D. Samples: 1. For each product specified, two cured samples, representing actual product color and texture. 1.5 QUALITY ASSURANCE A.
PAGE 3
1.7 PROJECT CONDITIONS A. Environmental Requirements: 1. Do not apply outdoors in rain or when rain is expected within 24 hours. Do not apply above 90 degrees F (32 degrees C) or below 50 degrees F (10 degrees C) or when temperatures are expected to fall below 40 degrees F (4 degrees C) within 24 hours. PART 2 - PRODUCTS 2.1 MANUFACTURERS A. Subject to compliance with requirements, provide products from the following manufacturer: 1.
PAGE 4
G. Lightweight aggregate non-skid texture additive for oil base, latex base, epoxy floor paints and clear coatings. 1. Acceptable Product: a. DRYLOK® Non-Skid Texture Additive. H. Siliconized acrylic gun-grade latex filler for sealing cracks and mortar joint in masonry walls, sidewalks, steps or floors. 1. Acceptable Product: a. DRYLOK® Masonry Crack Filler. I. Siliconized acrylic pourable latex filler for sealing cracks and mortar joints in masonry walls, sidewalks, steps or floors. 1.