USB3.
Package checklist Please Check if the following items are present and in good condition upon opening your package. Contact your vendor if any item is damaged or missing. 1. USB3.0 PCI Express Host Card 2. CD Driver 3. User’s Manual(this document) System Requirement One available x1,x4,x8 or x16 PCI Express slot.(Recommend PCI Express 2.0) Microsoft Windows 7,8.x and 10 operation system. INTEL Core i processor with 4GB DDR RAM or above.
Features PCI Express Base Specification Revision 2.0 single-lane(x2). Compliant with Universal Serial Bus 3.0 specification GEN1. Compliant with xHCI (eXtensible Host Controller interface)SPEC Rev 1.0. Supports simultaneous operation of multiple USB3.0,2.0&1.1 devices. Supports USB data transfer rate of 5G/480/12/1.5Mbps Each USB port supplies maximum +5VDC/900mA power output to USB device. Built-in over current protection on the USB port.
Safety First To avoid damaging, make sure to discount power disposing USB card Installation. connection before wiring or Note: 1. In order to output effieient +5VDC power to USB device, (be sure to plug SATA power cable (from PS’s power supply) into USB3.1 card’ s SATA power connector,if need). 2. In order to get USB3.0 Super Speed+performance, please use PCI Express Generation2 slot for card installation. Or only get half of the data transfer rate.
or eject your USB devices. Specification Hardware BUS PCI Express Spec 2.0, Single-Lane (x1) Controller PCI Express USB3.0 Host controller USB Standard eXtensible Host Controller interface (xHCI) Rev1.1 IRQ & IO Assigned by System USB Communication Interface Universal Serial Bus 3.0/2.0/1.1 Super Speed(5Gpbs) High Speed(480Mbps),Full Speed(12Mbps), Speed Low Speed (1.5Mbps) Driver Support Microsoft Environment Operation Temperature Operation Humidity Storage Windows 7 (x86/x64) Windows 8.
Driver Installation USB3.0 PCIE Host card design bases on Microsoft Windows operation system The table in this topic provides the operating system for the driver support lists. Operating System USB3.0 Driver Remark Windows 10 Windows8/8.1 Microsoft Windows in-box driver(with Driver Free UASP) Windows Server2008R2 Windows XP/7 Driver is User has to install additional USB3.0 Necessary driver. WindowsServer2008 *USB3.0 Host * USB3.0 Host IC Driver(without R2 Diver UASP).
(2)Click “Next” and then click “OK” to continue.
(3)Specify driver installation folder in system and click “Next” to continue Click”Finish” to end of the Driver intalltion steps.
Under Win7 and 2008 OS, entry Universal Serial Bus controllers catalog, and “Fresco Logic xHCI (USB3) Root Hub” shows in the device manager. Driver Uninstall Click on the “Programs and Features” tab in the Windows Control Panel Start>Control Panel> Programs and Features Entry Uninstall or change a program page, and double click “Fresco Logic xHCI (USB3) Root Hub” to process driver uninstallation procedure.
Troubleshooting Q1. If card and devices connected to the computer do seem to be working properly, please perform below basic troubleshooting steps: Ans: a. Check that all cables are correct and securely connected. b. Make sure USB device’s power is turned on. c. Make sure the devices are getting enough power they require. d. Make sure there is no problem with the card installation. e. Make sure to plug SATA power cable(from PC’s Power Supply)to the add-on card’s SATA port( option) Q2.
Ans:a.Please shutdown your computer and move the card to another available slot then re-install USB3.1 driver. b.Please point on this device then right-check on the mouse. Selecting “Update Driver” to renew USB driver. c.This exclamation point usually means there is a resource conflict between the this card and another card in your system. . Please move the card to another available slot.Restart your computer. Windows will re-configure itself and re-assign resources.Check your device manager again. Q4.
