Instructions / Assembly

Issued/Revised:
04/26/13
VINE CLIMBER 02-07-5008
uPLAY TODAY
800.458.5872
www.ultraplay.com
1
Parts List
PART NUMBERQTYDESCRIPTION
02-07-00321
VINE CLIMBER
02-07-00851DECK MOUNTING BRACKET
02-07-00972
VINE CLIMBER EXTENSION POST-LONG
02-07-00982VINE CLIMBER EXTENSION POST-SHORT
02-07-00462
FOOTER PLATE
02-07-00332GRAB BAR
02-07-00394
TUBE CLAMP
33-12-00771
33-11-0002*
3
M10 x 20mm (3/4") BHCS BOLT
33-11-0003*
4
M10 x 25mm (1") BHCS BOLT
33-11-0203*
4
M12 LOCKWASHER
33-11-0200*
7
M10 FLATWASHER
33-11-0005*
2
M10 x 35mm (1 3/8") BHCS BOLT
33-11-0400*
5
M10 LOCK NUT
33-11-0103*
12
M8 x 25mm (1") BHCS BOLT
33-11-0301*
4
M8 LOCKWASHER
33-11-0500*8
M8 LOCK NUT
33-11-0700*
4
CLAMP RIVET
HARDWARE COMPLETE
Items listed below Hardware Complete line are included with Hardware Complete Number
Warning: During Installation, Hardware And Small Parts Are Choking Hazards For Young Children. Store
Unused Parts Appropriately Until Assembly Is Completed. Once Assembly Is Completed, Remove Any
Unused Parts From The Play Environment And Dispose/Save Them In A Secure Location. Any bolt end
protruding more than two full threads beyond the face of the nut causes risk of clothing entanglement.
Promptly cut-off flush, file smooth, and treat to prevent corrosion.
Unless Otherwise Specified, All Units of Measure are Each
Note: Peen Tee-Nuts and Flatwashers to match radius of pipe after assembly is complete.
Note: Loctite (supplied by others) should be used on any non-patch hardware.
INSTALLATION INSTRUCTIONS:
IMPORTANT:
DETERMINE WHICH MOUNTING OPTION YOU ARE USING; SURFACE MOUNT, ONGROUND, OR IN-GROUND.
1. Choose the appropriate Deck to receive Vine Climber.
2. Clean out slots in Deck with utility knife if necessary.
3. Attach Deck Mounting Bracket to Deck using M10 x 20mm B.H.C.S. Bolt, M10 Flat Washer,and M10 Lock Nut. See Detail 040.
NOTE:
THERE ARE (2) LENGTHS OF EXTENSION POSTS INCLUDED IN YOUR INSTALLATION KIT. USE THE 15" EXTENSION
POST FOR THE ENGINEERED WOOD FIBER AND 8 1/4" EXTENSION POST FOR 2" RUBBER TITLES OR POURED-IN-
PLACE SURFACING.
4. Locate Footer Plate and Insert Extension Post onto Footer Plate and secure with M10 x 35mm B.H.C.S. Bolt and M10 Lock Nut.
See Detail 036.
5. Attach Extension Post to Vine Climber using M10 x 25mm B.H.C.S. Bolt, M12 Lock Washer, and M10 Flat Washer. See Detail 041.
6. Attach Vine Climber to Deck Mounting Bracket using M10 x 25mm B.H.C.S. Bolt, M12 Lock Washer, and M10 Flat Washer. See
Detail 042.
7. Insert shaft of Tube Clamp onto Grab Bar and secure using M8 x 25mm B.H.C.S. Bolt and M8 Lock Washer. See Detail 029.