Installation Instructions Model: 50005 Size: 52''
Safety Rules Please read all safety instructions prior to installing your ceiling fan and save this document for future reference. If you are in doubt with any of the information provided or difficulty installing your fan, please the email customer service. Before you begin installing the fan, shut power off the circuit breaker for the fuse box. Read all instructions and safety information before installing your new fan. All wiring must be in accordance with national and local electrical codes.
Installation 1 Before Installation . Carefully open the package. Remove items from the box. Place the motor body on carpet or foam to avoid damage to the finish. Do not discard fan cartons or foam inserts in case of return or repair. . To prevent injury and damage, ensure that the hanging location allows the blades a clearance and of 7.6ft.(2.3m) and 20in(50cm) from any wall or obstruction 0.5M 2.
Installation 2 Tools Needed You may need the tools below: . . . . . .
Installation 3 Parts Inventory 1 6 11 2 7 12 3 1. Mounting Bracket 2. Top Canopy 3. Decorative Cover 4. Downrod Canopy 5. Motor Body 6. Lamp panel 7. LED 8H 4H 1H 5 4 3 10 6 9 OFF 5 13 2 8 1 4 14 8. Lampshade 9. Downrod 10. Blades 11. Mounting Screws Kit 12. Blades Bag 13. Accessory Bag 14.
Installation 4 Secure Bracket . Secure to Outlet Box If there isn't an existing outlet box, then install one using the following instructions: . Disconnect the power by removing the fuses or turning off the circuit breakers. . Secure the outlet box (A) (not included) directly to the building structure. Use appropriate fasteners and materials (not included). The outlet box and its bracing must be able to fully support the weight of the moving fan (at least 35 lbs). .
Installation 4 Secure Bracket . Secure to Ceiling Attach the mounting bracket to the ceiling. There are two types of screws included in the pack. For wooden ceiling Drilling a pilot hole in your ceiling with the power drills first, then secure the plate with wood screws Wood screws Beam For concrete ceiling Drill a hole in the base material with a hammer drill and a correctly sized carbide drill bit for the anchor and clean out the hole of all debris.
Installation 5 Assembly of Downrod Locking pin Downrod setscrew Pin Downrod setscrew Choose the proper downrod 1. Put the downrod through the top canopy and the downrod canopy 2. Pass the wire from the motor body through the downrod 3.
Installation 6 Mount Fan to Bracket Hanger lugs Lobed coneave groove . Place the lobes in the hanger and turn the pipe so that thegroove on the lobes engages thelugs on the dome(inside thehanger) The lug grouve must engage the hanger lug. . Replace the long pipe: first take out 2 screws, then take out the horizontal pin, then replace the short pipe with the long pipe, insert the horizontal pin back, and lock the 2 screws.
Installation 7 Wiring in L(black) Light L(Blue) Light N(white) in N(white) Light W-(white) Light U+ (black) Light Y- (Red) Insert the receiver into the top of the fan body and make wire connections according to wire colors, labels, and diagram above. *Wrap each wire connector separately with electrical tape as an extra safety measure.
Installation 8 Blade Installation blade screws Insert a blade screw from the package through the blade hole and position it under the motor so that the screw is aligned with the "center" hole position of any group of two screw holes. Using the screwdriver to secure the blade to the motor, but do not over tighten. Repeat for the rest blades. Once all blades screws are in place, gently tighten all screws with the screwdriver.
Installation 9 Installation of Light Kit 1. Remove the screws on the motor plate first. 2. Align the hole on the light mounting box to the motor plate. 3. Make the light plug on from the motor come through the central hole on the box. 4. Insert the screws and tighten them to secure the motor housing 5. Connect the plugs and Adopt the LED board to the mounting box 6.
Maintenance Here are some suggestions to help maintain your fan . Because of the fan's natural movement, some connections may become loose. Check the support connections, brackets, and blade attachment twice a year. Make sure they are secure. . Clean your fan periodically to help maintain its new appearance over the year. Do not use water when cleaning. This could damage the motor, or possibly cause electrical shock. . Use only a soft brush or lint-free cloth to avoid scratching the finish.
Troubleshooting Please read all installation instructions carefully. After reviewing the following tips, if you are unable to solve a problem, please contact customer service for additional assistance WARNING Before servicing or cleaning your fan, switch power off at the service panel and lock the service disconnecting means to prevent power from being switched on accidentally. Fan not reponding to remote control Check that all wire connections are secure and made as instructed.
Troubleshooting Fan makes humming noise . Be sure you are using the control set supplied with your fan . Make sure all fittings are firmly secured. Loose parts will often cause vibrational noise or humming. Removal and re-attachment can sometimes remedy such resonant vibrational noise. Fan woobles Make sure the mounting plate and hardware at the ceiling are secure and firmly fastened. If necessary, use the wood screws provided to further secure the outlet box to the joist.
