5 IN 1 POWER STATION WITH JUMP START WARNING This product contains or, when used, produces a chemical known to the State of California to cause cancer and birth defects or other reproductive harm. (California Health & Safety Code § 25249.5, et seq.) *Actual product may vary slightly Please carefully read and save these instructions before attempting to assemble, maintain, install, or operate this product. Observe all safety information to protect yourself and others.
SPECIFICATIONS AC Output Power Inverter No Load Current Battery Booster Cables 26″ L With Copper-Plated Clamps Fuse 12V 40A Low Voltage <10.8V - 11.3V Warning Low Voltage 8.9V - 9.4V Shutdown Functions: 12 Volt Jump-Starter, 300 PSI Air Compressor, 200W Power Inverter, Power Supply, and Work Lights Continuous Peak Voltage Frequency 200W 400W 115V 60Hz Modified Sine Wave Wave Form (non-sinusoidal) <0.
PERSONAL SAFETY 1. Wear ANSI-approved splash-resistant safety goggles and heavy-duty rubber work gloves whenever connecting, disconnecting, or working near battery. Battery acid can cause permanent blindness. Avoid touching eyes while working near battery. 2. Do not use Power Pack while you are tired or under the influence of drugs, alcohol or medication. A moment of inattention while operating Power Pack may result in serious personal injury. 3.
c. Some rechargeable tools and appliances can damage the Inverter. Check the temperature of the device several times when it is charging. If the device becomes extremely hot; turn the power off, remove the device, and do not use with the Inverter again. d. Do not attempt to power a device, or combination of devices, that will require more than the rated output of this Inverter. This may damage the Inverter or the attached devices. e.
FUNCTIONS Connection Indicator Light Work Light Work Light Work Lights Switch Compressor Switch Air Pressure Gauge Voltmeter Battery Test Button Charging Input Positive Battery Cable (Not Shown) 12VDC Outlet Clamp Power Switch Charging Indicator Light 12VDC Outlet Negative Battery Cable (Not Shown) Front Work Light Work Light Inverter Power Indicator Light Fuse Inverter Switch USB Connector Inverter Overload Indicator Light 115VAC Outlets Air Hose Compartment Fan Back Figure A customer
CHARGING THE POWER PACK WARNING! Always charge on a non-flammable surface. 1. Press and hold the Battery Test Button on the front of the unit to check the battery power level. a. 13-15 volts is ready for use. b. 12 volts needs to be charged. c. Less than 12 volts should be charged immediately. 2. Turn the Clamp Power Switch on front of unit to the OFF position. 3. Plug the 120VAC Adapter into a 2 or 3-prong outlet. (See Figure B.) 4. Plug the Adapter cord into the Charging 5.
AC APPLIANCE COMPATIBILITY The Power Pack has two Outlets for AC appliances. The total load from both outlets must not exceed the AC Outlet power listed in the Specifications Chart. Some appliances may have a high initial surge which may make them incompatible with this unit. Calculate the total wattage needed to start up the appliances, and the total wattage needed to run the appliances before operation.
Modified Sine Wave The Inverter can only power AC appliances which are compatible with a Modified Sine Wave (non-sinusoidal). Note: Only multimeters identified as “TRUE RMS” will read Modified Sine Wave voltage accurately. Modified Sine Wave power is suitable for most AC devices and power supplies used in electronic equipment, transformers, and motors. Modified Sine Wave (MSW) Sine Wave Note: Do not use to power sensitive devices such as medical equipment.
USING THE WORK LIGHTS 1. To turn the Work Lights on, push the Work Lights Switch to the “I” (ON) position. 2. To turn the Work Lights off, push the Work Lights Switch to the “O” (OFF) position. JUMP STARTING A VEHICLE Note: Read the vehicle owner’s manual pertaining to jump starting prior to using the Power Pack. 1. Press the Battery Test Button to verify that the Power Pack is fully charged. Recharge as needed, following the instructions in the Setup section under “Charging the Power Pack” on page 6. 2.
Using Hose Adapters 1. Three adapters are included with the Power Pack that can be attached to the Tire Inflator. (See Figure G.) 2. Attach the proper adapter to the Tire Inflator for the object to be inflated. 3. Insert the adapter into the object’s receptacle and press down the lever. 4. Push the Compressor Switch to the “I” (ON) position. Note: Monitor the Air Pressure Gauge on the front of the unit to avoid over-inflation. 5.
CHARGING USB DEVICES 1. Press the Battery Test Button to verify that the Power Pack is fully charged. Recharge as needed, following the instructions in the Setup section under “Charging the Power Pack” on page 6. 2. Before connecting the device, make sure the Inverter Switch is in the “O” (OFF) position. 3. Plug the device into the USB Connector. 4. Push the Inverter Switch to the “I” (ON) position. If the Inverter is working correctly, the Inverter Power Indicator Light will illuminate. 5.
INVERTER TROUBLESHOOTING Problem Lack of Inverter power output. Possible Causes Possible Solutions 1. Power Pack voltage at or below 12V. 2. Excessive current drawn during operation. 3. Inverter not completely warmed up. 1. Recharge the Power Pack immediately. Inverter LED Light off. 1. Inadequate power or excessive voltage drop. 2. Inverter is overloaded. 1. Check Power Pack and recharge if voltage drops below 12V. 2. Reduce load to 200 watts. Appliance/device won’t operate.
PARTS LIST 7 11 12 30 1 13 15 24 31 32 33 14 17 customerservice@focus-ontools.
Limited Manufacturer Warranty FOT makes every effort to ensure that this product meets high quality and durability standards. FOT warrants to the original retail consumer a 1-year limited warranty from the date the product was purchased at retail and each product is free from defects in materials. Warranty does not apply to defects due directly or indirectly to misuse, abuse, negligence or accidents, repairs or alterations, or a lack of maintenance.
