Ultimaker 2+ Connect EN 10/2020 v1.
Table of contents 1. Safety and compliance 1.1 Safety messages 1.2 General safety information 1.3 Hazards 1.4 Regulatory information 4 4 5 6 2. Introduction 2.1 Main components 2.2 Specifications 9 11 3. Installation 3.1 Unboxing 3.2 What's in the box? 3.3 Hardware installation 3.4 First setup 3.5 Firmware update 3.6 Install Ultimaker Cura 13 14 15 16 17 18 4. Operation 4.1 Touchscreen 4.2 Materials 4.3 Preparing a print with Ultimaker Cura 4.4 Printing with the Air Manager 4.
Disclaimer This manual sets out the instructions on how to install and operate the Ultimaker 2+ Connect. Please read and understand the contents of this installation and user manual carefully. Failure to read the manual may lead to personal injury, inferior print results or damage to the Ultimaker printer or its peripherals. Always make sure that anyone who uses this 3D printer knows and understands the contents of the manual to make the most out of the Ultimaker printer.
1.
1.1 Safety messages The information provided below is applicable to the Ultimaker 2+ Connect and Ultimaker 2+ Connect Air Manager (“Ultimaker products”). This guide contains warnings and safety notices. Provides additional information that is helpful to do a task or to avoid problems Warns of a situation that may cause material damage or injuries if the safety instructions are not followed.
1.3 Hazards Electrical safety The external power supply should not be tampered with. If due to a defect replacement is needed, it should only be replaced by the original type mains socket with protective earth/ground terminal must be used. Make sure that the building installation A has dedicated means of over-current and short-circuit protection. Please use a circuit breaker with a current rating not exceeding 16A. For more information, please visit our website for the CB-certificate.
Safe use information for Ultimaker materials. Ultimaker materials can be printed safely without any filtering using the recommended temperatures and settings in a well-ventilated area (minimum refresh rate or AER of 1.8 for a room size of 30.6 m3). When multiple Ultimaker 3D printers are operated in a contained environment, concentrations of UFPs and/or VOCs will increase.
FCC / ISED regulatory notices • Modification statement. Changes or modifications not expressly approved by Ultimaker could void the user’s authority to operate the equipment • Wireless notice. This device complies with FCC/ISED radiation exposure limits set forth for an uncontrolled environment and meets the FCC radio frequency (RF) Exposure Guidelines and RSS-102 of the ISED radio frequency (RF) Exposure rules.
2.
2.1 Main components Ultimaker 2+ Connect with Air Manager 1 2 1. Air Manager 2.
Ultimaker 2+ Connect 3 4 2 7 1 8 9 6 1. 2. 3. 4. 5 Print head Print head cable Build plate Build plate clamps 13 5. 6. 7. 8. Touchscreen display USB port Bowden tube Feeder 12 11 9. 10. 11. 12. 13. 10 On/off button OUT port Power socket Spool holder Ethernet port Air Manager 3 2 1 6 4 7 5 9 1. Filter 2. Air Manager cover 3. Handle Ultimaker 2+ Connect user manual 4. Front enclosure 5. Hinge profile 6. Fan 8 7. Filter housing 8. Air Manager cable 9.
2.2 Specifications Properties Technology Fused filament fabrication (FFF) Print head Single extrusion print head with swappable nozzles Build volume (XYZ) 223 x 220 x 205 mm (8.7 x 8.6 x 8 in) Nozzle diameter 0.4 mm (included) 0.25 mm, 0.6 mm, 0.8 mm (sold separately) Layer resolution 0.25 mm nozzle: 150 - 60 micron 0.4 mm nozzle: 200 - 20 micron 0.6 mm nozzle: 300 - 20 micron 0.
3.
3.1 Unboxing Ultimaker 2+ Connect The Ultimaker2+ Connect comes in reusable, durable packaging, specially designed to protect your 3D printer. Follow the steps below properly to unpack your Ultimaker printer. I t is recommended to remove the packaging with the box placed on the floor for safety. Please retain all packaging for warranty purposes. When placing the printer on a shelf or table, take proper measures to prevent the printer from falling. 1.
