Installation & Assembly

UF13700
UF13703
UF13705
UF13707
Installation/Installation/Instalación
Prior to Installation:
• Turn off the hot and cold water supply at the angle stops and turn on the old faucet to release any built up pressure.
Remove existing faucet. Clean sink or countertop to remove any debris, plumber’s putty, or silicone.
• Place bucket under angle stops. Turn on to flush any debris prior to installing new plumbing. Shut off angle stops.
• Pre-drilled hole size requirement: 1-3/8” (min) – 1-1/2” (max)
• Max countertop thickness without deck plate: 1-1/2”
• Max countertop thickness with deck plate: 1”
Care & Maintenance:
* To keep the product clean & shining, follow the steps below:
• 1. Rinse with clean water & dry with a soft cloth.
• 2. Do not clean with soaps, acid, polish, abrasives, or harsh cleaners.
• 3. Do not use cloth with a coarse surface.
• 4. Unscrew the aerator and clean when necessary.
This installation manual is subject to change without further notice.
Please read your care and maintenance documentation to determine the limits of proper use.
This product has been manufactured and tested to the highest quality standards .We offer our customers thoughtfully
crafted fixtures & accessories, engineered for enduring performance over years of use.
1/16”(1 mm) min. 1-1/2”(38 mm) max.
1-3/8” (35 mm) min.
1-1/2” (38 mm) max.
1/16”(1 mm) min. 1”(25.4 mm) max.
1-3/8” (35 mm) min.
1-1/2” (38 mm) max.
Without deck plate: With deck plate:
1
Place the new faucet through flange(10) on the mounting
surface.
2
Assemble rubber washer(11), metal washer(12) and thread
mounting nut(13) onto shank form underside of sink.Hand
tighten, secure locking screws(14) on mounting nut(13)
and tighten locking screw(14) using screw driver.
3
Thread hot & cold waterlines onto angle stops. Tighten with
adjustable wrench until snug. Turn on the angle stops and
check for leaks .
(DO NOT TURN FAUCET ON)
4
Install spray hose assembly(8). Connect hose to outlet hose
(18) and tighten. Do not overtighten.
WARNING: Be sure to install the Check valve(17).
10
11
12
13
14
Hot
Cold
Hose
8
18
17
Screws
15
Hot
Cold
7
5
Attach weight (15) on the designated mark on the spray
hose.
6
Important: After installation is completed. Remove spray
head (7).Hold tip of spray hose. Turn faucet on for 1 minute
to flush any debris. Reconnect spray head (7).While water
is running,check for leaks. Re-tighten if necessary,but do
not over-tighten.
Trouble-Shooting:
If you have followed the instructions carefully and your faucet still does not work properly,take the following corrective steps:
Leakage under handle
Locking nut has come loose
or cartridge needs to be
reseated
Loosen the set screw located at the base of the handle with
a hex wrench. Remove the handle and unscrew cartridge
holder by hand.Tighten locking nut with an adjustable wrench.
Water will not shut off
completely
Cartridge may need to be
adjusted or replaced
Loosen the set screw located at the base of the handle with a
hex wrench. Remove the handle and unscrew cartridge cover
by hand.Unscrew the locking nut with an adjustable wrench.
Remove ceramic disc cartridge.Check for cracks,and if O-ring
is seated correctly,Reseat cartridge.
Leaking between spray
head and hose
Spray head may be loose,or
washer may not be seated
correctly in the hose connection
Tighten the spray head by hand until snug,Make sure the
washer is seated correctly.
Hose does not retrace
Weight may not be installed
correctly
Readjust the weight on the hose.