Instructions / Assembly

Parts List
PART NUMBER
QTYDESCRIPTION
02-07-00261
STRAIGHT SLIDE
02-07-00451MOUNTING BRACKET
02-07-00441
EXTENSION TUBE
02-07-00461
FOOTER PLATE
02-07-00251SLIDE HOOD
33-12-00711
33-11-0002*
5
M10 x 20mm (3/4") BHCS BOLT
33-11-0203*
7
M12 LOCKWASHER
33-11-0200*
7
M10 FLATWASHER
33-11-0005*2M10 x 35mm (1 3/8") BHCS BOLT
33-11-0400*
2
M10 LOCK NUT
33-11-0007*
2
M10 x 60mm (2 3/8") BHCS BOLT
33-11-0106*2M8 x 40mm (1 9/16") BHCS BOLT
33-11-0300*
4
M8 FLATWASHER
33-11-0500*6
M8 LOCK NUT
33-11-0102*
2
M8 x 20mm (3/4") BHCS BOLT
33-11-0501*
2M8 BARREL NUT
33-11-0103*
4
M8 x 25mm (1") BHCS BOLT
33-11-0700*
2
CLAMP RIVET
05/22/13
4FT. STRAIGHT SLIDE 02-07-5004
uPLAY TODAY
800.458.5872
www.ultraplay.com
1
HARDWARE COMPLETE
Items listed below Hardware Complete line are included with Hardware Complete Number
Warning: During Installation, Hardware And Small Parts Are Choking Hazards For Young Children. Store
Unused Parts Appropriately Until Assembly Is Completed. Once Assembly Is Completed, Remove Any
Unused Parts From The Play Environment And Dispose/Save Them In A Secure Location. Any bolt end
protruding more than two full threads beyond the face of the nut causes risk of clothing entanglement.
Promptly cut-off flush, file smooth, and treat to prevent corrosion.
Unless Otherwise Specified, All Units of Measure are Each
Note: Peen Tee-Nuts and Flatwashers to match radius of pipe after assembly is complete.
Note: Loctite (supplied by others) should be used on any non-patch hardware.
INSTALLATION INSTRUCTIONS:
IMPORTANT:
DETERMINE WHICH MOUNTING OPTION YOU ARE USING; SURFACE MOUNT, ONGROUND, OR IN-GROUND.
1. Locate Slide and attach Mounting Bracket using M10 x 20mm B.H.C.S, M12 Lock Washer, and M10 Flat Washer. See Detail 057.
2. Attach Extension Tube to Mounting Bracket using M10 x 35mm B.H.C.S. and M10 Lock Nut. See Detail 014.
NOTE:
DISCARD EXTENSION TUBE IF USING 2" POURED-IN-PLACE OR RUBBER TILE APPLICATIONS AND BOLT MOUNTING
BRACKET DIRECTLY TO FOOTER PLATE.
3. Insert Footer Plate into Extension Tube and secure using M10 x 35mm B.H.C.S. and M10 Lock Nut. See Detail 036.
4. Clean out slots in Deck with utility knife if necessary.
5. Attach Slide to Deck using M10 x 20mm B.H.C.S, M12 Lock Washer, and M10 Flat Washer. See Detail 058.
6. Attach Slide Hood to Slide using M10 x 60mm B.H.C.S, M12 Lock Washer, and M10 Flat Washer. See Detail 059.
7. Attach Bottom of Slide Hood to Deck using M8 x 40mm B.H.C.S, M8 Flat Washer, and M8 Lock Nut. See Detail 060.