3.2 What's in the box? Ultimaker 2+ Connect The Ultimaker 2+ Connect is supplied with several hardware accessories. Check if all these items are included before continuing: Accessories 1. 2. 3. 4. 5. 6. 7. Glass plate Spool holder Power adapter and cable Ethernet cable USB stick Calibration card 0.4 mm nozzle Consumables 8. 9. 10. 11. Tools 12. 13. 14. 15. Hex screwdriver 2 mm Hex key 2.5 mm Nozzle wrench Print head calibration aid Documents 16. Quick start guide 17.
3.3 Hardware installation Ultimaker 2+ Connect 1. Insert the spool holder into the back panel and push until it snaps into place 2. Open the front build plate clamps to insert the glass plate 3. Slide the glass plate into the rear build plate clamps, then close the front clamps The warning icon (hot surface) on the glass plate should face upwards. 4.
3.4 First setup After installing the hardware accessories, set up the printer for first use. Turn on the printer with the power switch at the back. After booting up, you will see the home screen. This displays your printer status, and allows you to quickly navigate to the Materials, Settings or Maintenance menus. I t is possible that the Ultimaker 2+ Connect shows a firmware upgrade screen when it boots up for the first time. If this is the case, go to ultimaker.
Network connection The Ultimaker 2+ Connect can connect to a local area network, using either Wi-Fi or Ethernet. Select the Settings menu and navigate to Network configuration. Follow the instructions on the display. Set up Wi-Fi To connect your Ultimaker 2+ Connect to a wireless network, you will need a computer or a smartphone. Select Connect via Wi-Fi to start the Wi-Fi setup and follow the steps on the touchscreen: 1. Wait until your printer has created a Wi-Fi hotspot. This may take a moment 2.
3.6 Install Ultimaker Cura After successfully setting up your printer, install Ultimaker Cura – Ultimaker’s free print preparation software on your computer. You can download Ultimaker Cura at ultimaker.com/software. or more information about Ultimaker Cura and system requirements, please consult the Ultimaker Cura user F manual at support.ultimaker.com. After downloading, run the installer to complete the installation of Ultimaker Cura.
4.
4.1 Touchscreen You can control the Ultimaker 2+ Connect by using the touchscreen at the front of the printer. Interface The main menu offers three options, represented by the following icons: Materials. This menu shows which material is currently loaded. It also offers the options to change, load, or unload material, or select a different material type. Settings. In this menu, you can update the firmware, connect to the Digital Factory, and change settings for the frame lighting. aintenance.
4.2 Materials Material compatibility The Ultimaker 2+ Connect supports all Ultimaker build materials that are currently available, of which most can be printed with the 0.25, 0.4, 0.6, and 0.8 mm nozzle sizes. All Ultimaker materials have been extensively tested and have optimized profiles in Ultimaker Cura to ensure the best print results. Therefore, it is advised to use one of the default profiles in Ultimaker Cura for the highest reliability.
4.3 Preparing a print with Ultimaker Cura Interface 1 2 3 4 5 9 8 7 6 After adding the Ultimaker 2+ Connect in Ultimaker Cura, the main interface will become visible. Here is an overview of the user interface (UI). UI elements: 1. 2. 3. 4. 5. 6. 7. 8. 9. Open file Printer selection panel Stages Configuration panel Print settings panel Action panel 3D viewer Camera position tool Adjustment tools The Ultimaker Cura workflow is arranged in three stages, seen at the top of the interface.
Prepare stage Load a model and prepare it for slicing in the prepare stage of Ultimaker Cura. 1. Load the model(s) by clicking the ‘open file’ folder icon 2. In the configuration panel, select the material type you wish to print with 3. Use the adjustment tools to position, scale, and rotate the model as desired The adjustment tools are visible when a model is loaded and selected on the 3D viewer. 4.
4.4 Printing with the Air Manager The optional Ultimaker 2+ Connect Air Manager is designed to simply and effectively increase user safety. The Air Manager consists of the top cover, filter, and front enclosure. Proper use of the Air Manager minimizes the emission hazards related to UFPs caused by 3D printing materials. he Air Manager is highly recommended in classrooms, when printing with materials that emit significant T amounts of UFPs, or in locations with multiple 3D printers.
4.5 Remove the print Once your 3D print is finished it must be removed from the build plate. There are several methods to do this. hen using a brim, be aware of the danger of cutting yourself when removing the print from the build plate. W Use a deburring tool to remove the brim once the print is taken from the build plate. lways use the recommended adhesion method. Printing directly on the glass with certain materials can cause A the build plate to chip.
4.6 Change the printer configuration Change material Materials can be changed easily on the Ultimaker 2+ Connect. Select the Materials menu and navigate to Change material. Follow the instructions on the display. 1. Select the new material type. If you want to load a new spool of the same material, select Yes. If you are changing to a different material, select No and choose the new material type on the next screen 2. Wait for the nozzle to heat up 3.
5.
5.1 Update the firmware Periodically, a new version of the Ultimaker 2+ Connect firmware is released. To ensure that your Ultimaker 2+ Connect is equipped with the latest features, it is recommended to keep the firmware updated to the latest version. Update over the network If the Ultimaker 2+ Connect is connected to a network, it automatically checks for available firmware updates. When a new firmware is available, the printer will prompt you to download and install it via the touchscreen interface.
5.3 Maintenance schedule To keep your Ultimaker 2+ Connect in optimal condition, we recommend the following maintenance schedule, based on 1,500 printing hours per year. I f the usage frequency is higher, we recommend performing more frequent maintenance on your printer to ensure optimal printing results. aintenance actions shall only be performed by an adult. Carefully follow the provided instructions. Where M possible, ensure the printer is turned off before performing maintenance.
5.4 Replace the Air Manager filter The filter in the Air Manager is a consumable. It should be replaced every 1,500 printing hours to maintain proper filtering. o not change the filter of the Air Manager while the fan is in operation. Turn off the printer to make sure the D fan cannot start unexpectedly. he function of the Air Manager’s filter is to reduce the emission of ultrafine particles. These particles will T remain in the filter.
6.
6.1 Error messages When the printer detects that something is wrong, or when it reads values outside of the allowed range, an error will occur. The display will give a short description of the detected issue along with its unique error code. For example: • Detected nozzle temperature is invalid. Go to ultimaker.com/ER201 Go to the specified page to learn more and for troubleshooting tips. 6.
Cold pull 1. In the Set nozzle temperature menu, use the controls to lower the nozzle temperature to 135 ºC for cleaning filament, or 90 ºC for PLA 2. Continue to apply some pressure on the material in the print head with pliers 3. When the nozzle has reached the target temperature, use the pliers to pull out the filament with a quick, firm pull 4. Inspect the tip of the filament.
6.4 Air Manager troubleshooting Air Manager not recognized You can check if the Air Manager is detected by the Ultimaker 2+ Connect in the Diagnostics menu. Navigate to Maintenance → Diagnostics to check the Air Manager status. If the Air Manager is installed, but listed as ‘not present’, it may not be connected properly. Follow the steps below to check the Air Manager cable: 1. Power off the Ultimaker 2+ Connect 2. Ensure one end of the Air Manager cable is securely inserted into the filter housing.
7.
7.1 General Ultimaker grants a standard warranty on the Ultimaker 2+ Connect and Air Manager (“Product”) in the country where the product was purchased. From the date the product is sold and delivered to an end customer for the first time, as evidenced by the original customer’s purchase invoice, Ultimaker warrants the product is free from defects in material, design, and workmanship for a period of twelve (12) months.
7.3 Notification The Ultimaker resellers deal with this warranty on behalf of Ultimaker. Therefore, any notification on the basis of this warranty must be made to the Ultimaker reseller from whom the product was originally purchased, even if this is not in the customer’s present country of residence. Any warranty claim must first be recognized as justified, either by Ultimaker’s reseller or by Ultimaker. If so, the reseller is obliged to rectify the defects free of charge according to this warranty.
Support For more information on technical support, visit support.ultimaker.
